WARNING To ensure safety while driving and to comply with laws, drivers should not watch video or operate the video device while driving.
BV7280 OWNER’S MANUAL Mobile Audio/Video System y PLL Synthesizer Stereo Radio y Automatic Memory Storing y RBDS Operation y Full Detachable Panel y Preset Equalization y Memory Card Interface y USB Interface y AV IN interface on the front panel y Remote Control 1
CONTENTS INSTALLATION.................................................................................. 3 USING THE DETACHABLE FRONT PANEL .................................... 6 CONNECTIONS................................................................................. 7 LOCATIONS AND FUNCTION OF THE PLAYER ............................. 8 LOCATIONS AND FUNCTION OF THE REMOTE CONTROL ......... 9 OPERATION ......................................................................................
INSTALLATION Notes: y Choose the mounting location where the unit will not interfere with the normal driving function of the driver. y Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. y Use only the p arts included with the unit to ensure proper inst allation. The use of unauthorized p arts can cause malfunctions.
INSTALLATION (1) Metal Strap; (2) Mounting Bolt; (3) Hex Nut; (4) Spring Washer; (5) Tapping Screw; (6) Plain Washer 10. Reconnect the cable to the vehicle battery’s negative (-) terminal. Then replace the outer trim ring and install the unit’s front panel (see the steps of “To Install the front panel”). (1) Dashboard (2) Tabs 7. Reconnect the wire harness and the antenna and be careful not to pinch any wires or cables. 8. Slide the unit into the sleeve until it locks into place. 9.
INSTALLATION Side View showing Screw Holes marked T, N or S Screw Factory Radio Mounting Bracket Screw Dashboard or Console To fasten the unit to the factory radio mounting brackets. Align the screw holes on the bracket with the screw holes on the unit, and then tighten the screws (5x5mm) on each side. Note: The outer trim ring, sleev e and the metal strap are not used for method B installation.
USING THE DETACHABLE FRONT PANEL Precautions when handling 1. Do not drop the control panel. 2. Do not put pressure on the display or control buttons when detaching or re-installing the control panel. 3. Do not touch the contacts on the control panel or on the main unit body. It may result in poor electrical contact. 4. If any dirt or foreign substances adhered on the contacts, they can be removed with a clean and dry cloth. 5.
WIRING CONNECTION Connector A 1. N.C. 2. BRAKE (PINK) 3. REAR VIEW (BROWN) 4. MEMORY +12V (YELLOW) 5. AUTO ANTENNA OUTPUT (BLUE) 6. N.C. 7. +12V (TO IGNITION KEY) (RED) 8. GROUND (BLACK) Connector B 1. REAR RIGHT SPEAKER (+) (VIOLET) 2. REAR RIGHT SPEAKER (-) (VIOLET/BLACK) 3. FRONT RIGHT SPEAKER (+) (GRAY) 4. FRONT RIGHT SPEAKER (-) (GRAY/BLACK) 5. FRONT LEFT SPEAKER (+) (WHITE) 6. FRONT LEFT SPEAKER (-) (WHITE/BLACK) 7. REAR LEFT SPEAKER (+) (GREEN) 8.
OPERATION LOCATION OF KEYS Open the cover 1. 12. BND/AMS (Release button) 13. EQ/TA 2. Volume knob (when rotated) 14. Push SEL (when pressed) 3. PTY/AF 15. 4. 3.2 inch TFT display 16. MODE 5. 1 17. CLOCK 6. 2 18. USB/SD cover 7. 3 OSD 19. USB interface 8. 4 RPT 20. Memory card interface 9. 5 RDM 21. Remote Sensor 10. 6 SUB-T 22. AV IN jack 11. 23.
LOCATIONS AND FUNCTION OF THE REMOTE CONTROL 9
LOCATIONS AND FUNCTION OF THE REMOTE CONTROL In audio file play mode, press to play all tracks in random order. 10. VOL+/VOLPress to increase/decrease the volume level. 11. AUDIO In video play mode, press shortly to display the audio information of the file. In video play mode, press and hold it to enter into EQ setting, such as POP, CLAS, ROCK and OFF. In radio mode, pressing the button is EQ function. 1. Press it to turn on the unit. When the unit is on, press it to turn the unit off. 2.
LOCATIONS AND FUNCTION OF THE REMOTE CONTROL 21. ZOOM Press to allow the picture to be increased in size. 22. SELECT Press to enter into the system setup menu. 23. SEEK/ SEEK+ Press shortly to skip to the previous/next track. Press and hold it to activate fast reverse/forward function. In radio mode, press it shortly to search the frequency backward/forward manually. Press and hold it to seek the frequency automatically. Preparing the Remote Control Inserting the Batteries 1.
OPERATION BASIC OPERATION ◆ Turn the unit on/off BRIGHTNESS CONTRAST SHARTPNESS COLOR HUE RESET When all the connection is finished, press MUT button on the front panel or on the remote control will turn the unit on. When the unit is on, hold press MUT button or press to turn the unit off.
OPERATION Pressing MUT button on the front panel or MUTE button on the remote control will mute the sound. Press it again will resume the sound. function and some dat a will n ever lose even when power's off. You can press the numerical button 1, 3, 6 on the front panel of the unit in succession then hold press 4 button to clear the power-down memory function and “EEP INNT” will appear.
OPERATION Shortly press again will return to the normal playback. ◆ Multi-subtitle language function (For Video file) Press SUB-T button on the remote control or SUB-T button on the front panel during playback. The corresponding information will be shown on the screen. Each time the button is pressed, the subtitle language changes in the sequential order. Note: The language is different according to the video file. Some files only cont ain one subtitle language.
OPERATION 1) SYSTEM SETUP When you open the setup menu, you will see the system se tup page at first, see below: b) Press / , / cursor buttons on the remote control to select the items you want to program. The items you selected will bec ome highlight. c) Input the number you want to program by numeric buttons (0-9) on the remote control. Use cursor buttons to select PLAY on the bottom of the screen, or press ENTER button on remote control to confirm. And the unit will play the tracks you programmed.
OPERATION 3) AUDIO SETUP When you open the AUDIO menu, you will see the following picture: DIGITAL SETUP OP MODE DYNAMIC RANGE DUAL MONO AUDIO SETUP AUDIO OUT KEY * OP MODE: to set the operating modes for Dolby Digital decoder, there are LINE OUT and RF REMOD to be selected. * DYNAMIC RANGE: you can adjust the dynamic range between OFF, 1/8, 2/8. 3/8, 1/2, 5/8, 3/4, 7/8, full. * DUAL MONO: there are STEREO, MONO L, MONO R and MIX MONO to be selected.
OPERATION FM3, AM1 and AM2 band. The operation is as below: 1) Store in Memory Press and hold desired radio preset buttons (numeric buttons 1~6) on the remote control or on the front p anel for several seconds, the memory icon will be shown display and the current listening station will be stored into the number button.
OPERATION AV IN OPERATION ◆ Local/Distant Press LOC button on the remote control to select between local and distant stations. Local setting for reception of strong station, and a distant setting for reception of weaker stations. On the front panel of the unit, there is an AV IN jack. When you connected the audio/video device from the jack, press MODE button on the remote control or MODE on the front panel to select AV IN mode.
TROUBLE SHOOTING If it appears that your unit is faulty, first consult this checklist. It may be that something simple has been overlooked. Nothing happens when the button are pressed. ¾ An optional unit required to listen to each source is not connected yet. Connect the optional unit correctly. ¾ The computer chip in the unit is not functioning normally. Press the reset button on the housing of the unit. The sound quality is poor or distorted.
SPECIFICATION GENERAL Power Supply Requirements Maximum Output Power Current Drain Monitor Screen Size : DC 12 Volts, Negative Ground : 4x80 watts : 15 Ampere (max.) : 3.2” TFT RADIO FM Frequency Coverage 87.5 to 107.9 MHz (USA) 87.
