Submittal Sheet

BOSHART INDUSTRIES
Telephone: [phone] - Toll Free: 1-800-561-3164
Fax: [phone] - www.boshart.com
STAINLESS STEEL CONSTANT PRESSURE MANIFOLD
Boshart recommends -
Using both Gray Stainless Steel PTFE Tape & Gray Magic Pipe Thread
Compound together for joining stainless steel threaded connections.
• 1" FPT tank port makes this manifold functional with any tank on the market
• 1" FPT ports can be bushed down to match your tank and transducer
• MPT x FPT line connections on both ends for ease of installation
• Two 3/4" FPT ports accommodate a relief valve and a hose bibb
• One 1/4" FPT port accommodates a 2" or 2-1/2" dial 1/4" MPT center back mount gauge
PART NO. TANK IN-LINE TOTAL TRANSDUCER DRAIN/ PRESSURE QUANTITY
CONNECTIONS CONNECTIONS LENGTH PORT RELIEF GAUGE
CTN CASE
PORTS PORT
07M-125SS 1" FPT 1- 1/4" MPT x 1" FPT 11" (1) 1" (2) 3/4" (1) 1/4" 4 24
07M-200SS 1" FPT 2" MPT x 1-1/2" FPT 13-3/4" (1) 1" (2) 3/4" (1) 1/4" 1 12
NO LEAD BRASS CONSTANT PRESSURE MANIFOLD
• Available with 3/4" or 1" FPT tank and transducer ports
• MPT x FPT line connections on both ends for ease of installation
• Two 3/4" FPT ports accommodate a relief valve and a hose bibb
• One 1/4" FPT port accommodates a 2" or 2-1/2" dial 1/4" MPT center back mount gauge
PART NO. TANK LINE TOTAL TRANSDUCER DRAIN/ PRESSURE QUANTITY
CONNECTIONS CONNECTIONS LENGTH PORT RELIEF GAUGE CTN CASE
PORTS PORT
2-07M-125-10NL 1" FPT 1- 1/4" MPT x 1" FPT 13-5/8" (1) 1" (2) 3/4" (1) 1/4" 1 16
2-07M-125NL 3/4" FPT 1- 1/4" MPT x 1" FPT 13-5/8" (1) 3/4" (2) 3/4" (1) 1/4" 1 16
MANIFOLD BRACKET
The bracket allows a manifold to be secured to the brackets with “U” bolts and a small pressure tank inserted
to the manifold. This bracket is interchangeable to allow for two different mounting options. Brackets are steel
with black powder coat finish and are supplied with lag screws, “U” bolts, nylon lock nuts and plastic end caps.
QUANTITY
PART NO. DESCRIPTION CARTON
07M-125-MB For 1-1/4" Manifold 20
07M-200-MB For 2" Manifold 20
SINGLE FLAT BAR MOUNTING BRACKET KIT
This NEW design allows the universal bracket to be installed anywhere a solid mounting structure
exists. The 2” wide one piece zinc plated steel bracket is interchangeable to allow for two different
mounting positions.
Each bracket comes complete with a hardware kit which includes:
• Three (3) 1/4” x 2” stainless steel hex head lag screws to mount on a single wall stud
• Three (3) 1/4” x 2” stainless steel nail in anchors to mount on a concrete wall
• Two (2) stainless steel U-Bolts
• Four (4) 1/4-20 UNC stainless steel nylon insert locking nuts
PART NO. DESCRIPTION QUANTITY
CTN CASE
07MB-125 2" wide x 7-3/4" x 11-3/4" with U-bolt for 1-1/4" Manifold 1 20
07MB-200 2" wide x 7-3/4" x 11-3/4" with U-bolt for 2" Manifold 1 20