CONTENTS Installation .....................................................................................................3 DIN Front-Mount....................................................................................................3 Installing the unit.............................................................................................3 Removing the unit...........................................................................................4 Using the Detachable Front Panel ............
INSTALLATION Notes: TAKE OUT SCREWS BEFORE INSTALL • The unit can be installed on the vehicle or the ships. Before install the unit, please remove the two screws. • Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Take out screw before installation • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly.
INSTALLATION Removing the unit 1 6 1 2 5 3 7 4 Front Panel OPEN button (Fig. 2) 2 1. 2. 3. 4. 5. 6. Dashboard Nut (5mm) Spring washer Screw (5x25mm) Screw Strap Be sure to use the strap to secure the back of the unit in place. The strap can be bent by hand to the desired angle. 7. Plain washer 1. Before removing the unit, press the OPEN button to slide down the front panel. 2. Key Insert the keys supplied with the unit into the grooves in the housing as shown in figure until they click.
USING THE DETACHABLE FRONT PANEL To Detach the Front Panel To Reinstall the Front Panel 1. Press the OPEN button, the front panel will slide down. 1. When the panel bracket is in slide down position, insert the front panel into the panel bracket and push the front panel from the middle to slide it up. Open Bottom Button 2. When the front panel slides down, press the bottom button of the front panel upward and pull it out from the panel bracket. 2.
WIRING CONNECTION MAIN UNIT (BLACK) WIRING REMOTE CONNECTOR SOCKET (BLACK) CD CHANGER CONNECTOR SOCKET ANTENNA SOCKET IGNITION RED SWITCH (B+) FUSE AUX IN (YELLOW) Rch RED Lch WHITE Constant YELLOW 12 Volts (BROWN) GROUND (B–) BLACK Rch RED FRONT RCA CABLE Lch WHITE (GREY) REAR RCA CABLE POWER BLUE ANTENNA FRONT Lch SPEAKER REAR Lch SPEAKER Rch RED Lch WHITE WHITE GREY WHITE/BLACK GREY/BLACK GREEN VIOLET GREEN/BLACK VIOLET/BLACK 6 FRONT Rch SPEAKER REAR Rch SPEAKER
OPERATION 16 9 11 10 6 12 13 8 15 21 14 22 23 17 19 20 18 1 2 5 4 3 7 24 Press the VOL button (11) or VOL button (12) to adjust the selected mode. When the currently displayed function has not been adjusted for several seconds, the mode shall return to volume position and display will return to normal radio, CD or CDC display. GENERAL OPERATION • ON/OFF Switch on the unit by pressing POWER button (9). When system is on, press POWER button (9) again to turn off the unit.
OPERATION BEEP ON/OFF Program power on volume level CLOCK ON/OFF while power off USA/EUR FREQ/CLOCK/NO PRI priority 12hours/24hours 12hours/24hours In this mode, you can set 24 hours mode or 12 hours mode. • When the currently displayed function has not been adjusted for several seconds, it will exit menu set mode. • When you have set CLOCK ON during power off state, LCD backlight will be turn on together.
OPERATION 6 strongest stations are stored into the corresponding preset number button. When all completed, it will change to scan preset station automatically. • RESET Reset button (24) must be activated with either a ballpoint pen or thin metal object. The reset button is to be activated for the following reasons: - Initial installation of the unit when all wiring is completed. - All the function buttons do not operate. - Error symbol on the display.
OPERATION order. When you have selected 32 tracks to be programmed. “FULL” will appear on the display. - When the CD is played in programmed order by pressing PGM button (20), pressing it again will exit PGM mode. - When the disc is playing in programmed order, pressing MEM button (19) will cancel the all programmed content and “CLEAR” appears on the display. - If you don’t press MEM button (19) to carry out program setting, then press PGM button (20), “NO-PGM” will appear.
OPERATION SELECT BY SCAN/MP3 BUTTON: “Searching track directly” => “Searching Directory or File Name”=> searching from root by VOL / buttons (11&12) =>searching from current directory by VOL / buttons (11&12). 1. SEARCHING TRACK DIRECTLY Press the MP3 button (13) one time to enter into “Searching track directly” mode. Set desired track by VOL / buttons (11&12), and then press BAND/ENTER button (18) shortly.
OPERATION Key Assigned in Searching mode (Table 1) Normal In MP3 seaching SCAN MP3 Seaching Mode Select BAND ENTER M1 A, B, C, 1 M2 D, E, F, 2 M3 G, H, I, 3 M4 J, K, L, 4 M5 M, N, O, 5/ Directory DOWN M6 P, Q, R, 6/ Directory UP MODE S, T, U, 7 TUNE DOWN V, W, X, 8 TUNE UP Y, Z, SPACE, 9 SELECT Character shift DSP _, –, +, 0 VOL UP/DOWN CHARACTER SELECT (A, B~Z, SPACE, 0~9, -, +) AS/PS Backspace songs under this directory and select the title.
OPERATION 3. For a non-MP3 file, even though the file name extension is “.MP3”, the unit cannot recognize it. Note: A. Notes on discs: 1. Attempting to use non-standard shape discs (e.g. square, start, heart) may damage the unit. Be sure to use round shape CD discs only for this unit. 2. Do not stick paper or tape, etc, onto the label side or the recording side of any discs, as it may cause a malfunction. 3. Dirt, dust, scratches and warping discs will cause misoperation. B.
CONTROL & FUNCTIONS KEYS 6 5 7 8 1 4 3 2 This unit is a marine rated wired remote control made using a modified controller or similar layout. It is capable of operation specified functions on the marine AM/FM/CD receiver and the marine AM/FM receiver. The body, buttons, controls and display need to be UV and water-resistant. It includes LCD and an illumination circuit. The flat body should be watertight and the circuit board clear coated.
INSTALLATION 6 TRACK/SEARCH/TUNE buttons • STATION SELECTION (FOR RADIO OPERATION) Press / buttons (6) shortly to activate automatic seek function. Press for more than 3 seconds until “MAN” appears on the display, the manual tuning mode is selected. If both buttons have not been pressed for several seconds, they will return to seek tuning mode and “AUTO” appears on the display. • SELECT TRACKS (FOR CD OR CDC OPERATION) Press the / buttons (6) shortly to move to the following track or the previous track.
INSTALLATION Select the proper position to install the remote controller and then cut a hole with the diameter about 88mm. Then use mounting bracket and two screws to install the controller to the board. Be sure to place the rubber washer and rubber ring between the controller and the board.( Please refer to the following picture.
SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls - Bass (at 100 Hz) - Treble (at 10 KHz) Maximum Output Power Current Drain : DC 12 Volts, Negative Ground : 178 (W) x 178 (D) x 50 (H) mm : 10 dB : 10 dB : 4 x 50 Watts : 15 Ampere (max.) CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response : More than 60 dB : More than 50 dB : 40 Hz - 18 KHz RADIO FM 87.5 to 107.9 MHz 10.
TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom No power. Disc cannot be loaded or ejected. Cause Solution The car ignition switch is not on. If the power supply is properly connected to the car accessory circuits, but the engine is not moving, switch the ignition key to “ACC”. The fuse is blown. Replace the fuse. Presence of CD disc inside the player.
