AutoDome 700 Series IP PTZ Camera VG5 700 Series en User Manual
AutoDome 700 Series IP PTZ Camera Table of Contents | en 3 Table of Contents 1 Getting Started 5 1.1 Powering On 5 1.2 Establishing AutoDome Control 5 2 Using the AutoDome 700 Series 6 2.1 Overview of Features 6 2.2 System Requirements 6 2.3 Connecting the AutoDome 700 Series to the PC 7 2.4 Configuring the AutoDome 700 Series Camera 8 2.4.1 Changing the Network Settings 8 2.5 The Livepage 10 2.5.1 Entering a Keyboard Control Command 13 2.6 Saving Snapshots 14 2.
en | Table of Contents AutoDome 700 Series IP PTZ Camera 4.22 Camera Settings 33 4.23 Lens Settings 35 4.24 PTZ Settings 36 4.25 Diagnostics 36 4.26 Preposition and Tours 37 4.27 Sectors 38 4.28 Miscellaneous 38 4.29 Logs 38 4.30 Audio 38 4.31 Advanced Mode: Recording 39 4.32 Storage Management 39 4.33 Recording Profiles 41 4.34 Retention Time 42 4.35 Recording Schedule 42 4.36 Recording Status 43 4.37 Advanced Mode: Alarm 44 4.
AutoDome 700 Series IP PTZ Camera 1 Getting Started | en 5 Getting Started Install and wire the AutoDome according to the VG5 AutoDome Installation Manual. A typical system includes an ethernet connection, a video management system, a monitor, and appropriate wiring connections. Please refer to the individual product manuals for complete installation and setup instructions for each of the system components. 1.
2 en | Using the AutoDome 700 Series AutoDome 700 Series IP PTZ Camera Using the AutoDome 700 Series The AutoDome 700 Series transmits PTZ control commands and images over a TCP/IP network. It also allows users to configure the camera display settings, camera operating settings, and to configure the network parameters. The AutoDome 700 Series incorporates a network video server in the IP module.
AutoDome 700 Series IP PTZ Camera Using the AutoDome 700 Series | en 7 If you choose to use a computer running Microsoft Internet Explorer or any of the Bosch software, the computer must conform to the following minimum requirements: – Operating System: Windows XP (Service Pack 3) or Windows 7 (32 or 64 bits) – Processor: Intel Pentium Quad Core, 3.
en | Using the AutoDome 700 Series AutoDome 700 Series IP PTZ Camera NOTICE! You can also use the Bosch Video Client utility to configure the network settings for an AutoDome 700 Series camera. Go to www.boschsecurity.com to download the Configuration Manager software and Operating Manual. 2.4 Configuring the AutoDome 700 Series Camera To operate the camera in your network you must assign it a valid network IP address. The default IP address is 192.168.0.
AutoDome 700 Series IP PTZ Camera Using the AutoDome 700 Series | en 9 Using the AutoDome 700 Series Web Server To configure the camera using the AutoDome 700 Series server, do the following: 1. Set the IP address on the PC to 192.168.0.10 to ensure that the PC and the AutoDome 700 Series are on the same Subnet. 2. Launch Microsoft Internet Explorer and navigate to the following URL: http://192.168.0.
2.5 en | Using the AutoDome 700 Series AutoDome 700 Series IP PTZ Camera The Livepage Once the connection is established, the Web browser displays the Livepage. It shows the live video image on the right of the browser window. Depending on the configuration, various text overlays may be visible on the live video image. Other information may be shown next to live video image on the Livepage.
AutoDome 700 Series IP PTZ Camera Using the AutoDome 700 Series | en 11 Protected AutoDome 700 Series If the AutoDome 700 Series is password protected against unauthorized access, the Web browser displays a corresponding message and prompts you to enter the password when you attempt to access protected areas. NOTICE! An AutoDome 700 Series offers the option to limit the extent of access using various authorization levels (see the AutoDome 700 Series online help ). 1. 2.
en | Using the AutoDome 700 Series AutoDome 700 Series IP PTZ Camera 1. To control a peripheral, click the appropriate controls. 2. Move the mouse cursor over the video image. Additional options for controlling peripherals are displayed with the mouse cursor. 3. To manually pan throughout the image area, move your cursor over any part of the live video. The image area displays a directional arrow ( ), then click and hold the right mouse key to pan the camera.
AutoDome 700 Series IP PTZ Camera 2.5.1 Using the AutoDome 700 Series | en 13 Entering a Keyboard Control Command The Aux Control tab is used to enter keyboard control commands. These commands are composed of a command number plus the appropriate function key (Show Shot, Set Shot Aux On or Aux Off). A valid combination either issues a command to the camera or displays an onscreen menu. Aux Control Tab The Aux Control tab is used to enter pre-programmed keyboard control commands.
2.6 en | Using the AutoDome 700 Series AutoDome 700 Series IP PTZ Camera Saving Snapshots You can save individual images from the video sequence currently shown on the Livepage in JPEG format on your computer's hard drive. The icon for recording single images is only visible if the unit is configured to enable this process. Click the icon. The storage location depends on the configuration of the AutoDome 700 Series. 2.
AutoDome 700 Series IP PTZ Camera 3 VG5 Audio Connections | en 15 VG5 Audio Connections The audio version of the AutoDome 700 Series has one audio input for line signals. The audio signals are transmitted one-way and in-sync with the video signals. As a result, a door intercom system can be connected at the camera location. NOTICE! The line ports of the intercom should be used for transmitting audio signals on the intercom systems. 3.
en | VG5 Audio Connections 3.1.3 AutoDome 700 Series IP PTZ Camera Activating Audio Reception To configure audio via the Web browser, do the following: 1. Open the AutoDome 700 Series Livepage, then click the Settings tab. 2. Click the Camera Settings link from the left pane, then click Miscellaneous. The AutoDome 700 Series displays the Audio settings. 3. Click the Audio radio button to activate audio over IP.
AutoDome 700 Series IP PTZ Camera 3.1.4 VG5 Audio Connections | en 17 Enabling Audio Transmission To transmit audio via the IP connection, do the following: 1. Open the AutoDome 700 Series Livepage, then click the Settings tab. 2. Click Service Settings from the left pane, then click Livepage Configuration. The AutoDome 700 Series displays the Livepage Configuration screen (see Figure 3.2). 3. Click the Transmit Audio radio button to enable for audio. Figure 3.2 Livepage Configuration 3.1.
4 en | Configuring the AutoDome 700 Series AutoDome 700 Series IP PTZ Camera Configuring the AutoDome 700 Series The SETTINGS page provides access to the configuration menu, which contains all the unit's parameters arranged in groups. You can view the current settings by opening one of the configuration screens. You can change the settings by entering new values or by selecting a predefined value from a list field.
AutoDome 700 Series IP PTZ Camera 4.1 Configuring the AutoDome 700 Series | en 19 Basic Mode: Device Access Device name You can give the AutoDome 700 Series a name to make it easier to identify. The name makes the task of administering multiple units in larger video monitoring systems easier, for example using the Bosch Video Management System programs. The device name is used for the remote identification of a unit, in the event of an alarm for example.
en | Configuring the AutoDome 700 Series AutoDome 700 Series IP PTZ Camera Time server IP address The AutoDome 700 Series can receive the time signal from a time server using various time server protocols, and then use it to set the internal clock. The unit polls the time signal automatically once every minute. Enter the IP address of a time server here. Time server type Select the protocol that is supported by the selected time server.
AutoDome 700 Series IP PTZ Camera 4.4 Configuring the AutoDome 700 Series | en 21 Basic Mode: Encoder Non-recording profile You can select a profile for encoding the video signal. You can use this to adapt the video data transmission to the operating environment (for example network structure, bandwidth, data load). Pre-programmed profiles are available, each giving priority to different perspectives. When selecting a profile, details are displayed in the list field.
4.5 en | Configuring the AutoDome 700 Series AutoDome 700 Series IP PTZ Camera Basic Mode: Audio You can set the gain of the audio signals to suit your specific requirements. The current video image is shown in the small window next to the slide controls to help you check the audio source and improve assignments. Your changes are effective immediately. If you connect via Web browser, you must activate the audio transmission on the Livepage Functions page (see Section 2.5 The Livepage, page 10).
AutoDome 700 Series IP PTZ Camera Configuring the AutoDome 700 Series | en 23 CAUTION! Do not use any special characters, for example &, in the name. Special characters are not supported by the system's internal recording management and may therefore result in the Player or Archive Player being unable to play back the recording. You can use the second line for entering additional characters; these can be selected from a table. 1. Click the icon next to the second line.
en | Configuring the AutoDome 700 Series 4.11 AutoDome 700 Series IP PTZ Camera Date/Time Date format Select your required date format. Device date/Device time If there are multiple devices operating in your system or network, it is important to synchronize their internal clocks. For example, it is only possible to identify and correctly evaluate simultaneous recordings when all units are operating on the same time. 1. Enter the current date.
AutoDome 700 Series IP PTZ Camera 4.12 Configuring the AutoDome 700 Series | en 25 Display Stamping Various overlays or “stamps” in the video image provide important supplementary information. These overlays can be enabled individually and are arranged on the image in a clear manner. Camera name stamping This field sets the position of the camera name overlay. It can be displayed at the Top, at the Bottom or at a position of your choice that you can then specify using the Custom option.
en | Configuring the AutoDome 700 Series AutoDome 700 Series IP PTZ Camera Camera OSD Select On to momentarily display camera response information, such as Digital Zoom, Iris open/close, and Focus near/far overlays in the image. Select Off to display no information. 1. Select the desired option from the list. 2. Specify the exact position (Position (XY)). 3. In the Position (XY) fields, enter the values for the desired position.
AutoDome 700 Series IP PTZ Camera 4.15 Configuring the AutoDome 700 Series | en 27 Livepage Functions On this page you can adapt theLivepage functions to your requirements. You can choose from a variety of different options for displaying information and controls. 1. Check the box for the items that are to be made available on the Livepage. The selected items are indicated by a check mark. 2. Check whether the required functions are available on the Livepage.
en | Configuring the AutoDome 700 Series 4.16 AutoDome 700 Series IP PTZ Camera Logging Save event log Check this option to save event messages in a text file on your local computer. You can then view, edit and print this file with any text editor or the standard Office software. File for event log 1. Enter the path for saving the event log here. 2. If necessary, click Browse to find a suitable directory.
AutoDome 700 Series IP PTZ Camera Configuring the AutoDome 700 Series | en 29 Pre-programmed profiles are available, each giving priority to different perspectives. – High resolution 1 Target bit rate: 2000 kbps Maximum bit rate: 4000 kbps Encoding interval: 30.00 ips – High resolution 2 Target bit rate: 1500 kbps Maximum bit rate: 3000 kbps Encoding interval: 30.00 ips – Low bandwidth Target bit rate: 700 kbps Maximum bit rate: 1500 kbps Encoding interval: 30.
en | Configuring the AutoDome 700 Series AutoDome 700 Series IP PTZ Camera Profile name You can enter a new name for the profile here. The name is then displayed in the list of available profiles in the Profile name field. Target data rate You can limit the data rate for the AutoDome 700 Series to optimize utilization of the bandwidth in your network. The target data rate should be set according to the desired picture quality for typical scenes with no excessive motion.
AutoDome 700 Series IP PTZ Camera Configuring the AutoDome 700 Series | en 31 P-frame Quality This setting allows you to adjust the maximum image quality of the P-frames. The basic setting Auto automatically adjusts to the optimum combination of movement and image definition (focus). Alternatively, you can use the slide control to set a value between 9and51. The value 9 represents the best image quality with, if necessary, a lower frame refresh rate depending on the settings for the maximum data rate.
en | Configuring the AutoDome 700 Series AutoDome 700 Series IP PTZ Camera Preview Click the Preview button to open a small static preview window for each stream. To enlarge the preview and view live video, click the 1:1 Live View button. JPEG stream Select the resolution, frame rate, and image quality parameters for the M-JPEG stream. – Frame rate: Select one of the following frame rates: 5, 10, 15, 20, 25, or 30 ips. – Picture quality: his setting allows you to adjust the image quality.
AutoDome 700 Series IP PTZ Camera 4.22 Configuring the AutoDome 700 Series | en 33 Camera Settings White Balance Adjusts the color settings to maintain the quality of the white areas of the image. – ATW: allows the camera to continuously adjust color reproduction. – Indoor: white balance tracking for indoor use. – Outdoor: white balance tracking for outdoor use. – AWB Hold: places the ATW on hold and saves the color settings.
en | Configuring the AutoDome 700 Series – AutoDome 700 Series IP PTZ Camera AutoSensUp: increases camera sensitivity by increasing the integration time on the camera. This is accomplished by integrating the signal from a number of consecutive video frames to reduce signal noise. If you select this option, the AutoDome makes the following change automatically: – Auto Iris: switches to Constant Shutter Adjusts the electronic shutter speed (AES).
AutoDome 700 Series IP PTZ Camera 4.23 Configuring the AutoDome 700 Series | en 35 Lens Settings Auto Focus Continuously adjusts the lens automatically to the correct focus for the sharpest picture. – One Push (default): activates the Auto Focus feature after the camera stops moving. Once focused, Auto Focus is inactive until the camera is moved again. – Auto Focus: Auto Focus is always active. – Manual: Auto Focus is inactive. Focus Polarity – Normal (default): focus controls operate normally.
en | Configuring the AutoDome 700 Series 4.24 AutoDome 700 Series IP PTZ Camera PTZ Settings Auto Pan Speed Continuously pans the camera at a speed between right and left limit settings. Type a value between 1 and 60 (expressed in degrees), inclusive. The default setting is 30. Inactivity Selects the time period the dome must be not controlled until the inactivity event will be executed. – Off (default): camera remains on a current scene indefinitely. – Scene 1: camera returns to Preset 1.
AutoDome 700 Series IP PTZ Camera 4.26 Configuring the AutoDome 700 Series | en 37 Preposition and Tours The AutoDome 700 Series can store up to 99 preset scenes and this section allows you to define the individual scenes and a preposition tour comprised of the defined scenes. You define individual preposition scenes, then use these scenes to define the preposition tour. The tour starts from the lowest scene number in the tour and progresses sequentially to the highest scene number in the tour.
en | Configuring the AutoDome 700 Series 4.27 AutoDome 700 Series IP PTZ Camera Sectors Sector The AutoDome 700 Series pan capability is 360° and is divided into 16 equal sectors. This section allows you to apply a title for each sector and to designate any sectors as a Blanked Sector. To define a title for sectors: 4.28 1. Place the cursor in the input box to the right of the sector number. 2. Type a title for the sector, up to 20 characters long. 3.
AutoDome 700 Series IP PTZ Camera Configuring the AutoDome 700 Series | en 4.31 Advanced Mode: Recording 4.32 Storage Management 39 You can record the images from the AutoDome 700 Series on various local storage media or on an appropriately configured iSCSI system. It is also possible to let the VRM Video Recording Manager control all recording when accessing an iSCSI system. This is an external program for configuring recording tasks for video servers.
en | Configuring the AutoDome 700 Series 1. AutoDome 700 Series IP PTZ Camera In the Recording media section, click the iSCSI Media and Local Media tabs to display the applicable storage media in the overview. 2. In the Storage overview section, double-click the required storage medium, an iSCSI LUN or one of the other available drives. The medium is then added to the Managed storage media list. In the Status column, newly added media are indicated by the status Not active. 3.
AutoDome 700 Series IP PTZ Camera 4.33 Configuring the AutoDome 700 Series | en 41 Recording Profiles You can define up to ten different recording profiles. You will then use these recording profiles in the recording scheduler, where they are linked with the individual days and times (see Section 4.35 Recording Schedule, page 42). NOTICE! You can change or add to the recording profile description on the tabs on the Recording Scheduler page (see Page 42). 1.
en | Configuring the AutoDome 700 Series AutoDome 700 Series IP PTZ Camera Virtual alarm Here you can select the virtual alarm sensors that are to trigger a recording, via RCP+ commands or alarm scripts, for example. NOTICE! For more information, please see the Alarm Task Script Language document and the RCP+ documentation. These documents can be found on the product CD supplied.
AutoDome 700 Series IP PTZ Camera Configuring the AutoDome 700 Series | en 43 Holidays You can define holidays that are not in the standard weekly schedule on which recordings are to apply. This allows you to apply a schedule for Sundays to other days with dates that fall on varying weekdays. 1. Click the Holidays tab. Any days that have already been selected will be shown in the table. 2. 3. Click the Add button. A new window will open. Select the desired date from the calendar.
en | Configuring the AutoDome 700 Series AutoDome 700 Series IP PTZ Camera 4.37 Advanced Mode: Alarm 4.38 Alarm Connections You can select how the AutoDome 700 Series responds to an alarm. In the event of an alarm, the unit can automatically connect to a pre-defined IP address. You can enter up to ten IP addresses to which the AutoDome 700 Series will connect in sequence in the event of an alarm, until a connection is made.
AutoDome 700 Series IP PTZ Camera Configuring the AutoDome 700 Series | en 45 Video transmission If the unit is operated behind a firewall, TCP (HTTP port) should be selected as the transfer protocol. For use in a local network, select UDP. CAUTION! Please note that in some circumstances, a larger bandwidth must be available on the network for additional video images in the event of an alarm, in case Multicast operation is not possible.
en | Configuring the AutoDome 700 Series 4.39 AutoDome 700 Series IP PTZ Camera VCA The AutoDome 700 Series contains an integrated video content analysis (VCA), which can detect and analyze changes in the signal on the basis of image processing. Such changes can be due to movements in the camera's field of view. You can select various VCA configurations and adapt these to your application as required. The Silent MOTION+ configuration is active by default.
AutoDome 700 Series IP PTZ Camera Configuring the AutoDome 700 Series | en 47 Metadata is always created for a video content analysis, unless this was explicitly excluded. Depending on the analysis type selected and the relevant configuration, additional information overlays the video image in the preview window next to the parameter settings. With the MOTION+ analysis type, for example, the sensor fields in which motion is recorded will be marked with rectangles.
en | Configuring the AutoDome 700 Series AutoDome 700 Series IP PTZ Camera Tamper detection You can reveal the tampering of cameras and video cables by means of various options. Run a series of tests at different times of the day and night to ensure that the video sensor is operating as intended. NOTICE! The options for tamper detection can only be set for fixed cameras.
AutoDome 700 Series IP PTZ Camera Configuring the AutoDome 700 Series | en 49 Scene too noisy Activate this function if tampering associated with EMC interference (noisy scene as the result of a strong interference signal in the vicinity of the video lines), as an example, should trigger an alarm. Select Area You can select the image areas in the reference image that are to be monitored. The video image is subdivided into 858 square fields.
en | Configuring the AutoDome 700 Series AutoDome 700 Series IP PTZ Camera Sensitivity You can use this setting to adapt the sensitivity to the sound environment. You can effectively suppress individual signal peaks. A high value represents a high level of sensitivity. Signal Ranges You can exclude particular signal ranges in order to avoid false alarms. For this reason the total signal is divided into 13 tonal ranges (mel scale).
AutoDome 700 Series IP PTZ Camera 4.42 Configuring the AutoDome 700 Series | en 51 Alarm Task Editor CAUTION! Editing scripts on this page overwrites all settings and entries on the other alarm pages. This procedure cannot be reversed. In order to edit this page, you must have programming knowledge and be familiar with the information in the Alarm Task Script Language document.
en | Configuring the AutoDome 700 Series AutoDome 700 Series IP PTZ Camera 4.44 Advanced Mode: Interfaces 4.45 Alarm Inputs Select the type of input for each physical alarm. Select from either N.O. (Normally Open) or N.C. (Normally Closed) and provide an optional name for each input. 4.46 Relay The AutoDome 700 Series incorporates one (1) open collector alarm output. Use the following settings to configure the relay. Idle State Specify either Open or Closed idle state.
AutoDome 700 Series IP PTZ Camera Configuring the AutoDome 700 Series | en 53 Automatic IP assignment If a DHCP server is employed in the network for the dynamic assignment of IP addresses, you can activate acceptance of IP addresses automatically assigned to the AutoDome 700 Series. Certain applications (VIDOS, Bosch Video Management System, Archive Player, Configuration Manager) use the IP address for the unique assignment of the unit.
en | Configuring the AutoDome 700 Series AutoDome 700 Series IP PTZ Camera You can activate and configure encryption of the media data (video and metadata) on the Encryption page (see Section 4.52 Encryption, page 58). RCP+ port 1756 To exchange connection data, you can activate the unsecured RCP+ port 1756. If you want connection data to be transmitted only when encrypted, select the Off option to deactivate the port.
AutoDome 700 Series IP PTZ Camera Configuring the AutoDome 700 Series | en 55 Status The status of the DynDNS function is displayed here for information purposes. You cannot change any of these settings. 4.49 Advanced The settings on this page are used to implement advanced settings for the network. Some changes only take effect after the unit is rebooted. In this case, the Set button changes to Set and Reboot. 1. Make the desired changes. 2. Click the Set and Reboot button.
en | Configuring the AutoDome 700 Series AutoDome 700 Series IP PTZ Camera NTCIP Specifies a set of rules and protocols for organizing, describing and exchanging transportation management information between transportation management applications and transportation equipment such that they interoperate with each other. Select a port for NTCIP and the Address from the appropriate drop-down lists.
AutoDome 700 Series IP PTZ Camera Configuring the AutoDome 700 Series | en 57 NOTICE! Duplication of data places a heavy demand on the unit and can lead to impairment of the image quality under certain circumstances. Port Assign a different port to each data stream if there are simultaneous data streams at the same multicast address. Enter the port address of the required stream here. Streaming Click the checkbox to activate multicast streaming mode for the relevant stream.
en | Configuring the AutoDome 700 Series 4.52 AutoDome 700 Series IP PTZ Camera Encryption A special license, with which you will receive a corresponding activation key, is required to encrypt user data. You can enter the activation key to release the function on the Licenses page (see Section 4.55 Licenses, page 59). 4.53 Advanced Mode: Service 4.54 Maintenance Firmware The AutoDome 700 Series is designed in such a way that its functions and parameters can be updated with firmware.
AutoDome 700 Series IP PTZ Camera Configuring the AutoDome 700 Series | en 59 Configuration You can save configuration data for the AutoDome 700 Series on a computer and then load saved configuration data from a computer to the unit. Upload 1. 2. Enter the full path of the file to upload or click Browse to select the required file. Make certain that the file to be loaded comes from the same unit type as the unit you want to configure. 3. Next, click Upload to begin transferring the file to the unit.
en | Troubleshooting Guide AutoDome 700 Series IP PTZ Camera 5 Troubleshooting Guide 5.1 VG5 AutoDome Operation and Control Problem Solution No video – Check that the Green LED on the AutoDome CPU board is on. This LED indicates video from the camera. If the Green LED is off, then: – Check that the Red LED on the AutoDome CPU board is slowly blinking. This LED indicates power to the AutoDome power supply board and to the CPU Module. Red LED on AutoDome CPU M0.
AutoDome 700 Series IP PTZ Camera 5.2 Troubleshooting Guide | en 61 VG5 700 Series AutoDome Video and Control Problem Solution No Network – Connection Check all network connections – Ensure that the maximum distance between any two Ethernet connections is 100 m (328 ft) or less. Refer to the VG5 AutoDome Installation Manual for more information. If O.K., then: – 5.3 If you are behind a firewall, ensure that the Video Transmission mode is set to UDP. a.
en | Troubleshooting Guide Problem Solution No Audio – AutoDome 700 Series IP PTZ Camera Check the computer receiving the audio from the VG5 AutoDome or from the IP Encoder. – Check the computer’s audio settings. Ensure that the sound levels are at an audible level. – Check the computer’s audio output card and speakers. Play a secondary source of audio on the computer. If you still do not hear audio replace the speakers and try again. If O.K.
AutoDome 700 Series IP PTZ Camera Problem Troubleshooting Guide | en 63 Solution If O.K., then: – Check all network connections. – If the video is clear and contains no distortion, then the network connections are probably not the source of audio problems. – Ensure that the maximum distance between any two Ethernet connections is 100 m (328 ft). Refer to the VG5 AutoDome Installation Manual for more information.
en | User Command Table 6 Locked Y AutoDome 700 Series IP PTZ Camera User Command Table Alarm Rule Output Function Key Comm No.
AutoDome 700 Series IP PTZ Camera Index | en 65 Index Symbols D /reset 9 date 24 date format 24 daylight saving time 24 default profile 31 default recording profile 41 default VCA profile 46 deleting recordings 40 device ID 22 device name 19 DHCP server 20 Dibos 6 DirectX 7 Display stamping 10 display stamping 25 displaying on-screen menus 13 dual streaming 6, 28 DynDNS 54 A activating the recording 43 activation key 59 alarm 25 alarm e-mail 50 alarm message 25 alarm rule 51 alarm sensors 41 audio ac
en | Index AutoDome 700 Series IP PTZ Camera I N identification 19 IEEE 802.
AutoDome 700 Series IP PTZ Camera Index | en 67 S saving event log 28 saving system log 28 savng configuration 59 select area 47, 49 selecting a profile 28 sensor fields 47, 49 Set Shot 13 Show Shot command 13 SMS 50 snapshots 6, 14 SNMP 55 SNTP server 20, 24 software DirectX 7 SSL certificate 59 SSL encryption 45 standard recording profile values 41 storage media 39 storage medium 22, 39 streaming 57 subnet mask 8, 20, 53 summer time 24 synchronize 19, 24 system log 12, 27, 28 T tamper detection 48 tar
en | Index F.01U.215.777 | 1.0 | 2011.07 AutoDome 700 Series IP PTZ Camera User Manual Bosch Security Systems, Inc.
AutoDome 700 Series IP PTZ Camera Bosch Security Systems, Inc. Index | en User Manual 69 F.01U.215.777 | 1.0 | 2011.
en | Index F.01U.215.777 | 1.0 | 2011.07 AutoDome 700 Series IP PTZ Camera User Manual Bosch Security Systems, Inc.
AutoDome 700 Series IP PTZ Camera Bosch Security Systems, Inc. Index | en User Manual 71 F.01U.215.777 | 1.0 | 2011.
en | Index F.01U.215.777 | 1.0 | 2011.07 AutoDome 700 Series IP PTZ Camera User Manual Bosch Security Systems, Inc.
Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, PA 17601 U.S.A. www.boschsecurity.com © Bosch Security Systems, Inc.
