Protect the Disc Mechanism Avoid inserting any foreign objects into the slot of this player. Failure to observe this may cause malfunction due to the precise mechanism of this unit. FEATURES Compatible with PAL DVD (Video CD) and NTSC DVD (Video CD) This player can play discs recorded in either PAL or NTSC format. • A single LSI chip now integrates all major DVD playback circuit functions including MPEG2 decoder, video D/A converter, and audio decoders.
CONTENTS Safety Information ......................................................................................................4 Disc Notes...................................................................................................................5 Installation...................................................................................................................6 The Player .................................................................................................................
SAFETY INFORMATION CAUTION: MOBILE DVD PLAYER IS A CLASS I LASER PRODUCT. HOWEVER THIS MOBILE DVD PLAYER USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE MOBILE DVD PLAYER CORRECTLY AS INSTRUCTED. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND - DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
DISC NOTES Disc formats supported by this player Label side up DVD 12 cm disc (Single-sided disc only) Video CD 12 cm disc Do not touch the underside of the disc CD 12 cm disc MP3 12 cm disc Do not bend Handling and Cleaning • Dirt, dust, scratches and warping disc will cause misoperation. • Do not place stickers or make scratches on discs. • Do not warp discs. • A disc should always be kept in its case when not in use to prevent from damage. • Do not place discs in the following places: 1.
INSTALLATION Notes: DIN FRONT-MOUNT (Method A) Installation Opening This unit can be installed in any dashboard having an opening as show below: • Choose the mounting location where the unit will not interfere with the normal driving function of the driver. • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly.
INSTALLATION Dashboard 9. Reconnect the cable to the vehicle battery's negative (-) terminal. Then replace the out trim ring Tabs Removing the unit 1. Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery's negative (-) terminal. 2. Remove the metal strap attached the back of the unit (if attached). 3. Lift the top of the outer trim ring then pull it out to remove it. 4.
INSTALLATION To fasten the unit to the factory radio mounting brackets. 1. Align the screw holes on the bracket with the screw holes on the unit, and then tighten the screws on each side. 2. Fasten with the supplied truss screws (5x5mm) or flush surface screws (4x5mm), depending on the shape of the screw holes in the bracket. Note: (1) The outer trim ring, sleeve and the metal strap are not used for method B installation.
THE PLAYER FRONT VIEW Closed Position 5 21 18 20 19 1 2 23 3 15 6 7 10 12 13 4 14 16 25 Open Position 11 17 8 9 5 1 2 23 3 15 6 7 10 12 13 Remove the front panel: 22 24 9 4 14 16
THE PLAYER 1. (BACK) 14. 2. AV IN 15. DSP 3. (OPEN/CLOSE) 16. ENT 4. (EJECT) 17. SETUP 5. Disc Slot 18. LOC 6. MODE 19. MO/ST 7. VOL +/- 20. BAND 8. + 21. AS/PS 9. - 22. Reset Button /MUT 23. Remote Sensor 11. 7“ COLOR TFT MONITOR 24. Front Panel LED 12. S (Smart MODE) 25. / , / (Cursor Buttons) 10. 13.
ELECTRICAL CONNECTION 2 3 4 5 6 7 8 15 14 13 12 11 10 9 FUSE FR (RED) FL(WHITE) PREAMP OUTPUT ANT(BLACK) RR (RED) YELLOW(SYNC) RL (WHITE) RGB BLUE GREEN (WHITE) RED EXTERNAL REMOTE SENSOR (OPTIONAL) AV-INPUT(BLACK) (RED) 0.
REMOTE CONTROL LOCATION AND FUNCTION OF KEYS 1 2 7 21 34 33 29 22 19 16 17 3 20 18 12 14 11 13 36 4 8 15 9 31 30 24 26 35 32 27 10 23 28 5 25 6 12
REMOTE CONTROL 1. 2. 3. 4. EJECT OP/CL SUBT(BACK) 5. 6. 7. ANG CONS MODE 8. SETUP 9. PROG 10. AUD 11. TITLE(DSP) 12. MENU 13. / , / 14. OK 15. 16. 17. 18. / / / 19. 20. 21. 0 - 9 22. MO/ST (-/--) 23. 24. 25. 26. 27. P/N S-M ZOOM VOL+ GOTO (AUTO) 28. RDM 29. LOC (CLEAR) Press POWER button to turn the unit ON or OFF. Press to eject the disc. Press to open/close the screen display. Changes of the SUBTITLE language on multi-subtitle language DVD disc.
REMOTE CONTROL 30. VOL31. RPT 32. A-B 33. AS/PS(BOOKMK) 34. BAND(PBC) 35. MUTE 36.TV-DVD-AUDIO Press VOL- button to decrease the volume level. Switch the Repeat mode of discs. A-B repeat allows a passage to be repeated continuously. In radio mode, press it to activate Automatic Memory Storing/Program Scanning function. During playback, press to enter bookmark function. In radio mode, press it to select desired band. Changing between PBC ON and PBC OFF on the VCD disc.
REMOTE CONTROL Remote Control Inserting the Battery 1. Open the battery compartment cover. 2. Insert the new batteries. Make sure that the positive and negative terminals of the battery are oriented as indicated. 3. Close the cover Battery: One button cell lithium battery. Using the Remote Control Point the remote control towards the remote control signal receiver on the player front face. Operation angle: About 30 degree in each the direction of the front of the remote sensor.
OPERATION angel upward/downward in small steps or draw the panel in/out to get a desired viewing position. (2)Method B: You can enter the panel setup menu by pressing MENU button on the remote control, then select SETUP, in Setup menu you can select the Panel item to enter the panel setup menu. Press / buttons on the remote control to select Angle or Slide items.
OPERATION Remote Sensor There is a remote sensor on the front panel. You can point the remote control handset to the remote sensor on the front panel and press function keys on the remote control to control the DVD unit. The unit is also connected to an external remote receiver (See the electrical connection diagram above), and the function is the same with the remote sensor on the front panel. Press / buttons on the front panel or on the remote control to adjust the selected item.
OPERATION In EQ menu, use / , / cursor button to change the sound mode. • Setup Menu: In Treble menu, use / to select Freq or Level, use / to adjust the corresponding item. In Wallpaper menu, use / cursor buttons to change the wallpaper among Twinkle/Snowfall/Pillar. In Bass menu, use / cursor button to adjust Freq/Level/Q.Fac. In Clock menu, using / buttons to select the hour and minute. Then using / buttons to change the value of the hour and minute.
OPERATION The operation of Picture menu and Panel menu please refer to the before description. In ZoneCtr menu,you can adjust the the mode of the front or rear speakers. Use / to select front speaker or rear speaker. Use / to change the speaker’s mode. Front mode can be changed among DVD/TV/ AV1/ AV2/ RGB/Tuner. Rear mode can be changed among DVD/ TV/ AV1/ AV2.
OPERATION NOTE (FOR THE UNIT WITH TEL-MUTE AND BRAKE FUNCTION): • When there is an incoming call, the unit will be in mute state, and “TEL MUTE” appears on the screen display. • If the brake wire isn’t connected to the ground wire of the parking brake, the picture will not be shown on the screen in DVD/TV/AV mode for safety purpose. Only the audio will be heard. Skipping Track Press / buttons on the remote control during playback. to skip to next track, and Press to back one track. Note: For some VCD2.
SETUP REPEAT PLAY/ PARAGRAPH REPEAT PLAY Repeat play: When you want to repeat playing the whole disc or a track or a chapter in the disc. 1)Press RPT button repeatedly to select different repeat modes. 2)For different kinds of disc, pressing RPT button has different effects. Chapter Track Title All Off Off bookmark.
SETUP For how to set the program menu, please refer to the operation of the audio files in the media player below. the remote control to delete the highlight file directly. 3) In Photo page, there are three areas: Play list, Preview window and the Edit area in the middle. Note: • After you have programmed the tracks, press PROG button can switch between program play and normal play. • Press or OK button on the remote control or ENT on the front panel to exit the edit interface.
SETUP 4) In Movie page, press or OK button on the remote control ENT button on the front panel to open the highlight folder in the play list or play the corresponding file. Music Photo Movie List 1-14053_2mpeg 2-BB_MPEGYEMANNVYOU.mpe 3-badluck.mpeg NOTE: For audio CD, the play interface and operation is similar with the Music page operation. For details, please refer to the description of Music page above.
SETUP Example: MP3: (1) Press DSP for the first time will display the elapsed time of the disc: 01 : 12 (3) Press DSP for the third time: The message on the screen will be resume: 00 : 00 : 55 DVD (2) Press DSP for the second time will display the clock: 01 : 17 (3) Press DSP for the third time, the massage will resume: MP3 T 01 CD: (1) Press DSP for the first time: REPT ALL (2) Press DSP for the second time will display the elapsed time of the disc: 00 : 02 : 39 (3) Press DSP for the third time will
SETUP 1) 1/17 Item: Title Function: Display the current title number and the total title number; it can skip to the desired title number. Method: / buttons or use numeric buttons to input and confirm with OK button on the remote control or ENT button on the front panel. 2) Item: Angle Function: Display the current angle; it can switch to other angle. Method: / buttons or press ANG button. Item: Sound Function: Display the current sound mode; it can switch between normal and 3D surround effect mode.
SETUP changed. In PBC OFF mode, use numeric buttons to input time and confirm with OK/ENT button. 3) Stereo Item: Audio Function: Display the current audio mode; it can switch to other audio mode. Method: / buttons or press AUD button. 4) • Selecting the frequency band Press BAND on remote control to select desired band. The reception band will change in the following order: Normal FM1 Item: Sound Function: Display the current sound mode; it can switch between normal and 3D surround effect mode.
OPERATION And it will hold at each station for about 5 seconds. - Automatic memory storing Press and hold AS/PS button on remote control for about several seconds or press AS/PS button on the front panel, the radio searches from the current frequency and checks the signal strength until one cycle search is finished. And then stations are stored into the preset number button in turn according to the strength of the stations. When auto search is finished, it will enter into preset scan mode automatically.
SETUP In DVD mode, when the disc is playing or in stop mode, press SETUP on the remote control to enter setup menu. • When the cursor is on the topside, use / buttons to move between the different pages. • Press button to move the cursor to the setup page below and then you can use / buttons to move between the different setup options.
SETUP AUDIO SETUP • When you open the AUDIO menu, you will see the following picture: LOCK SETUP • When you open the LOCK setup page, you will see the following picture. AUDIO LOCK Dolby Digital DTS Sample Freq. Digital Output Bitstream Bitstream 48kHz On Move Rating Password Country Code Unlock New US Select Move • “Dolby Digtial” means the Dolby digital out type. There are “Bitstream” and “PCM” to be selected.
SETUP • “ Country Code” is used to set the country code. The code information standing for original producing area country will be written in every DVD disc when it is produced. There are two characters standing for the name of the country. For example, CN for China, CA for Canada, and so on. Only when the country code you set in the SETUP menu matches with the disc’s own country code, the parent level that you set will come into effect.
TROUBLE SHOOTING If it appears that your DVD unit is faulty, first consult this checklist. It may be that something simple has been overlooked. • Check if the volume is minimum, and adjust the VOL+ to increase the volume level. Under no circumstances should you try to repair the player yourself, as this will invalidate the warranty. Only qualified service personnel can remove the cover or service this player.
SPECIFICATIONS GENERAL Power Supply Requirements : DC 12 Volts, Negative Ground Maximum Output Power : 4 x 80 watts Current Drain : 15 Ampere (max.) TV TV Sensitivity : 45dB V @CH25 in average RADIO Frequency Coverage Sensitivity (S/N = 30 dB) Image Rejection Stereo Separation : : : : FM 87.5 to 107.
SPECIFICATIONS DVD Signal system Discs played : Compositive video 1.0Vp-p 75 Ω : (1) DVD-Video disc 5” (12 cm) single-sided, single-layer 5” (12 cm) single-sided, double-layer (2) Compact disc (CD-DA/CD-R/CD-RW/MP3) (3) (12 cm) VIDEO CD Monitor Screen Size Resolution : 7.0” TFT : 1440 x 234 dots Note: Specifications and design are subject to modification, without notice, due to improvements in technology.
