User Manual

eBand Song List Editor Convenient Functions Appendices
Panel Descriptions Play the Guitar with Songs
as Your Backing
NlPtEsItFrDeEnglish
33
Appendices
NS (Noise Suppressor)
This eect reduces the noise and hum picked up by guitar pickups.
Since it suppresses the noise in synchronization with the envelope
of the guitar sound (the way in which the guitar sound decays over
time), it has very little eect on the guitar sound, and does not
harm the natural character of the sound.
Parameter/
Range
Explanation
ON/OFF
OFF, ON Turns the NOISE SUPPRESSOR eect on/o.
THRESHOLD
0–100
Adjust this parameter as appropriate for the volume of
the noise.
If the noise level is high, a higher setting is appropriate.
If the noise level is low, a lower setting is appropriate.
Adjust this value until the decay of the guitar sound is as
natural as possible.
* High settings for the threshold parameter may result
in there being no sound when you play with your
guitar volume turned down.
EQ (Equalizer)
This adjusts the tone as a equalizer. A parametric type is adopted
for the high-middle and low-middle range.
Parameter/
Range
Explanation
ON/OFF
OFF, ON Turns the EQUALIZER eect on/o.
LOW GAIN
-20–+20dB Adjusts the low frequency range tone.
HIGH GAIN
-20–+20dB Adjusts the high frequency range tone.
LEVEL
-20–+20dB Adjusts the overall volume level of the equalizer.
LO-MID FREQ (Low Middle Frequency)
20.0Hz–10.0kHz
Species the center of the frequency range that will be
adjusted by the LO-MID GAIN.
LO-MID Q (Low Middle Q)
0.5–16
Adjusts the width of the area aected by the EQ
centered at the LO-MID FREQ.
Higher values will narrow the area.
LO-MID GAIN (Low Middle Gain)
-20–+20dB Adjusts the low-middle frequency range tone.
HI-MID FREQ (High Middle Frequency)
20.0Hz–10.0kHz
Species the center of the frequency range that will be
adjusted by the HI-MID GAIN.
HI-MID Q (High Middle Q)
0.5–16
Adjusts the width of the area aected by the EQ
centered at the HI-MID FREQ.
Higher values will narrow the area.
HI-MID GAIN (High Middle Gain)
-20–+20dB Adjusts the high-middle frequency range tone.
LOW CUT (Low Cut Filter)
FLAT, 20Hz–
800Hz
This sets the frequency at which the low cut lter begins
to take eect.
When “FLAT” is selected, the low cut lter will have no
eect.
HIGH CUT (High Cut Filter)
630Hz–12.5kHz,
FLAT
This sets the frequency at which the high cut lter
begins to take eect. When “FLAT” is selected, the high
cut lter will have no eect.
MODULATION
Use MOD SELECT to select the eect that you want to use.
Parameter/
Range
Explanation
ON/OFF
OFF, ON Turns the MODULATION eect on/o.
MOD SELECT (Modulation Select)
Select the modulation type.
PHASER Phaser p. 33
FLANGER Flanger p. 34
CHORUS Chorus p. 34
TREMOLO Tremolo p. 34
ROTARY Rotary p. 34
UNI-V Uni-Vibe p. 34
PAN Pan p. 34
PHASER
By adding varied-phase portions to the direct sound, the phaser
eect gives a whooshing, swirling character to the sound.
Parameter/
Range
Explanation
TYPE
Selects the number of stages that the phaser eect will use.
4 STAGE
This is a four-phase eect. A light phaser eect is
obtained.
8 STAGE This is an eight-phase eect. It is a popular phaser eect.
12 STG
This is a twelve-phase eect. A deep phase eect is
obtained.
BI-PH.
This is the phaser with two phase shift circuits
connected in series.
RATE
0–100 (*) This sets the rate of the phaser eect.
DEPTH
0–100 Determines the depth of the phaser eect.
RESONANCE
0–100
Determines the amount of resonance (feedback).
Increasing the value will emphasize the eect, creating
a more unusual sound.
Setting parameters with Tap Tempo
The values for the parameters marked with an asterisk (*) can
be set so they match the timing you use when pressing the
[SPEED] button (Tap Tempo).
Tap the [SPEED] button two or more times in succession to
specify a tempo for the parameter.