Owner's Manual
Table Of Contents
INSTALLATION
Connecting
the
speaker
As you connect the wires, be careful
to
match the
polarity
of
each wire
to
the proper terminal, as
described below. An error here will adversely affect
speaker performance.
1.
Choose the one wire on the cable end that is marked
with a colored collar or other indicator, (which
distinguishes it as the positive
(+)
wire.
2.
Notice the red circle on the exposed end of the
positive
(+)
speaker terminal.
3.
Compress both ends
of
the terminal and fully insert
the bared tip
of
the positive wire into the terminal
opening.
Avoid inserting any insulated part
of
the wire.
4.
Release pressure on the terminal
to
capture the wire.
5.
Insert the other wire into the other terminal, marked
with a black circle on the end
to
indicate it is
negative (-).
CAUTION:
00
not
aI/ow exposed wires to brush against
each other.
This
could damage your speaker
or
your
receiver/amplifier.
Trim
any excess wire
and
reinsert it
as necessary
Positive
(+)
wire
to
positive
(red) terminal
8
Finishing
the
installation
It is important
to
have all
of
your equipment ready and
within easy reach
to
complete this procedure.
Securing
the
speaker
As you lift the speaker, keep the speaker cable above
and
out
of
the way
to
prevent pinching it.
You
may notice a security flange, located on the
upper
edge
of
the speaker, for use where local building
codes
require it.
1.
Use
two
hands
to
hold the edge
of
the
speaker as
you guide it into the ceiling hole.
CAUTION: Be sure
not
to press on the two small drivers
seated on the face
of
the speaker.
Security flange
CAUTION: Be careful
not
to damage
or
remove any
of
the foam gasket material along the edge
of
the speaker.
This
gasket
is
important to the operation
of
the speaker.
INSTALLATION
Connecting
the
speaker
As you connect the wires, be careful
to
match the
polarity
of
each wire
to
the proper terminal, as
described below. An error here will adversely affect
speaker performance.
1.
Choose the one wire on the cable end that is marked
with a colored collar or other indicator, (which
distinguishes it as the positive
(+)
wire.
2.
Notice the red circle on the exposed end of the
positive
(+)
speaker terminal.
3.
Compress both ends
of
the terminal and fully insert
the bared tip
of
the positive wire into the terminal
opening.
Avoid inserting any insulated part
of
the wire.
4.
Release pressure on the terminal
to
capture the wire.
5.
Insert the other wire into the other terminal, marked
with a black circle on the end
to
indicate it is
negative (-).
CAUTION:
00
not
aI/ow exposed wires to brush against
each other.
This
could damage your speaker
or
your
receiver/amplifier.
Trim
any excess wire
and
reinsert it
as necessary
Positive
(+)
wire
to
positive
(red) terminal
8
Finishing
the
installation
It is important
to
have all
of
your equipment ready and
within easy reach
to
complete this procedure.
Securing
the
speaker
As you lift the speaker, keep the speaker cable above
and
out
of
the way
to
prevent pinching it.
You
may notice a security flange, located on the
upper
edge
of
the speaker, for use where local building
codes
require it.
1.
Use
two
hands
to
hold the edge
of
the
speaker as
you guide it into the ceiling hole.
CAUTION: Be sure
not
to press on the two small drivers
seated on the face
of
the speaker.
Security flange
CAUTION: Be careful
not
to damage
or
remove any
of
the foam gasket material along the edge
of
the speaker.
This
gasket
is
important to the operation
of
the speaker.