502®A 402® Series IV 802® Series IV Panaray® Full-Range-Driver Array Loudspeakers Installation Guide
Contents pro.Bose.com Introduction Overview.................................................................................................................................................................................5 Panaray® 802® Series IV loudspeaker dimensions.........................................................................................................6 Panaray® 402® Series IV loudspeaker dimensions.........................................................................................
pro.Bose.com Safety Information Important Safety Instructions These loudspeakers are intended for installation by professional installers only! This document is intended to provide professional installers with basic installation and safety JXLGHOLQHV IRU ORXGVSHDNHUV LQ W\SLFDO ¿[HG LQVWDOODWLRQ V\VWHPV 3OHDVH UHDG WKLV GRFXPHQW EHIRUH DWWHPSWLQJ LQVWDOODWLRQ WARNING: All Bose® SURGXFWV PXVW EH XVHG LQ DFFRUGDQFH ZLWK ORFDO VWDWH IHGHUDO DQG LQGXVWU\ UHJXODWLRQV ,W LV WKH LQVWDOOHU¶V UHVSRQVLELOLW\
Safety Information pro.Bose.
Introduction pro.Bose.com Overview Panaray® sound-reinforcement loudspeakers feature full-range cone transducers in proprietary array configurations that provide exceptional reliability in adverse conditions, while delivering natural vocal clarity. For more than five decades, Bose has been improving the performance of full-range cone transducers to provide unmatched reliability, natural sound quality, and wide coverage patterns.
Introduction pro.Bose.
Introduction pro.Bose.
Introduction pro.Bose.
pro.Bose.com Installation Panaray® 802® Series IV loudspeaker mounting options Panaray® 802® Series IV loudspeaker U-bracket (for indoor or outdoor use) The Bose® 802 Series IV loudspeaker can be mounted on a wall or ceiling using the U-bracket accessory kit (not included). Recommended Tools: 5 mm Allen wrench CAUTION: 802 Series IV loudspeakers weigh 13.6 kg (30 lb). Use caution when lifting to avoid injury and/or damage to the loudspeaker. Do not rest loudspeakers on their grilles. 1.
Installation pro.Bose.com 5. Place the loudspeaker on the bracket. 6. Tilt the loudspeaker to the desired angle and insert the second M8 cap screw on each side of the loudspeaker. Wall mount pitch angles Ceiling mount pitch angles 5.6 Nm (50 in-lb) 7. Using a 5 mm Allen wrench, tighten all four cap screws to 5.6 Newton-meters (50 inch-pounds). 8. Connect field wiring and test loudspeaker operation.
Installation pro.Bose.com WBP-8 wall bracket (for indoor use only) Panaray® 402® Series IV loudspeaker mounting options RMUBRKT1 and WBPWR-50 pan-and-tilt bracket kit M8 x 20 mm (4) For Panaray® 402® loudspeakers M8 x 45 mm (4) For other loudspeakers Flat washers (4) Note: The RMUBRKT1 pan-and-tilt bracket is intended for indoor use only. For outdoor applications, use the WBPWR-50 panand-tilt bracket 1. Remove the lower carriage bolt and separate the front and rear halves of the bracket.
Installation 2. pro.Bose.com Attach the bracket to the wall. Follow the instructions provided with the wall bracket. Choose a position and mounting method consistent with local building codes and regulations. Ensure the mounting surface and the method of attaching the loudspeaker to the surface is structurally capable of supporting the weight of the loudspeaker (7.3 kg (16 lb)). A 10:1 safety weight ratio is recommended. 3.
Installation pro.Bose.com 5. Adjust the pitch and yaw using the specified tightening torque. 11 Nm (8 ft-lb) 30° 9 Nm (7 ft-lb) 25 Nm (18 ft-lb) SB-4 suspension bracket kit (for indoor use only) M8 x 16 mm (2) M8 (2) Attach the bracket to the rear of the 402® loudspeaker. Choose a position and mounting method consistent with local building codes and regulations. M8 x 1.25 x 16 mm 2.3 – 2.
Installation pro.Bose.com Panaray® 502® A loudspeaker mounting options WCB-5 U-bracket kit (for indoor use only) M8 x 12 mm (3) 1. (5) M5 x 10 mm M8 x 20 mm (2) Choose a mounting location that will safely support the weight of the loudspeaker (6.8 kg (15 lb)). Refer to “Guidelines for permanent installation of Bose® Panaray® loudspeakers” on page 3. CAUTION: Choose a position and mounting method consistent with local building codes and regulations.
Installation pro.Bose.com Attach the 502® A loudspeaker to the U-bracket. Rotate the loudspeaker to the desired angle and insert the thumbscrew into the locking bracket. MADE IN USA 4.
Installation pro.Bose.com 2. Remove both screws from the bracket and separate the two pieces. 3. Hold the wall bracket in the mounting location to mark and drill the holes. Use four (4) screws per bracket to attach it to the wall. The loudspeaker can be mounted vertically on a wall (A), angled down from a ceiling (B) or angled out from a wall (C). A 4. B C Mount the speaker plate on the 502® A loudspeaker using four M8 x 16 mm screws. Rotate speaker plate 180° to mount as shown in Step 3A.
Installation pro.Bose.com 5. Mount the loudspeaker on the wall plate. Slide the fin of the speaker bracket into the wall bracket and install the M8 x 25 mm pivot screw, and then the M6 x 25 mm pitch locking screw. M8 X 25 mm M6 X 25 mm 6. Set the pitch and yaw of the loudspeaker. To set the pitch: Loosen the M8 x 25 mm screw, remove the M6 x 25 mm screw, change the angle and re-insert the screw. Tighten both screws. To set the yaw: loosen both screws screw, change the angle and tighten both screws.
Installation pro.Bose.com 1. Remove the screw from the end of the 502® A loudspeaker. 2. Mount the bracket to the loudspeaker. M8 x 1.25 x 12 mm 2.3 – 2.8 Nm (20 – 25 in-lb) 3. Choose a position and mounting method consistent with local building codes and regulations. Actual angles for 502 A with a constant voltage transformer 6.
Installation pro.Bose.com Recommended power amplifiers Selecting the proper amplifier size for a given loudspeaker requires analysis of the transducer long-term (or RMS) power rating, dynamic range of the input-source material (crest factor), desired sound pressure levels, and other factors.
Technical Information pro.Bose.
Technical Information pro.Bose.
Technical Information pro.Bose.
Additional Resources pro.Bose.com Visit us on the web at pro.Bose.com for more information, including specifications, technical literature, product warranty, parts and accessories, and global support contact information.
©2015 Bose Corporation, The Mountain Framingham, MA 01701-9168 USA AM747960 Rev.
Panaray Sound-Reinforcement Loudspeakers ® Full-range cone array loudspeakers for installed applications.
Panaray® Sound-Reinforcement Loudspeakers Panaray sound-reinforcement loudspeakers feature full-range cone transducers in proprietary array configurations that provide exceptional reliability in adverse conditions, while delivering natural vocal clarity. For more than five decades, Bose® has been improving the performance of full-range cone transducers to provide unmatched reliability, natural sound quality, and wide coverage patterns.
Panaray® Sound-Reinforcement Loudspeakers Panaray® Full-Range Cone-Array Loudspeakers Point-Source Acoustics (wide vertical coverage) Column Line Array Acoustics (narrow vertical coverage) Panaray 802® Series IV Panaray 402® Series IV Panaray 502® A Panaray MA12EX Panaray MA12 One of the best-selling soundreinforcement loudspeakers in the world is now in its 4th generation.
Panaray® Loudspeaker Specification Summary Point Source Column Line Array 802 Series IV 402 Series IV 502 A MA12EX MA12 52 Hz - 15 kHz 73 Hz - 15 kHz 103 Hz - 15 kHz 58 Hz - 16 kHz 100 Hz - 16 kHz Coverage Pattern, Horizontal 120° 120° 120° 160° 145° Coverage Pattern, Vertical2 100° 60° 70° 20° 20° 300 W 150 W 200 W 200 W 400 W 123 dB 119 dB 117 dB 119 dB 126 dB yes yes yes yes yes Eight 4.5” cone drivers Four 4.5” cone drivers Five 4.5” cone drivers Twelve 2.
Panaray® Sound-Reinforcement Loudspeakers Optional Accessories Subwoofers ® Floor Monitors RoomMatch RMS215 MB24 / MB24 WR MB12 / MB12 WR Panaray MB4 Panaray 620M Panaray 310M Frequency Range (-10 dB) 40 – 280 Hz 36 – 290 Hz 36 – 290 Hz 35 – 350 Hz 55 Hz - 19 kHz 55 Hz - 19 kHz Coverage Pattern (H x V) omni omni omni omni 120° x 40° 120° x 160° 500 + 500 W 400 + 400 W 400 W 200 W 200 W 100 W 139 dB 135 dB 129 dB 122 dB 119 dB 117 dB High Frequency none none none none
PowerMatch® Configurable Power Amplifiers ControlSpace® Processors Portable PA Systems • First powered portable system with selectable vertical coverage • 1,000-watt modules with built-in mixer and EQ settings • J-position, Reverse-J, C-position, and Straight coverage shapes • 2.
Panaray® Sound-Reinforcement Loudspeakers About Bose Professional About Bose Corporation Professional sound systems demand an uncommon expertise and specialized products. Bose Professional is a dedicated group of engineers, product managers, technical support specialists and customer service teams that are focused on the professional audio markets.
©2015 Bose Corporation.
