OPERATIONS›PARTS MANUAL MSP445 Mechancial Super Pro (MSP) Series Riding Trowel 053430; 01/11
This manual, or a copy of it, must be kept with the machine at all times. There is a manual storage container located on the machine for your convenience.
Riding Trowel OPERATIONS-PARTS MANUAL This manual covers the Riding Trowel model listed below: Part No. 053300 Description RIDER, MSP445 Copyright © 2011 Allen Engineering Corporation All rights reserved All information, specifications, and illustrations in this manual are subject to change without notice and are based on the latest information at the time of publication.
Limited Warranty LIMITED WARRANTY and LIMITATION OF LIABILITY Allen Engineering Corporation ("Allen") warrants its products to be free of defects in material or workmanship for the following periods: A. New Machines and Parts .......................... One Year B. New Gear Boxes ........................................ Two Years The above listed warranty periods are effective for Allen Machines with a first day of use by End User on April 1, 2007 or later.
Table of Contents Sect No. Title ... ... ... ... ... ... ... ... ... ... Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii Information Contained In This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . .v Dealer Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi Ordering Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents, continued 4.0 ... ... 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 4.11 4.12 4.13 4.14 4.15 4.16 4.17 4.18 4.19 4.20 4.21 4.22 4.23 4.24 4.25 4.26 4.27 4.28 4.29 4.30 4.31 iv Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1 Factory Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2 Replacement Part Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Information Contained in this Manual This manual provides information and procedures to safely operate and maintain the Allen Machine. For your own safety and protection from personal injury, carefully read, understand, and observe the safety instructions described in this manual. Keep this manual or a copy of it with the machine at all times. Always operate this machine in accordance with the instructions described in this manual.
Dealer Information Your Dealer has Allen Engineering Corporation trained mechanics and original Allen replacement parts. Always contact the Allen Dealer who sold you this machine for Allen Certified repairs and replacement parts. Place Allen Dealer information below for future reference.
Ordering Parts Section 4.0 contains illustrated drawings and parts lists for help in ordering replacement parts for your machine. Follow the instructions below when ordering parts to insure prompt and accurate delivery: 1. All orders for service parts - include the serial number for the machine. Shipment will be delayed if this information is not available. 2. Include correct description and part number from the “PARTS” section of this manual. 3.
Model Number - Serial Number Codes Manufacturer’s Codes: When ordering parts or requesting service information, you will always be asked to specify the model and serial numbers of the machine. The legends below specifically defines each significant character or group of characters of the Model Number and Serial Number codes. Model Number MSP 44 5 - 40KO HP & ENGINE MAKE KO = Kohler GASOLINE VERSION MODEL SERIES Serial Number The serial number found on the identification plate is a ten digit format.
Unit Identification Unit Identification Plate Location: An identification plate listing the model number and the serial number is attached to each unit and is located on the rear lower left side of mainframe. Refer to Figure 1 for serial number and model number location. This plate should not be removed at any time. Please record the information found on this plate below so it will be available should the identification plate become lost or damaged.
Technical Specifications Measurements in this manual are in U.S. units and their customary metric units (i.e., metric units contained within brackets [8 mm]). The machine RIGHT-HAND and LEFT-HAND sides are determined by sitting on machine (SOM) facing in the direction the machine will travel when going forward. Machine Features: • Dimensions - NOL (L x W x H) inch [mm] . . . . . . . . . . . . .101.5x50.5x59.5 (guardrings/top of seat) . . . . . . . . . . . . . . . . . . . . . . . . . . .[2578.1x1282.
Technical Specifications, continued • Run Time (Approximate) hr . . . . . . . . . . . . . . . . . . . . . . . .2.5 • Transmission Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Continual Variable Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(CVT) • Drive Belt Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Kevlar Cogged Vee • Hour Meter Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Specifications Engine Information Your MSP445 Riding Trowel mode is equipped with a liquid cooled 40 HP Kohler Gasoline engine. Refer to the applicable engine OEM owner’s manual for specific instructions regarding engine operation. This manual is included with the riding trowel at the time of shipping from AEC. Petrol Engine Features: Max Power @3600 RPM hp (kW) . . . . . . . . . . . . . . . . . . . . .40 (29.8) Displacement cu in (cc) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Machine Dimensional Specifications All information, specifications, and illustrations on this page in this manual are subject to change without notice and are based on the latest information at the time of publication. 59.5 [1511 mm] HEIGHT 101.5 [2578.1 mm] LENGTH 50.5 [1282.
Sound And Vibration Data Sound Pressure Level Information: Sound pressure is "A" weighted . Measured at the operators ear position while the ride-on trowel is operating at full throttle on concrete in a manner most often experienced in “normal ” circumstances. Sound pressure may vary depending upon the condition of the concrete. Hearing protection is always recommended.
Section 1 SAFETY Section 1 SAFETY 053430; 01/11 1-1
Section 1 State Regulations SAFETY CALIFORNIA PROPOSITION 65 WARNING Gasoline engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm.
Federal Regulations Section 1 SAFETY SILICOSIS WARNING Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis.
Section 1 SAFETY 1.1.1 1.1 General Safety Precautions Safety-Alert Signs This manual contains Safety-Alert Signs, as defined below, which must be followed to reduce the possibility of improper service damage to the equipment or personal injury. Read and follow all Safety-Alert Signs included in this manual. NOTE defines an operating procedure, condition, etc. which is essential to highlight that contains useful or important information.
1.2 Spark Arrestor Notice 1.2.1 Section 1 SAFETY Laws Pertaining to Spark Arrestors Some states require that in certain locations arrestors be used on internal combustion engines. A spark arrester is a device designed to prevent the discharge of spark or flames from the engine exhaust. It is often required when operating equipment on forested land to prevent the risk of fires. Consult the engine distributor or local authorities and make sure that you comply with regulations regarding spark arrestors.
Section 1 SAFETY 1.3.1 1.3 Operating Safety Operating Safety Familiarity and proper training are required for the safe operation of this equipment! Equipment operated improperly or by untrained personnel can be dangerous! Read the operating instructions contained in both this manual and the engine manual and familiarize yourself with the location and proper use of all controls. 1.3.2 NEVER operate this machine in applications for which it is not intended. 1.3.
1.3, continued Operating Safety Section 1 SAFETY 1.3.13 ALWAYS close fuel valve on engines equipped with one when machine is not being operated. 1.3.14 ALWAYS store the equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children. 1.3.15 ALWAYS operate the machine with all safety devices and guards in place and in working order.
Section 1 SAFETY 1.4.1 1.4 Engine Safety Engine Safety Internal combustion engines present special hazards during operation and fueling. Read and follow the warning instructions in the engine owner’s manual and the safety guidelines below. Failure to follow the warnings and safety guidelines could result in severe injury or death. 1.4.2 DO NOT run the machine indoors or in an enclosed area such as a deep trench unless adequate ventilation, through such items as exhaust fans or hoses, is provided.
1.5 Service Safety 1.5.1 Section 1 SAFETY Service Safety Poorly maintained equipment can become a safety hazard! In order for the equipment to operate safely and properly over a long period of time, periodic maintenance and occasional repairs are necessary. 1.5.2 DO NOT attempt to clean or service the machine while it is running. Rotating parts can cause severe injury. 1.5.3 DO NOT crank a flooded engine with the spark plug removed on gasoline-powered engines.
Section 1 SAFETY 1.6 Safety and Operation Labels The safety and operation labels shown in this section are placed in important areas on the machine to draw attention to potential safety hazards and service information. Should any of these labels become unreadable or damaged, replacement labels can be odered from your distributor. This is a multi-purpose label that reqiures the operator to have maximum eye, hearing, hand, and feet protection. Also, it highly recommends that the operator reads the manual.
1.6, continued Safety and Operation Labels Section 1 SAFETY This label is a maintenance reminder to grease the thrust bearing daily. This will ensure that the life span of the bearings will be maintained at their optimal preformance level. This label cautions against allowing cleaning agents, surface treatments, or other foreign substances to contaminate drive components. The drive components could be damaged from the contamintates and cause the drive system to fail.
Section 1 SAFETY 1.6, continued Safety and Operation Labels This label warns of the risk hazards associated with engine exhaust fumes causing heath issues as identified by the State of California. This label states that this equipment was proudly manufactured in the United States of America. This label cautions the operator of pinch points on the machine. Most appropriately around the lifting points.
SECTION 2 OPERATIONS Section 2 OPERATIONS 053430; 01/11 2-1
SECTION 2 OPERATIONS This machine is built with user safety in mind. However, it can present hazards if improperly operated and serviced. Follow operating instructions carefully. If you have any questions about operating or servicing this equipment, please contact your Allen Engineering Dealer or AEC Customer Service at 800-643-0095 or 870-236-7751.
2.1 Introduction 2.1.1 SECTION 2 OPERATIONS Description The MSP445 riding trowel is a modern high production machine. Finishing rate will vary depending on the operators skill and job conditions. This riding trowel has ten finishing blades. The Super Heavy Duty (SHD) Gearboxes are designed to provide exceptional performance with low maintenance and trouble free use under some of the worst conditions.
SECTION 2 OPERATIONS 2.9.1 2.2 Start Up Procedures Before Starting Procedures Before starting the riding trowel check for the following: 2.9.2 1) Oil level in engine. 2) Oil level in riding trowel gearboxes. 3) Fuel level in fuel tank. 4) Condition of air filter on engine. 5) Condition of riding trowel arms and blades. 6) Verify that daily maintenance of grease points have been performed. Starting Procedures Before starting riding trowel, refer to Figure 2.2.1 and Figure 2.2.
2.2, continued Start Up Procedures SECTION 2 OPERATIONS IGNITION SWITCH ENGINE CHOKE FIGURE 2.2.1 TOP VIEW OF CONTROLS LIGHT SWITCH HOURMETER FIGURE 2.2.
SECTION 2 OPERATIONS 2.3.1 2.3 Operating Instructions Operating The Riding Trowel To utilize your Allen Engineering MSP445 Rider to its fullest capacity the machine should be driven in the direction the operator is facing. This will finish the widest possible area while giving the operator an excellent view of the slab surface about to be troweled. When the machine reaches the end of the slab make a 180 degree turn and repeat the straight line of direction to the other end of the slab.
2.3, continued Operating Instructions 2) SECTION 2 OPERATIONS With the operator in the seat, show him the functions of the joysticks [B] and [C] and how to start the machine. Refer to Figure 2.3.1. A hard level concrete slab with water on the surface is an ideal place for an operator to practice with the machine. For practice pitch the blades up approximately 1/4 inch on the trailing edge.
SECTION 2 OPERATIONS 2.3.3 2.3, continued Operating Instructions Steering The Riding Trowel A slight "feathering motion" forward and backward with the left hand joystick is required to move the machine in a straight path to the left or right while operating the right hand joystick. Refer to Figure 2.3.3.. Position 1 2 3 4 5 6 Action Forward Reverse Rotate clockwise Rotate counter clockwise Left sideways Right sideways FIGURE 2.3.
2.3, continued Operating Instructions 2.3.4 SECTION 2 OPERATIONS Pitch Adjustment Different pitch angles are needed as you work the different stages of the concrete. Refer to Figure 2.3.4 table below. When changing or setting pitch (angle of trowel blades), slow the machine down, set the desired degree of pitch on the left side of the machine and then adjust the right side to match.
SECTION 2 Notes OPERATIONS 2-10 053430; 01/11
SECTION 3 SERVICE Section 3 SERVICE 053430; 01/11 3-1
SECTION 3 SERVICE 3.1 3.1 Periodic Maintenance Periodic Maintenance Schedule The table below list basic trowel and engine maintenance. Refer to OEM engine manufacturer's Operation Manual for additional information on engine maintenance. A copy of the engine operator's manual was supplied with the machine when it was shipped. To service the engine pull the seat locking pin out and tilt seat back. TABLE 3.1.
3.2 Trowel Gearbox 3.2 SECTION 3 SERVICE Trowel Gearbox Maintenance Check Oil levels in the gearbox daily (every 8 hours) Add oil if oil level is below the check sight glass. 1) To add oil tilt trowel back and remove the fill plug. Add oil through hole opening. Replace fill plug after proper level has been achieved. DO NOT fill past the fill plug hole opening. Use Allen Mobil Oil SHC 634, synthetic ISO VG 460.
SECTION 3 SERVICE 3.3.0 3.3 Drive Belt Drive Belt Maintenance The drive belts MUST be free from oil and foreign contaminants to prolong life. 3.3.1 3.3.2 3-4 To Replace The Drive Belt: 1) The MSP445 is equipped with a spare belt located inside the belt guard. 2) Place the trowel on a flat, level surface with the blades pitched flat. 3) Disconnect the battery. Refer to Figure 3.3.1. 4) Use a M6x1.
3.3, continued Drive Belt SECTION 3 SERVICE REMOVE POSITIVE BATTERY CABLE FIGURE 3.3.
SECTION 3 SERVICE 3.3, continued Drive Belt TORQUE CONVERTER CLUTCH DRIVER PULLEY DRIVEN PULLEY POSITION SPACER TELESCOPING U-JOINT ASSEMBLY COGGED VEE CVT BELT 1/4-20x5/8 SOCKET HEAD RND SCREWS (4X) AND Ø1/4 ID SPLIT LOCK WASHERS (4X) CENTER SHAFT HUB DRIVEN PULLEY FIGURE 3.3.
3.3, continued Drive Belt SECTION 3 SERVICE DRIVEN PULLEY M6x1.0 MM THREADED HOLE M6x1.0x40 MM BOLT FIGURE 3.3.
SECTION 3 SERVICE 3.4 3.4 Control Lever Adjustment Control Lever Adjustment Procedure Be sure that the trowel is on a level surface. The control levers should line up evenly. If levers appear out of adjustment they can be re-adjusted forward or backwards as follows: Trowel must be placed on flat level surface that fully supports the blades on both rotors. 3-8 1) Remove bolts and nuts [A]. 2) Remove jam nuts [B]. 3) Extend linkage to adjust control levers backward.
SECTION 3 3.4, continued Control Lever Adjustment SERVICE [B] [A] [A] [B] [A] FIGURE 3.4.
SECTION 3 SERVICE 3.5 3.5 Right Hand Control Lever Adjust RH Control Lever Adjustment Right Or Left Procedure The right hand lever should be set to the same angle as that of the left to form a "V". If levers become out of adjustment adjust the right hand lever as follows: 3-10 1) Remove jam nuts [D]. 2) Remove bolt [C]. 3) Extend linkage to move control levers to the right . 4) Shorten linkage to move control levers to the left.
3.5, continued Right Hand Control Lever Adjust SECTION 3 SERVICE “V” FORM JOY STICK LOCATIONS FIGURE 3.5.1 “V” FORM ORIENTATION [C] [D] LINKAGE [D] LOWER CONTROL ARM FIGURE 3.5.
SECTION 3 SERVICE 3.6 3.6 Lift Lever Adjustment Lift Lever Adjustment Procedure Damage to and/or replacement of a trowel arm can change the adjustment of the lift lever. This can unbalance the trowel arms and cause the riding trowel to wobble during operation. To operate smoothly the lift lever on all trowel arms must be adjusted the same to ensure that the riding trowel is balanced correctly. Adjusting the trowel arms is accomplished by using the optional trowel arm alignment jig AEC PN 016863.
3.6, continued Lift Lever Adjustment SECTION 3 SERVICE STABLIZER RING [A] TROWEL ARM BLADE FIGURE 3.6.1 PRESSURE PLATE LOCATION [B] SPIDER BOSS FIGURE 3.6.
SECTION 3 SERVICE 3.7 3.7 Transporting Trowel Transporting Trowel Procedures Optional dolly jacks are available for short moves or to aid in servicing the trowel. Install dolly jacks as follows: 1) Inspect dolly jack for serviceability and damage. 2) Place riding trowel on firm level ground. 3) Tie steering levers [I] to frame to prevent them from tipping forward when trowel is being lifted. 4) Insert the front dolly jack [J] fully into the holes [K] in the mainframe of the riding trowel.
SECTION 3 3.7, continued Transporting Trowel [K] [L] FIGURE 3.7.2 FRONT DOLLY JACK PORT LOCATION [J] FIGURE 3.7.4 FRONT DOLLY JACK 053430; 01/11 SERVICE FIGURE 3.7.3 REAR DOLLY JACK LOCATION [M] FIGURE 3.7.
SECTION 3 SERVICE 3.7, continued Transporting Trowel The dolly jack lifting system is designed for short moves and to aid in servicing the trowel. It is not a substitute for a towing system or trailer. An optional lifting bridle [N] is available and recommended for lifting the trowel. Attach the bridle to each of the four lifting eyes [O] on the trowel. Refer to Figure 3.7.7. Secure steering levers to frame to prevent them from tipping forward when the towel is being lifted.
3.7, continued Transporting Trowel SECTION 3 SERVICE LIFTING EYE [O] FIGURE 3.7.
SECTION 3 SERVICE 3.9 3.8 Battery Jump Start Battery Jump Start Procedures Occasionally it may be necessary to jump start a weak battery. If jump starting is necessary the following procedure is recommended to prevent starter damage, battery damage, and personal injury. Jump starting a battery incorrectly can cause the battery to explode resulting in severe personal injury or death. Do not smoke or allow any ignition sources near the battery and do not start a frozen battery.
3.8, continued Battery Jump Start SECTION 3 SERVICE BATTERY FIGURE 3.8.
SECTION 3 SERVICE 3.9.1 3.9 Winterizing Retardant System Why Winterize Retardant System If water is allowed to freeze in the retardant system, serious damage to the hose system and the pump may occur. Failures of this type will void the warranty of the pump. Pump fails to deliver water (wetting agent) to nozzles due to freezing in spray system. The best guarantee against damage is to completely drain the retardant system of all accumulation and/or use of water in system.
3.9, continued Winterizing Retardant System SECTION 3 SERVICE RETARDANT TANK SPRAY PUMP BOTTOM PORT OF RETARDANT TANK FIGURE 3.9.
SECTION 3 Notes SERVICE 3-22 053430; 01/11
Section 4 PARTS Section 4 PARTS 053430; 1/11 4-1
Section 4 Factory Service Information PARTS This section contains the illustrated drawings and parts list for help in identifying and/or ordering replacement parts for your machine. Follow the instructions in the front section of this manual “Ordering Parts” when ordering replacement parts to insure prompt and accurate delivery. The Right Hand (RH) and/or Left Hand (LH) orientations are defined from the operator’s view of sitting on machine (SOM).
Replacement Parts Procedures Section 4 PARTS We recommend AEC quality replacement parts, available from the AEC Customer Service Department or your nearest AEC Dealer. Part numbers are subject to change without notice. Part numbers might be different outside of the United States of America. Use part numbers listed in the applicable parts list table when you place your order.
Section 4 PARTS 4.
4.1 Parts List, Front View Upper Frame Unit DESCRIPTION Section 4 PARTS REF PART NO. QTY NOTES - 048988 MODULE, SEAT FRAME 1 049017 FRAME, SEAT 1 2 049060 SEAT, OPERATOR 1 3 041537 HOLDER, CUP 1 4 049000 SCREEN, FRONT 1 5 048678 HANDLE, LOAD RATED NYLON 1 6 053430 MANUAL, MSP445 MECH DRV OPER/PARTS 1 (1) REF 1 NOTES: 1. Not shown.
Section 4 PARTS 4.
4.2 Parts List, Rear View Upper Frame Unit DESCRIPTION Section 4 PARTS REF PART NO. QTY NOTES 1 010090 WASHER, 5/16 SPLIT LOCK 2 2 010018 BOLT, 5/16-18x1/2 HEX HEAD CAP 2 3 048877 BRACE, 13-1/2 TABLE LEG 1 4 047665 BUMPER, RUBBER 2 5 010568 SCREW, 10-32x1/2 ROUND HEAD MACHINE 3 6 029568 NUT, 10-32 NYLOCK HEX 3 7 010036 BOLT, 3/8-16x1 HEX HEAD CAP 4 1,2 8 010464 NUT, 3/8-16 NYLOCK HEX 4 1,2 NOTES: 1. Not shown. 2.
Section 4 PARTS 4.
4.3 Parts List Instrumentation-Control System REF PART NO. 1 047685 DESCRIPTION METER, HOUR PANEL MOUNT Section 4 PARTS QTY NOTES 1 NOTES: 1. Not shown.
Section 4 PARTS 4.
4.42 Parts List, Front View Lower Frame Unit DESCRIPTION Section 4 PARTS REF PART NO.
Section 4 PARTS 4.
4.5 Parts List, Rear View Lower Frame Unit DESCRIPTION Section 4 PARTS REF PART NO.
Section 4 PARTS 4.
4.6 Parts List Fuel System DESCRIPTION Section 4 PARTS REF PART NO. QTY NOTES 1 047700 TANK, 6 GALLON PLASTIC 1 2 048921 STRAP, TANK 2 3 019430 CLAMP. NO.
4.
4.7 Parts List Electrical System DESCRIPTION Section 4 PARTS REF PART NO.
Section 4 PARTS 4.
4.8 Parts List Steering System DESCRIPTION Section 4 PARTS REF PART NO. QTY NOTES 1 010083 WASHER, 3/8 LOCK 1 1 2 010102 NUT, 3/8-16 HEX 1 1 3 048898 SHAFT, LONG STEERING LINKAGE 1 4 046701 ARM, STEERING 4-1/2 2 5 221408 ROD, END MALE 1/2 4 6 013740 WASHER, NO.
Section 4 4.
4.9 Parts List Redardant Spray System DESCRIPTION Section 4 PARTS REF PART NO. QTY NOTES 1 047700 TANK, 6 GALLON PLASTIC 1 2 048921 STRAP, TANK 2 3 012702 TIP, 80°x0.
4.
4.10 Parts List Pitch Control Assembly DESCRIPTION Section 4 PARTS REF PART NO. QTY NOTES - 032370 ASSY, PITCH CONTROL 2 1 015410 SCREW, 1/4-20x3/8 RND HD MACH 2 2 015747 PIN, 3/16x1-3/8 ROLL 1 3 015768 SCREW, 1/4-20x1/4 SCKT HD CAP 2 4 026240 TUBE, PRO PITCH CONTROL 1 5 029812 BUSHING, SLIDE PITCH CONTROL 1 1 6 029822 SHAFT, PITCH CONTROL 1 1 7 032115 KNOB, PITCH CONTROL HANDLE 1 8 032157 ASSY, CRANK HANDLE AND BEARING 1 1 1 2 NOTES: 1. Not shown. 2.
Section 4 4.
4.11 Parts List Gas Power Unit REF PART NO. 1 053304 DESCRIPTION ASSY, MSP445 POWER UNIT Section 4 PARTS QTY NOTES (1) REF NOTES: 1. Not shown.
Section 4 4.
4.12 Parts List Engine System REF PART NO. 1 053306 DESCRIPTION ENGINE, KOHLER CH-1000 Section 4 PARTS QTY NOTES 1 2 52 050 02-S FILTER, ENGINE OIL 1 2 3 62 083 03-S FILTER, PRE-CLEANER FOAM AIR CLEANER 1 1, 2 4 62 083 04-S FILTER, PRIMARY CARTRIDGE AIRE CLEANER 1 1, 2 5 24 050 13-S FILTER, FUEL 1 1, 2 NOTES: 1. Not shown. 2. Service Part Item.
Section 4 4.
4.13 Parts List Engine Mounting System ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 PART # 010089 010096 015692 015696 017314 017898 020514 033661 039740 046904 047477 047635 047637 047845 048810 048845 053136 053204 053223 053306 053308 053327 053328 053334 053384 053385 053389 Section 4 PARTS DESCRIPTION WSHR, Ø1/4 ID Z-STL SPLIT LOCK FSTN, Ø7/16 ID Y-ZINC HRDND FLAT CAP, Ø1/4 RED GREASE KEY, .25x1.
4.
4.14 Parts List Driveline System ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PART # 010089 010096 015692 015696 017314 017898 046904 047477 047635 047637 047845 048810 048845 053389 DESCRIPTION WSHR, Ø1/4 ID Z-STL SPLIT LOCK FSTN, Ø7/16 ID Y-ZINC HRDND FLAT CAP, Ø1/4 RED GREASE KEY, .25x1.25 LG HARD RAD SHCS, 1/4-20 X 5/8 FSTN, HHCS 7/16-20 X 1-1/2 GR8 BRG, Ø1 BORE 2-HOLE FLNG NUT, 7/16-20 YZ GR 8 STOVER HUB, Ø1 BORE U-JOINT CENTER SHAFT ASSY, U-JOINT TELESCOPING SPCR, 1.
Section 4 PARTS 4.
4.15 Parts List Throttle Control System DESCRIPTION Section 4 PARTS REF PART NO. QTY NOTES 1 032300 ASSY, 60 LG THROTTLE CABLE 1 2 049037 ROD, 10-32 FEMALE END 1 3 013728 SCR, 10-32x3/4 HEX HEAD MACHINE 1 4 029568 NUT, 10-32 NYLOCK HEX 1 5 053385 THROTTLE BRKT 1 6 010019 BOLT, 5/16-18x3/4 GR 5 HHC 2 7 010100 NUT, 5/16-18 HEX 2 NOTES: 1. Not shown.
Section 4 PARTS 4.
4.16 Parts List Oil Drain System REF PART NO. DESCRIPTION 1 053334 ASSY, MSP445 OIL DRAIN 2 001005 OIL, CONOCO M.O. 10W30W Section 4 PARTS QTY NOTES 1 0.8 1,2 NOTES: 1. Not shown. 2. QTY (U/M) is indicated by gallons.
Section 4 PARTS 4-36 4.
4.
Section 4 4.
4.18 Parts List Right Hand 20:1 Rotor Assembly REF PART NO.
Section 4 4.
4.19 Parts List Left Hand 20:1 Rotor Assembly REF PART NO.
Section 4 PARTS 4.
4.20 Parts List Right Hand Spider Assembly REF PART NO.
Section 4 4.
4.21 Parts List Left Hand Spider Assembly REF PART NO.
Section 4 PARTS 4.
4.22 Parts List RH 20:1 Super Heavy Duty Gearbox REF PART NO. DESCRIPTION Section 4 PARTS QTY NOTES (1) REF - 037655 GEARBOX, RH SUPER HEAVY DUTY 1 029143 CASE, SHD GEARBOX 1 2 029144 SHAFT, COUNTER LH SHD 1 3 012953 PLUG, 3/4 NPT BI SQ HD PIPE 2 4 028915-10 SHIM, .010 LGE GEARBOX FLANGE 1 5 029146 KEY, GEARBOX SQ 1/2x2.
4.
4.23 Parts List LH 20:1 Super Heavy Duty Gearbox REF PART NO. DESCRIPTION Section 4 PARTS QTY NOTES (1) REF - 037654 GEARBOX, LH SUPER HEAVY DUTY 1 029143 CASE, SHD GEARBOX 1 2 029145 SHAFT, COUNTER RH SHD 1 3 012953 PLUG, 3/4 NPT BI SQ HD PIPE 2 4 028915-10 SHIM, .010 LGE GEARBOX FLANGE 1 5 029146 KEY, GEARBOX SQ 1/2x2.
Section 4 PARTS 4.
4.24 Parts List, Front View Identification and Marking Decals DESCRIPTION Section 4 PARTS REF PART NO.
4.25 Parts List, Rear View Identification and Marking Decals DESCRIPTION Section 4 PARTS REF PART NO.
4.26 Illustration Section 4 Accessory - Pro Dolly Jack System PARTS 8 9 1 10 1 5 11 4 10 7 DASH NO. -01 FRONT LIFT 1 5 4 3 5 2 1 5 6 3 2 4-54 DASH NO.
4.26 Parts List Accessory - Pro Dolly Jack System DESCRIPTION Section 4 PARTS REF PART NO. QTY NOTES - 027684 SET, PRO DOLLY JACK 1 1 017751 WASHER, 3/8 FLAT 16 2 010133 PIN, 3/16 X 2 COTTER 4 3 015692 CAP, 1/4 RED GREASE 4 4 010464 NUT, 3/8-16 NYLOCK LOCK 8 5 024628 SPACER, DOLLY JACK WHEEL 8 6 026728 ASSEMBLY, REAR DOLLEY TUBE [DASH NO. -02] 2 7 026729 ASSEMBLY, DOLLY JACK TUBE [DASH NO.
Section 4 PARTS 4.
4.27 Parts List Accessory - Non-standard Items REF PART NO. DESCRIPTION 1 2 040904-2 035461 DISC, 1200-5 FLOATING (PAN) BRIDLE, 2500 LB 5 FT SLING LIFT Section 4 PARTS QTY NOTES 2 1 NOTES: 1. Not shown.
Section 4 PARTS 4.
4.28 Parts List Tools - Service REF PART NO. 1 2 016863 045399 DESCRIPTION JIG, TROWEL ARM ALIGNMENT PULLER, SHD 5-ARM SPIDER Section 4 PARTS QTY NOTES 1 1 NOTES: 1. Not shown.
4.
Section 4 4.
PARTS TO P1 1 LEFT SIDE 2 FRONT LAMP P1-W1; RED 16 P1-W2; BRN 16 W1; RED 16 W2; BRN 16 P2-(W4); BRN 16 1 P4 TO RIGHT SIDE REAR LAMP 2 P4-(W5); RED 16 TO LEFT SIDE REAR LAMP P2 W7; RED 16 W8; BRN 16 E1 E2 TO TO LT LT GND SW BUSS P4-(W6); BRN 16 1 2 P2-(W3); RED 16 P3-W1; RED 16 P3-W2; BRN 16 1 2 (W1) (W2) P3 TO RIGHT SIDE FRONT LAMP 053430; 1/11 4-62 4.
INTENTIONALLY BLANK 053430; 01/11
YOUR TOTAL SOURCE FOR CONCRETE EQUIPMENT 053430; 01/11
