IZA 190-HZ IZA 250-LZ ZA 190-HZ ZA 250-LZ FreeSpace ® Integrated Zone Amplifier/Zone Amplifier Installation and Operating Guide Installations- og betjeningsvejledning * * * * * * * * For use by professional installers only Kun beregnet til at anvendes af professionelle installatører Nur zur Verwendung durch einen fachkundigen Monteur Solo apto para instaladores profesionales Réservé à un technicien professionnel L’utilizzo è riservato agli installatori professionisti Uitsluitend bestemd voor professione
Contents Page 2 Installation and Operation pro.Bose.
pro.Bose.
Important Safety Instructions pro.Bose.com This product is intended for installation by professional installers only! This document is intended to provide professional installers with basic installation and safety guidelines for Bose® FreeSpace® amplifiers in typical fixed-installation systems. Please read this document before attempting installation. Warning: All Bose products must be used in accordance with local, state, federal and industry regulations.
pro.Bose.com Important Safety Instructions 1. 2. 3. 4. 5. 6. 7. Read these instructions. Keep these instructions – for future reference. Heed all warnings – on the product and in all product documentation. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Vigtige sikkerhedsinstruktioner pro.Bose.com Dette produkt er kun beregnet til at anvendes af professionelle installatører! Dette dokument har til formål at give professionelle installatører grundlæggende installations- og sikkerhedsretningslinjer for Bose® FreeSpace®forstærkere i typiske systemer med fast installation. Læs venligst dette dokument, inden du forsøger at foretage en installation.
pro.Bose.com Vigtige sikkerhedsinstruktioner 1. 2. 3. 4. 5. 6. 7. Læs disse instruktioner. Gem disse instruktioner – til senere brug. Følg alle advarsler – på produktet og i al produktdokumentation. Følg alle instruktioner. Anvend ikke dette apparat i nærheden af vand. Rengør kun med en tør klud. Undgå at blokere ventilationsåbningerne. Installer i overensstemmelse med producentens instruktioner.
Wichtige Sicherheitshinweise pro.Bose.com Dieses Produkt darf nur von fachkundigen Monteuren installiert werden! Dieses Dokument soll fachkundigen Monteuren grundlegende Installations- und Sicherheitsrichtlinie für Bose® FreeSpace®-Verstärker in typischen Festinstallationssystemen bieten. Bitte lesen Sie dieses Dokument vor der Installation durch. Warnung: Alle Bose-Produkte müssen gemäß den örtlichen und staatlichen Vorschriften sowie gemäß allen Branchenbestimmungen verwendet werden.
pro.Bose.com Wichtige Sicherheitshinweise Wichtige Sicherheitshinweise 1. Lesen Sie die folgenden Anweisungen. 2. Bewahren Sie diese Anweisungen auf – zum späteren Nachschlagen. 3. Beachten Sie alle Warnhinweise – am Produkt und in der gesamten Produktdokumentation. 4. Befolgen Sie alle Anweisungen. 5. Verwenden Sie dieses Gerät nicht in der Nähe von Wasser. 6. Reinigen Sie das Gerät nur mit einem sauberen, trockenen Tuch. 7. Achten Sie darauf, dass die Lüftungsöffnungen nicht blockiert sind.
Instrucciones de seguridad importante pro.Bose.com Solo un instalador profesional deberá montar este producto. Este documento está pensado para ofrecer a los instaladores profesionales instrucciones básicas de instalación y seguridad relacionadas con los amplificadores Bose® FreeSpace® en sistemas típicos de instalaciones fijas. Lea este documento antes de intentar la instalación.
pro.Bose.com Instrucciones de seguridad importante 1. 2. 3. 4. 5. 6. 7. Lea las siguientes instrucciones. Guarde estas instrucciones para consultarlas en el futuro. Respete todas las advertencias que se indican en el producto y en la documentación. Siga todas las instrucciones. No utilice este aparato cerca del agua. Límpielo solo con un trapo seco. No bloquee las aberturas de ventilación. Instálelo siguiendo las instrucciones del fabricante.
Instructions importantes relatives à la sécurité pro.Bose.com L’installation de ce produit est réservée à un technicien professionnel ! Ce document à l’intention des installateurs professionnels contient les directives de pose et de sécurité relatives aux amplificateurs professionnels Bose® FreeSpace® en installation fixe. Lisez attentivement ce document avant l’installation. Avertissement : Tous les produits Bose doivent être utilisés en respectant les réglementations locales et nationales.
pro.Bose.com Instructions importantes relatives à la sécurité 1. 2. 3. 4. 5. 6. 7. Veuillez lire ces instructions. Conservez-les pour toute référence ultérieure. Respectez tous les avertissements qui figurent sur le produit ou dans sa notice d’utilisation. Suivez toutes les instructions. N’utilisez pas cet appareil à proximité d’eau ou d’une source d’humidité. Utilisez uniquement un chiffon sec pour le nettoyage. Ne bloquez jamais les orifices d’aération.
Informazioni importanti sulla sicurezza pro.Bose.com Questo prodotto deve essere installato unicamente da installatori professionisti. Questo documento ha lo scopo di fornire agli installatori professionisti le istruzioni di base per l’installazione e la sicurezza degli amplificatori Bose® FreeSpace® negli impianti convenzionali a installazione fissa. Leggere attentamente il documento prima di procedere all’installazione.
pro.Bose.com Informazioni importanti sulla sicurezza 1. 2. 3. 4. 5. 6. 7. Leggere queste istruzioni. Conservare queste istruzioni come riferimento per il futuro. Osservare tutte le avvertenze riportate sul prodotto e nella relativa documentazione. Seguire tutte le istruzioni. Non utilizzare l’apparecchio in prossimità di acqua. Utilizzare solo un panno asciutto per la pulizia. Non ostruire le aperture di ventilazione. Installare il prodotto in conformità con le istruzioni fornite dal produttore.
Belangrijke veiligheidsinstructies pro.Bose.com Dit product is uitsluitend bestemd voor installatie door professionele installateurs! Dit document is bedoeld om basisrichtlijnen met betrekking tot de installatie en veiligheid te bieden voor professionele installateurs voor Bose® FreeSpace®-versterkers in standaardsystemen voor vaste installatie. Lees dit document door voordat u begint met de installatie.
pro.Bose.com Belangrijke veiligheidsinstructies 1. 2. 3. 4. 5. 6. 7. Lees deze instructies door. Bewaar deze instructies voor toekomstig gebruik. Neem alle waarschuwingen in acht, zowel waarschuwingen op het product als in de documentatie van het product. Volg alle instructies. Gebruik dit apparaat niet in de buurt van water. Reinig het apparaat alleen met een droge doek. De ventilatieopeningen niet blokkeren. Installeren volgens de instructies van de fabrikant.
Viktig säkerhetsanvisningar pro.Bose.com Denna produkt ska endast installeras av välutbildade installatörer. Detta dokument är avsett för professionella installatörer som behöver enkla riktlinjer för installation och säkerhet för Bose® FreeSpace®-förstärkare i vanliga fasta systeminstallationer. Läs igenom dokumentet innan du påbörjar installationen. Varning! Alla Bose-produkter måste användas enligt lokala lagar och bestämmelser.
pro.Bose.com Viktig säkerhetsanvisningar 1. 2. 3. 4. 5. 6. 7. Läs de här anvisningarna. Spara anvisningarna för framtida referens. Var uppmärksam på alla varningar, både på produkten och i all dokumentation. Följ alla anvisningar. Använd inte produkten i närheten av vatten. Rengör endast med en torr trasa. Blockera inte ventilationsöppningarna. Installera produkten i enlighet med tillverkarens anvisningar.
Setup and Operation pro.Bose.
Setup and Operation pro.Bose.com Rear-panel FreeSpace® IZA 190-HZ FS2C/ SE/P FS4CE/SE FRONT MIC MIX FRNT MIC DUCK FreeSpace IZA 250-LZ FLAT FS2C/ SE/P FS4CE/SE Loudspeaker connections Use 22 AWG (0.3 mm2) to 14 AWG (2.0 mm2) size wire only. Making loudspeaker connections (IZA 190-HZ) Note: Loudspeaker connections are the same for the ZA 190-HZ amplifier. Wire the 3-pin Euroblock: Use pins 1 (70V) and 3 (COM) for 70V operation.
Setup and Operation pro.Bose.com Making loudspeaker connections (IZA 250-LZ) Note: Loudspeaker connections are the same for the ZA 250-LZ amplifier. 1. Attach included crimp-on spade lug connectors to loudspeaker wiring. Blue spade lug connectors are compatible with 16-14 AWG wire. Red spade lug connectors are compatible with 22-16 AWG wire. Note: You may need to bend the spade lugs to fit. 2. Make a single loudspeaker connection or connect two loudspeakers in parallel.
pro.Bose.com Setup and Operation Input connections RCA input connections Insert the RCA plugs into the INPUT A or INPUT B connectors. Page input connections The PAGE INPUT is a mic/line input with a trigger contact closure. This input signal is routed to all outputs (including AUX OUT) when the trigger is detected. This is designed for push-to-talk paging microphones and telephone paging systems. See the diagrams below for input wiring configurations. Use the included 4-pin Euroblock.
Setup and Operation pro.Bose.com Mic/Line input connections (Front-panel) The MIC/LINE INPUT connector is designed for use with handheld dynamic microphones and XLR, TRS, or TS ¼" microphone cables. Line-level sources also can be used with this input. See the diagrams below for input wiring configurations. Aux input (Front-panel) The front panel auxiliary stereo line input connector is designed for connecting portable audio devices like MP3 players and laptops. When a 1/8" (3.
pro.Bose.com Setup and Operation Remote Control connections Remote volume and source selection control The amplifier is designed to work with the Volume Control with A/B Select User Interface (PC 041967) accessory. The REMOTE connector on the rear panel of the amplifier is labeled to match the connector on the user interface. Use the included 4-pin Euroblock. Volume Control with A/B Select User Interface See the Bose® Volume Control with A/B Select User Interface install guide for more details.
Setup and Operation pro.Bose.com Setup – Rear-panel controls FreeSpace IZA 190-HZ e w FS2C/ SE/P r FS4CE/SE FRONT MIC MIX t FRNT MIC DUCK q FreeSpace IZA 250-LZ e w FS2C/ SE/P r FS4CE/SE t q . Amplifier mode DIP switches • PAGE/MIC NORMAL – BYPASS MASTER Determines if page input source will follow the master level output or can be set at a fixed output level to ensure announcements are heard.
Setup and Operation pro.Bose.com Operation – Front-panel controls and indicators y q w e r t u i Note: Front-panel controls and indicators are identical on the FreeSpace® IZA 190-HZ amplifier. . OFF/ON switch 3 $ / 1 Turns amplifier on or off. POWER indicator Illuminates blue when amplifier is on. INPUT CLIP indicator Illuminates red whenever input source approaches the threshold value of -3dBFS. If the indicator illuminates frequently, reduce input signal level.
Setup and Operation pro.Bose.com FreeSpace® ZA 190-HZ/250-LZ zone amplifier Contents Feet with pins (4) AC power cord RCA cable Spade lugs (8) (LZ only) 3-pin Euroblock (HZ only) (1) Power cord (1) RCA stereo cable (4) Feet with pins (8) Spade lugs (LZ only) (1) 3-pin Euroblock (HZ only) Front-panel controls and indicators q w Note: Front-panel controls and indicators are identical on the FreeSpace® ZA 190-HZ amplifier. . OFF/ON switch Turns amplifier on or off.
Setup and Operation pro.Bose.com Expanding an IZA system with a ZA amplifier The Bose® FreeSpace® ZA 190-HZ/250-LZ zone amplifier makes system expansion easy. When a system design requires more loudspeakers than the FreeSpace IZA 190-HZ/250-LZ integrated zone amplifier can support, the FreeSpace ZA 190-HZ/250-LZ zone amplifier is available to provide additional output channels.
Installation pro.Bose.com Installation and Placement Importance of proper ventilation For placement of the amplifier, keep the following in mind: • Make sure that air can circulate freely around the amplifier for adequate ventilation. There are vents on the top, bottom, and sides. • Do not cover or block amplifier vents. • Do not enclose amplifier in a small space, such as a cabinet. • Make sure the chassis is protected from heat and kept away from direct heat sources, such as heating vents and radiators.
Installation pro.Bose.com Mounting in standard rack with Rack Mount Kit Accessory An accessory Rack Mount Kit is available from Bose for installing one or two FreeSpace® amplifiers in a standard 19" 1 RU electronics rack. The Rack Mount Kit includes: (2) link brackets (2) short rack ears (1) long rack ear (14) M3 x 0.5, 6 mm length Phillips flat-head machine screws Mounting a single amplifier 1. Attach one short rack ear to one side of the amplifier chassis with three (3) of the included screws. 2.
Installation pro.Bose.com 3. Mount amplifier in a rack with four (4) rack screws and washers (not included). Mounting two amplifiers 1. Remove rear rack ears from both amplifiers where they will meet in the middle. Then place the amplifiers upside-down on a flat, level surface on a protective covering to avoid scratching the top of the chassis. 2. Attach a short rack ear to one side of each amplifier chassis with three (3) included screws.
pro.Bose.com Installation 3. Place the amplifiers side by side and attach the two (2) link brackets to the amplifier chassis with four (4) included screws each. CAUTION: Only use the mounting hardware recommended by the rack manufacturer. 4. Mount amplifier in rack with four (4) rack screws and washers (not included). Using the rear rack ears for strain relief The slots on the rear rack ears can be used to provide strain relief with standard wire ties.
Troubleshooting pro.Bose.com Troubleshooting Problem Solution No power • Turn on power. Blue LED on front-panel will be visible when power is on. • Make sure the power cord is plugged in. • Try a different AC outlet that is working with another piece of equipment. Power is on, but no sound • • • • • • • • • • • • • • Make sure the input source is turned on. Verify that there is an input signal from the source. Check the cable connections from the source to the amplifier.
Specifications pro.Bose.com AC Current Draw and Thermal Dissipation Information IZA 250-LZ, AC Current Draw and Thermal Dissipation Test Signal & Power Level Load Configuration (Note: Both IZA channels driven) Power On, Idling Thermal Dissipation, Max Total Audio Output, W 120VAC 60Hz. Line Current, A 230VAC 50Hz. Line Current, A Watts BTU/hr. kCal/hr. 0 0.23 0.16 37 127 32 1/8th Rated Power IEC65 Bandlimited Pink Noise 8 Ω / Ch 6 0.40 0.
Specifications pro.Bose.com IZA 250-LZ/190-HZ Specifications Power Rating Amplifier Power Model IZA 250-LZ Model IZA 190-HZ 2 x 50 W @ 4 Ω; 2 x 25 W @ 8 Ω 1 x 90 W 70/100V Model IZA 250-LZ Model IZA 190-HZ 40 Hz - 20 kHz (+0/-3 dB, @ 1 W reference 1 kHz) 60 Hz - 20 kHz (+0/-3 dB, @ 1 W reference 1 kHz) ≤0.
Specifications pro.Bose.
Specifications pro.Bose.com ZA 250-LZ/190-HZ Specifications Power Rating Amplifier Power Model ZA 250-LZ Model ZA 190-HZ 2 x 50 W @ 4 Ω; 2 x 25 W @ 8 Ω 1 x 90 W 70/100V Model ZA 250-LZ Model ZA 190-HZ 20 Hz - 20 kHz (+0/-3 dB, @ 1 W reference 1 kHz) 60 Hz - 20 kHz (+0/-3 dB, @ 1 W reference 1 kHz) ≤0.
Specifications pro.Bose.com Physical Rack Space Units Dimensions 1 RU high, half rack wide 11.9" L x 8.4" W x 1.8" H (302 mm x 214 mm x 45 mm) Shipping Weight 250-LZ: 6.4 lb (2.9 kg), 190-HZ: 8.6 lb (3.9 kg) Product Weight 250-LZ: 4.4 lb (2.0 kg), 190-HZ: 6.7 lb (3.
Additional Resources pro.Bose.com Importer Information China Importer: Bose Electronics (Shanghai) Company Limited, Part C, Plant 9, No. 353 North Riying Road, China (Shanghai) Pilot Free Trade Zone EU Importer: Bose Products B.V., Gorslaan 60, 1441 RG Purmerend, The Netherlands Mexico Importer: Bose de México, S. de R.L. de C.V. , Paseo de las Palmas 405-204, Lomas de Chapultepec, 11000 México, D.F. For importer & service information: +5255 (5202) 3545 Taiwan Importer: Bose Taiwan Branch, 9F-A1, No.
© 2019 Bose Corporation. All rights reserved. The Mountain, Framingham, MA 01701-9168 USA PRO.BOSE.COM AM857567 Rev.
