Owner's Manual
Table Of Contents
INSTALLATION
Testing
each
speaker
With the speakers secured
to
your ceiling, you can
make sure the speaker functions properly before you
attach the grille.
CAUTION: Before you turn on your receiver/amplifier,
be sure there
is
no unused speaker cable connected
to
it.
An attached cable that
is
free
at
one end can cause a
short
and
damage your receiver/amplifier.
1.
Turn on the receiver/amplifier and
playa
piece
of
music that
is
familiar
to
you.
2.
Make sure the sound is clear and free
of
static.
Static may indicate that the speaker cable is not
connected properly. Refer
to
the
"CAUTION:" on
page
8.
Note:
To
remove the speaker
and
check the connections,
loosen two
of
the screws that are opposite each other
first.
Use one hand
to
support the speaker as you loosen
the third screw. Continue to support the speaker
and
carefully loosen the final screw.
10
Attaching
the
grille
The grille is designed
to
fit into the slots on
the
rim
of
the speaker and lock into place with a slight clockwise
twist.
1.
Notice the six snaps along the inside
edge
of
the
speaker grille.
2.
Position these snaps below
the
six slots along the
rim
of
the speaker.
Snap
3.
On the rim
of
the speaker, notice the six slots that
the
snaps fit into.
4.
Press the grille
onto
the rim
of
the speaker until you
feel
the
snaps engage and
twist
the
grille slightly
to
lock the snaps securely.
Bose®
logo
Note:
Ifyou find it difficult
to
twist the grille, use rubber
gloves
or place a piece
of
non-slip material over the grille
to improve your grip.
5.
Rotate the Bose logo, as needed,
to
adjust it for
your room layout.
INSTALLATION
Testing
each
speaker
With the speakers secured
to
your ceiling, you can
make sure the speaker functions properly before you
attach the grille.
CAUTION: Before you turn on your receiver/amplifier,
be sure there
is
no unused speaker cable connected
to
it.
An attached cable that
is
free
at
one end can cause a
short
and
damage your receiver/amplifier.
1.
Turn on the receiver/amplifier and
playa
piece
of
music that
is
familiar
to
you.
2.
Make sure the sound is clear and free
of
static.
Static may indicate that the speaker cable is not
connected properly. Refer
to
the
"CAUTION:" on
page
8.
Note:
To
remove the speaker
and
check the connections,
loosen two
of
the screws that are opposite each other
first.
Use one hand
to
support the speaker as you loosen
the third screw. Continue to support the speaker
and
carefully loosen the final screw.
10
Attaching
the
grille
The grille is designed
to
fit into the slots on
the
rim
of
the speaker and lock into place with a slight clockwise
twist.
1.
Notice the six snaps along the inside
edge
of
the
speaker grille.
2.
Position these snaps below
the
six slots along the
rim
of
the speaker.
Snap
3.
On the rim
of
the speaker, notice the six slots that
the
snaps fit into.
4.
Press the grille
onto
the rim
of
the speaker until you
feel
the
snaps engage and
twist
the
grille slightly
to
lock the snaps securely.
Bose®
logo
Note:
Ifyou find it difficult
to
twist the grille, use rubber
gloves
or place a piece
of
non-slip material over the grille
to improve your grip.
5.
Rotate the Bose logo, as needed,
to
adjust it for
your room layout.