page CONTENTS In-Dash DVD/MP3/CD 2 Safety Information AM/FM Receiver 3 Installation 6 Wiring Diagram 7 Operation 7 Features and Controls 8 Preparing The Remote Control 9 Using The Detachable Front Panel 9 General Operation It has been designed, engineered 11 Radio Operation and manufactured to bring you the 11 CD/MP3 Operation highest level of performance and 13 DVD/VCD Operation quality, and will afford you years of 17 Data Disc Play Operation listening pleasure.
Safety Information DISC NOTES CAUTION: This mobile DVD player is a class 1 laser product. However this mobile DVD player uses a visible/invisible laser beam which could cause hazardous radiation exposure if directed. Be sure to operate the mobile DVD player correctly as instructed. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Do not open covers and do not repair yourself. Refer servicing to qualified personnel.
Installation Label side up Notes: Do not touch the underside of the disc - Choose the mounting location where the unit will not distract the driver. - Before the installation of unit, connect the Do not bend wiring temporarily and make sure it is all connected up properly and the unit and the system works. - Use only the parts included with the unit to Wipe the disc from center toward the outside edge ensure proper installation. The use of unauthorized parts can cause malfunctions.
Remove Transit Screws Before Installation the appropriate slots at the middle left Before installing the unit, please remove the two screws. sleeve off the back of the unit. and right sides of the unit. Then slide the Take out screws before installation. 1. DIN Front-Mount (Method A) Installation Opening This unit can be installed in any 6.
the supplied hardware (Tapping Screw (5x25mm) and Plain Washer) to attach the other end of the metal strap to a solid metal part of the vehicle under the dashboard. This strap also helps ensure proper electrical grounding of the unit. 2. DIN Rear-Mount (Method B) If your vehicle is a Nissan or Toyota, follow this mounting instruction: Use the screw holes marked T (Toyota), N (Nissan) located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your car. 10.
Wiring Diagram White to Rear L CH RCA output Red to Rear R CH RCA output BV4250 User’s Manual - page 6 Yellow to VIDEO output 2 Yellow to VIDEO output 1 Red to Front R CH RCA output ANTENNA Socket White to Front L CH RCA output Green to SUB-Woofer output Violet Rear Right + Yellow to Battery B+ Violet/Black Rear Right - Black to GND B- Grey Front Right + Red to ACC Grey/Black Front Right - Blue to ANT White Front Left + Green Rear Left + White/Black Front Left - Green/Black Rear Left -
Operation Features and Controls Front Panel : 9 10 5 11 8 2 4 7 SEL 13 19 14 22 1 3 15 16 20 17 6 18 Back of Front Panel: 40 21 12 BV4250 User’s Manual - page 7
Remote control: 9 4 15 6 23 38 22 37 24 36 35 25 26 10 27 - Do not put in a pocket. - Keep away from food, moisture and dirt. - Do not place in direct sunshine. Battery replacement The remote control uses a lithium buttontype battery, model CR2025 3V. Do not use any other kind of battery in the remote. Follow these instructions when installing or replacing the battery. 1. Opening the battery case Slide out the battery cover while firmly pressing in the direction of the arrow.
Using The Detachable Front Panel General Operation Removing the Front Panel Initial System Start-Up Be sure to press the RESET button (12) when using the unit for the first time, after all connections are completed correctly. 1. Turn off the unit power. 2. Press RESET with a ballpoint pen or similar pointed object. 1 . Press the release the front panel . button ( 7 ) on 2 . Pull off the front panel . 3 . Store the front panel in its protective case .
2. Adjusting time: 1). Press DISP button (15) on the unit to show the clock. 2). Repeatedly press SEL button (11) to move to between hour area and minute area. 3). Press VOL+/VOL- (10) to adjust hour or minute. LCD Display Exhibits current information and active functions on the LCD display (8). Remote Sensor Point the remote control handset at the remote IR sensor (2). Press the function keys on the handset to control the system.
Note: If the unit still does not function after you have pressed PRESET, try cleaning the connectors which link the panel and the main housing with a cotton swab moistened with isopropyl (rubbing alcohol). If it still does not work, bring the unit to your dealer for servicing or advice. CD/MP3 Operation Playback 1. Insert a disc with the label side facing up . The disc will be drawn into the player automatically. The information for the current disc will be shown on the screen. 2.
Pause Playback Press button (20) to pause CD/MP3 playback. Press it again to resume playback. Stopping playback - Briefly press the button (31) to stop the playback . W hen the button is pressed and you then press button (20) , normal playback will resume. - Press button (31) twice and then press button to stop the playback and go back to the first track. Fast-Forward / Fast-Reverse 1. Fast-Forward Press button (34) during playback.
DVD/VCD Operation Playback with PBC Menu Some VCD or SVCD discs contain a simplified menu to assist in selection of tracks. To view this menu requires a system called Playback Control (PBC). PBC creates this disc directory “on-thefly” if PBC has been enabled. To turn PBC on, press the PBC button (28). (Please note that PBC does not accommodate the following features: REPEAT, RANDOM, A-B, PROGRAM and GO TO).
REPEAT A-B Then the unit will repeat the playback of the passage you just set from A to B. To revert to normal playback, press A-B button again. REPEAT CANCEL Finding The Beginning of Chapters or Tracks (Files) Use this function to easily move to the beginning of the chapters or tracks (files) on the disc. During playback, p ress button ( 17 ) or button ( 16 ) to skip and play the next or last chapter/track . : Press the button to start playback from the beginning of the next chapter or track (file).
GOTO Function The GO TO function allows you to select a specific place in the program where you want to begin playback. The function is displayed slightly differently between DVD and VCD modes. Press GOTO button (32), the screen will display the following message: FOR DVD: Use the number keys (29) to input the desired Title, Chapter or Time, and then press ENTER button (26) to confirm. FOR VCD: PBC Use the number keys (29) to input the Track and Time then press ENTER button (26) to confirm.
playback. Press ANGLE (35) during playback. The following information will be shown on the screen. ANGLE 1 The angle setting cycles between the available viewing angles recorded on the disc each time the button is pressed. Notes: - The ANGLE function is only available for discs which support it and programs in which these alternate viewing angles have been recorded . - Depending on the disc, the angle may switch in one of two ways. 1 . Seamless: The angle switches smoothly. 2 .
Data Disc Play Operation When you insert a data disc including audio (MP3), movie (MPEG) or picture (JPG) files into the disc slot, the following media play window will be shown on the screen: button to enter into PRE-STOP mode, then press GOTO button (32) to switch back to the reading card mode. Note: While reading the memory card, please don't touch or take out the card. If the player is unable to read the card, please check if the card is in good condition.
Additional Information About Parental Control DVD discs have a parental level assigned to the disc. The range of parental controls is from 1 to 8. In general, this range corresponds to established movie rating systems. Movie rating systems may vary depending on the country you live in. Toward the bottom of this page is a small chart showing the rating system and corresponding Parental Control ratings for the USA. The player can be set in a similar way.
Setup In DVD mode, when the disc is playing or in stop mode, press SETUP button (27) to enter the setup menu. 1. When the cursor is in the upper part of the menu, use the buttons to move between the different pages. 2. Press button to move the cursor to the setup page below. Then you can use the buttons to move between the different setup options. 3. Press or ENTER button to move to the choice list of each setup option , and then use the buttons and the ENTER button to change your selection. 4.
4:3 (LETTER BOX) When you are playing a widescreen format video on a normal (4:3) monitor, the best way to view this is in (4:3) letterbox format. You can see the full picture, but there will be a black band at the top and bottom of the screen. restriction level (1 to 8), and then press ENTER button. 5) When the setting is complete, press SETUP button to return to normal mode.
Audio Setup When you open the AUDIO menu, you will see the following screen: Specification 1. GENERAL Power Supply Requirements DC 12 Volts, Negative Ground Chassis Dimensions 178(W)x160(D)x 50(H) 1) AUDIO OUT: Change among SPDIF/OFF, SPDIF/RAW and SPDIF/PCM. 2) KEY: Change among b,-4, -2, 0, +2, +4, #. Tone Controls - Bass (at 100 Hz) ±10 dB - Treble (at 10 kHz) ±10 dB Maximum Output Power 4x60 watts Current Drain 15 Ampere (max.
Troubleshooting If it appears that your DVD unit is faulty, please first consult this checklist. It may be that something simple has been overlooked. Under no circumstances should you try to repair the player yourself, as this will invalidate the warranty. Only qualified service personnel can remove the cover or service this player. No Power ♦ If the power supply is connected to the car accessory circuits, but the engine is not turned on, switch the ignition key to “ACC”. ♦ Check if the fuse is blown.
