AutoDome 100 Series Fixed Camera AutoDome 100 Series en Installation Manual
AutoDome 100 Series Fixed Camera Table of Contents | en 3 Table of Contents 1 Safety 6 1.1 Important Safety Instructions 6 1.2 Safety Precautions 8 1.3 Important Notices 1.4 Customer Support and Service 8 12 2 Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts 13 2.1 Unpacking 13 2.1.1 Parts List 13 2.1.2 Description 14 2.1.3 Tools Required 14 2.2 Pre-installation Checklist 14 2.3 Mount Power Supply Box 15 2.4 Route Wires and Attach Connectors 16 2.4.
en | Table of Contents 4 AutoDome 100 Series Fixed Camera Installing the In-Ceiling Mount 52 4.1 Unpacking 52 4.1.1 Parts List 52 4.1.2 Description 52 4.1.3 Tools Required 52 4.2 Pre-installation Check List 52 4.3 Dimensions 53 4.4 Prepare Drywall Ceiling for Installation 53 4.5 Prepare Suspension Ceiling for Installation 54 4.6 Wire the Interface Box 55 4.6.1 Make the Connections 56 4.6.2 Interface Box Connections 57 4.7 Attach Housing to the Interface Box 58 4.
AutoDome 100 Series Fixed Camera 6 Table of Contents | en 5 Alarms and Relay Connections 69 6.1 Alarm Inputs 69 6.2 Configuring Supervised Alarms (inputs 1 and 2) 69 6.2.1 Configuring a Normally Open Supervised Alarm 69 6.2.2 Configuring a Normally Closed Supervised Alarm 70 6.3 Configuring Non-supervised Alarms (inputs 1 through 7) 70 6.3.1 Configuring a Normally Open Non-supervised Alarm 71 6.3.2 Configuring a Normally Closed Non-supervised Alarm 71 6.4 Alarm Outputs 72 6.4.
en | Safety AutoDome 100 Series Fixed Camera 1 Safety 1.1 Important Safety Instructions Read, follow, and retain for future reference all of the following safety instructions. Heed all warnings on the unit and in the operating instructions before operating the unit. 1. Cleaning - Unplug the unit from the outlet before cleaning. Follow any instructions provided with the unit. Generally, using a dry cloth for cleaning is sufficient, but a moist fluff-free cloth or leather shammy may also be used.
AutoDome 100 Series Fixed Camera Safety | en 7 11. Power sources - Operate the unit only from the type of power source indicated on the label. Before proceeding, be sure to disconnect the power from the cable to be installed into the unit. – For battery powered units, refer to the operating instructions. – For external power supplied units, use only the recommended or approved power supplies. – For limited power source units, this power source must comply with EN60950.
1.2 en | Safety AutoDome 100 Series Fixed Camera Safety Precautions DANGER! This symbol indicates an imminently hazardous situation such as “Dangerous Voltage” inside the product. If not avoided, this will result in an electrical shock, serious bodily injury, or death. WARNING! Indicates a potentially hazardous situation. If not avoided, this could result in serious bodily injury or death. CAUTION! Indicates a potentially hazardous situation.
AutoDome 100 Series Fixed Camera Safety | en 9 Coax grounding: – Ground the cable system if connecting an outside cable system to the unit. – Connect outdoor equipment to the unit's inputs only after this unit has had its grounding plug connected to a grounded outlet or its ground terminal is properly connected to a ground source. – Disconnect the unit's input connectors from outdoor equipment before disconnecting the grounding plug or grounding terminal.
en | Safety AutoDome 100 Series Fixed Camera PoE - Never supply power via the Ethernet connection (PoE) when power is already supplied via the power connector. Power disconnect - Units have power supplied whenever the power cord is inserted into the power source. The power cord is the main power disconnect for all units. Power lines - Do not locate the camera near overhead power lines, power circuits, or electrical lights, nor where it may contact such power lines, circuits, or lights.
AutoDome 100 Series Fixed Camera Safety | en 11 INFORMATIONS FCC ET ICES (commercial applications) (modèles utilisés aux États-Unis et au Canada uniquement, CLASSE A) Ce produit est conforme aux normes FCC partie 15.
1.4 en | Safety AutoDome 100 Series Fixed Camera Customer Support and Service If this unit needs service, contact the nearest Bosch Security Systems Service Center for authorization to return and shipping instructions. Service Centers USA Telephone: 800-366-2283 or 585-340-4162 Fax: 800-366-1329 Email: cctv.repair@us.bosch.com Customer Service Telephone: 888-289-0096 Fax: 585-223-9180 Email: security.sales@us.bosch.
AutoDome 100 Series Fixed Camera Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en 2 Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts 2.1 Unpacking 13 This equipment should be unpacked and handled with care. If an item appears to have been damaged in shipment, notify the shipper immediately. Verify that all the parts listed in the Parts List below are included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative.
en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts 2.1.2 AutoDome 100 Series Fixed Camera Description Chapter 2 details how to install an AutoDome Pendant Arm to a wall, a corner, or to a mast (pole). Any variations to the installation procedures are noted. Refer to Section 3 Installing Roof Parapet and Pipe Mounts for a Roof (Parapet) or Pipe mount installation or Section 4 Installing the In-Ceiling Mount for an In-Ceiling mount installation. 2.1.
AutoDome 100 Series Fixed Camera 6. Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en 15 Choose the appropriate mounting kit to use, depending on the location of the AutoDome, either wall mount, corner mount, or mast (pole) mount. If you application contains a Power Supply Box, refer to Section 2.3 Mount Power Supply Box, page 15. If you are using the Mounting Plate with a 24 V VG5 AutoDome, refer to Section 2.8 Installing the VG4-A-ARMPLATE, page 26.
en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts 4. AutoDome 100 Series Fixed Camera Secure the Power Supply Box to the mounting surface. – For a Wall installation: Use four (4) corrosion-resistant, stainless steel studs (not – For a Corner installation: Secure the Corner Plate to the wall corner using four (4) supplied). Then proceed to Step 5 below. studs (not included). Then proceed to Step 5 below.
AutoDome 100 Series Fixed Camera 17 J101 XF103 Make the Connections DOME HTR 24 VAC 54321 XF101 J102 P107 2.4.1 Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en NC 24V P106 GND TXD RXD Figure 2.2 1. J103 (LED) 24V P105 C+ C- GND TXD RXD XF102 P101 C+ C- Pendant Arm Power Supply Box Route all video, control, and alarm wires through the conduit fitting on the right side of the power box.
en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts 6. AutoDome 100 Series Fixed Camera Attach a BNC connector to the incoming video coax cable. If using UTP for video attach an RJ45 plug to the incoming UTP cable. If installing a Fiber Optic model, attach an ST fiber plug to the optic fiber cable. Refer to Section 5 Cable and Wire Standards, page 61, for the different methods of transmitting video and control protocols, and wire specifications.
AutoDome 100 Series Fixed Camera 2.4.2 Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en 19 Power Supply Box Connections The following figure is a detailed illustration of the Pendant Arm Power Supply Box, which includes the fuse specifications. XF103 XF102 a NC 24V 123 P106 GND TXD RXD P105 C+ C- 6 5 4 3 2 1 Figure 2.
en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts AutoDome 100 Series Fixed Camera The following table lists the Power Supply Box connectors: No. Connector Pin 1 Pin 2 Pin 3 Ground Grounding Screw P101 115/230 VAC or Line NC Neutral Pin 4 Pin 5 Pin 6 24 VAC Power In P105 P106 P107 Table 2.1 2.
AutoDome 100 Series Fixed Camera Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en 21 To properly wire the incoming high voltage and the outgoing low voltage lines, refer to this table: No. Connector Pin 1 Ground Grounding Screw P101 115/230 VAC Power In Line P107 24 VAC Power Out Table 2.2 1.
en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts 6. AutoDome 100 Series Fixed Camera Route the 24 VAC outgoing power supply wires into the VG4-PA0 power supply box through the conduit fitting on the left side of the box. 7. Cut and trim the 24 VAC power and ground wires with sufficient slack to reach their connector terminal in the box, but not so long as to be pinched by or to obstruct closing the cover door. 8.
AutoDome 100 Series Fixed Camera 2.6 Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en 23 Attach Pendant Arm to Power Supply Box The bottom hinge pin of the Pendant Arm is provided with a Hinge Pin Stop to hold the hinge open while attaching the arm to the Power Supply Box. 1. Compress the bottom hinge pin by pushing the pin lever downward and rotating it behind the Hinge Pin Stop. Figure 2.9 Pendant Arm to Power Box Hinge Alignment 2.
2.7 en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts AutoDome 100 Series Fixed Camera Make Connections in Power Supply Box Refer to Table 2.2, Page 21 to locate the various connectors in the power supply box and make the following connections detailed below. 123 Figure 2.10 1. Pendant Arm connections to Power Supply Box Attach the earth ground wire (item 1 in the illustration above) to the grounding screw on the left side of the power box. 2.
AutoDome 100 Series Fixed Camera 4. Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en 25 Connect the 5-pin, 24 VAC to Dome Plug from the Pendant Connector Harness to its corresponding color mating connector P107 on the right side of the box. 5. Connect the BNC plug to the BNC connector from the Pendant Connector Harness and slide its plastic cover over the connection. 6.
en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts 9. AutoDome 100 Series Fixed Camera If using UTP for video, connect the incoming RJ45 video connector, installed previously, to its mating connector from the Pendant Connector Harness. Refer to Section 5 Cable and Wire Standards, page 61 for connections and specifications. 10. Attach the grounding strap of the Pendant Arm to the Power Supply Box. Refer to Figure 2.10, Page 24. 11.
AutoDome 100 Series Fixed Camera d. Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en 27 Once the Mounting Plate (item 1, below) is attached to the Mast Plate (item 2), connect the right angle conduit (item 3) to the Mounting Plate through the empty conduit hole as shown below: 3. 2.8.1 Ensure that the mounting plate is secure.
en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts 2. AutoDome 100 Series Fixed Camera Open the top hinge by pushing its pin lever up and holding it. Note: Both Hinge Pins must be fully compressed to open (unlock) the hinges of the Pendant Arm and before proceeding to the next step. 3. While continuing to hold the top hinge pin open, align the top and bottom hinges of the Pendant Arm to their mating points on the Mounting Plate. Refer to Figure 2.12, above, for an illustration.
AutoDome 100 Series Fixed Camera 1. Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en 29 Route all incoming wires through one of the conduits at the bottom of the Mounting Plate. For a mast mount, route all wires through the right-angle conduit. 2. 3. Attach the water-tight plug to the other conduit. Attach the grounding spade terminal (item 1, below) to one of the spade terminals inside the Mounting Plate. Figure 2.14 Ref. 1 2 3 4.
en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts AutoDome 100 Series Fixed Camera 11. If using UTP for video, connect the incoming RJ45 video connector, installed previously, to the UTP Video/Ethernet cable (cable 5). Refer to Section 5 Cable and Wire Standards, page 61, for detailed wire and connection information. 12. Connect the outgoing alarm wires to the flying leads coming from the 4-pin Alarm Outputs cable (cable 6). 13.
AutoDome 100 Series Fixed Camera 2.9 Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en 31 Attach Pendant to Arm and Tighten NOTICE! Before attaching the AutoDome Pendant, visually inspect the dome and arm connectors for any blocked pin holes or bent pins. 1. Tilt the bottom of the dome toward the pendant arm base and place the mounting hook, located on top of the dome housing, over the recessed hinge pin of the arm. a b Figure 2.15 1 2 2a 2b 3 4 Attach Pendant to Arm Tilt up.
en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts 2. AutoDome 100 Series Fixed Camera Drop the dome housing down slightly to engage the dome housing hook on the Pendant Arm hinge pin, allowing the dome to rotate around the pin. 3. Rotate the dome housing down to a vertical position and gently push upward to engage the connector on top of the dome housing.
AutoDome 100 Series Fixed Camera Installing Roof Parapet and Pipe Mounts | en 3 Installing Roof Parapet and Pipe Mounts 3.1 Unpacking 33 This equipment should be unpacked and handled with care. If an item appears to have been damaged in shipment, notify the shipper immediately. Verify that all the parts listed in the product's Parts List below are included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative. Refer to Section 1.
en | Installing Roof Parapet and Pipe Mounts 3.1.3 Tools Required – 3.2 AutoDome 100 Series Fixed Camera 5 mm Allen wrench (supplied) – Small straight blade screwdrivers ~ 2.5 mm (0.1 in.) – 3.1 mm (1/8 in.) – Medium straight blade screwdriver – No. 1 and No. 2 Phillips screwdrivers – Socket wrench and 9/16 in. socket – Pipe Wrench – Barrel connector (if installing a fiber optic model) Pre-installation Check List 1.
AutoDome 100 Series Fixed Camera 3.3 Installing Roof Parapet and Pipe Mounts | en 35 Mount Power Supply Box Before mounting the Power Supply Box decide if you will be wiring the box through the holes in the bottom or back of the box. If wiring the box through the back, move the two (2) seal plugs to the bottom holes before mounting. NOTICE! Use 3/4-inch NPS (20-mm) fittings for the holes on the bottom and back of the box. Use 1/2inch NPS (15-mm) fittings for the side holes. Refer to Section 3.1.
en | Installing Roof Parapet and Pipe Mounts 3.3.1 AutoDome 100 Series Fixed Camera Attach Cover Door 1. Compress the bottom hinge pin by pushing the pin lever down and then rotate it behind the Hinge Pin Stop. The power box Cover Door provides a Hinge Pin Stop to hold the bottom hinge open while attaching the door. (FUSE) o (FUSE) HTR (FUSE) DOME 90 24V NC 24V GND TXD RXD Figure 3.2 1 2 3 4 2.
AutoDome 100 Series Fixed Camera 3.4 Installing Roof Parapet and Pipe Mounts | en 37 Route Wires and Attach Connectors Power wires must be routed to the left (front) side of the Power Supply Box through a separate conduit. All video, control, and alarm wires must be routed through a second conduit to the right side of the box. Refer to Section 5 Cable and Wire Standards, page 61 for methods of transmitting video and data, and for wire specifications.
en | Installing Roof Parapet and Pipe Mounts – AutoDome 100 Series Fixed Camera The second method is to bypass the Power Supply Box and route the video, control, and alarm wires directly to the Interface Board. You connect only the power wires inside the Power Supply Box.
AutoDome 100 Series Fixed Camera 3.4.2 Installing Roof Parapet and Pipe Mounts | en 39 Wiring the Power Supply Box 1. Route the high voltage 115/230 VAC lines through the conduit fitting on the left side of the box. NOTICE! The Power Supply Box with transformer comes with a barrier that separates the high voltage side on the left from the low voltage 24 VAC side on the right. 2.
en | Installing Roof Parapet and Pipe Mounts AutoDome 100 Series Fixed Camera (FUSE) (FUSE) HTR (FUSE) DOME (GND) 24V NC 24V GND TXD RXD 1 2 3 4 F.01U.217.818 | 1.0 | 2011.04 Transformer BNC to Dome In/Out From Arm Harness C+ C- 5 6 7 8 In/Out ST Connector (Fiber) Power In Data In/Out Installation Manual Bosch Security Systems, Inc.
AutoDome 100 Series Fixed Camera 3.4.4 Installing Roof Parapet and Pipe Mounts | en 41 Power Supply Box Connections The following figure is a detailed illustration of the Roof or Pipe Mount Power Supply Box, 123 XF102 CONTROL IN/OUT P106 GND T XD RXD C+ C- 6 5 4 3 2 1 1 2 3 4 CONTROL TO DOM ME P105 GND T XD RXD C+ J103 J103 (LED) 24V NC 24V (FUSE)) DOME HTR P107 XF101 (FUSE)) P101 (FUSE)) J101 1 J102 5 4 3 2 1 XF103 which includes the fuse specifications.
en | Installing Roof Parapet and Pipe Mounts AutoDome 100 Series Fixed Camera The following table lists the Power Supply Box connectors: No.
AutoDome 100 Series Fixed Camera 2. Installing Roof Parapet and Pipe Mounts | en 43 Prepare the mounting surface for the type of fastener by drilling holes for the mounting anchors as required. Figure 3.6 Parapet Wall Mount Bracket and Roof Mount Plate 1 2 3 Pipearm 4 Parapet Wall Bracket 5 3/8-16 SS Hex Head Bolt (supplied) 6 Apply sealant around each fastener hole Roof Mount Plate Use a minimum of six (6) fasteners (not supplied). Eight (8) fastener holes shown.
en | Installing Roof Parapet and Pipe Mounts 6. AutoDome 100 Series Fixed Camera Remove the End Cap from the front of the arm and feed the video, control, and power wires up through the bottom of the pipe arm and out the front end. Figure 3.7 1 2 3 4 5 7. VG4-A-9230 Parapet Mount End Cap with O-ring Parapet Pipe Arm 1/4-20 SS Cap Screw Down Pipe 10-24 SS Pan Head Screw Fold the video, control, and power wires back at the front end of the arm and route them down and out through the Down Pipe.
AutoDome 100 Series Fixed Camera Installing Roof Parapet and Pipe Mounts | en 45 11. Run a bead of RTV Silicon sealant around the down pipe/Dome Cap interface to seal any gaps between the down pipe and the Dome Cap. 12. Proceed to Section 3.7 Wire the Pipe Interface Board, page 46. NOTICE! Use a guy-wire to aid in stabilizing the Parapet Arm. Replace the 1/4 inch cap screw with a threaded 1/4-inch stainless steel eye bolt (not supplied).
en | Installing Roof Parapet and Pipe Mounts 6. 7. AutoDome 100 Series Fixed Camera Apply the supplied thread sealant to the threads on the Pipe. – Make sure all surfaces are clean and dry. – Apply a bead of sealant completely around the leading threads of the male fitting. – Force the adhesive into the threads to thoroughly fill all voids. Thread the Pipe Cap onto the down pipe and tighten securely to prevent leaks. Refer to Figure 3.9, Page 45.
AutoDome 100 Series Fixed Camera Installing Roof Parapet and Pipe Mounts | en 47 Ref.
en | Installing Roof Parapet and Pipe Mounts 3.7.2 AutoDome 100 Series Fixed Camera Connecting Wires to the Pipe Interface Board The Pipe Interface Board contains all of the connectors for control, data, image, and power wires. Follow the procedures below to make the proper connections. WARNING! Use a 24 VAC Class 2 power supply only. 1. Attach a BNC connector to the video coax cable and connect it to its mating connector J102 on the Pipe Interface Board. 2.
AutoDome 100 Series Fixed Camera 6. Installing Roof Parapet and Pipe Mounts | en 49 To connect supervised alarms and relays, attach the appropriate wires to their terminals on the P104 connector on the Pipe Interface Board (see Figure 3.11, above). In addition, refer to Section 6 Alarms and Relay Connections, page 69 for more details on wiring alarms and relays. Note: There is a slot located at the top of the Interface Board to tie the wires to the circuit board with a cable tie. 7.
3.8 en | Installing Roof Parapet and Pipe Mounts AutoDome 100 Series Fixed Camera Attach Pendant to Pipe and Tighten 1. Before attaching the Pendant, visually inspect the Pendant dome and the Interface Board connectors for any blocked pin holes and bent pins. 2. Tilt the Pendant enough to place its mounting hook on top of the its housing, over the recessed hinge pin of the Dome Cap. a b c Figure 3.
AutoDome 100 Series Fixed Camera 3. Installing Roof Parapet and Pipe Mounts | en 51 Drop the Pendant down slightly to engage the dome hook and hinge pin of the Dome Cap, allowing the dome to rotate around the hinge pin. 4. Rotate the dome housing down to a vertical position and gently push upward to engage the connector on top of the dome housing. CAUTION! If you feel any resistance when rotating the dome housing or when engaging the connector, stop immediately and start over. 5.
en | Installing the In-Ceiling Mount AutoDome 100 Series Fixed Camera 4 Installing the In-Ceiling Mount 4.1 Unpacking This equipment should be unpacked and handled with care. If an item appears to have been damaged in shipment, notify the shipper immediately. Verify that all the parts listed in the product's Parts List below are included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative. Refer to Section 1.
AutoDome 100 Series Fixed Camera 4.3 Installing the In-Ceiling Mount | en 53 Dimensions 176.8 DIA. 6.96 210.7 8.30 150.2 5.91 19.0 0.75 94.0 3.70 153.9 6.06 204.3 8.04 mm inches Figure 4.1 4.4 In-ceiling Dimensional Outline Prepare Drywall Ceiling for Installation 1. 2. Choose the desired location to mount the dome. Use the bracket Base Plate as a template cut a 7 in. hole with a tolerance of ±1/8 in. (177.8 mm ±2.2 mm) hole in the ceiling with a drywall utility saw or Jig Saw.
4.5 en | Installing the In-Ceiling Mount AutoDome 100 Series Fixed Camera Prepare Suspension Ceiling for Installation 1. Choose the desired location to mount the dome, and remove an adjacent ceiling tile. 2. Loosen the four (4) securing screws, located in the corners of the Bracket Assembly, enough to hold the suspension bars but still allowing adjustment during installation. 3. Place the Bracket Assembly over the ceiling tile, which is used to mount the In-Ceiling AutoDome.
AutoDome 100 Series Fixed Camera 5. Installing the In-Ceiling Mount | en 55 Tighten the four (4) securing screws to the Bracket Assembly. Figure 4.4 Tighten Bracket Securing Screw 6. Secure the Bracket Assembly to an overhead securing point with a safety wire. Figure 4.5 Secure Bracket Assembly 4.6 Wire the Interface Box The Interface Box can be wired through the top or side. Use the supplied rubber plug to seal the hole which will not be used to route wires.
en | Installing the In-Ceiling Mount 4.6.1 AutoDome 100 Series Fixed Camera Make the Connections After routing all video, control, power, and alarm wires: 1. Attach a 3/4-inch NPS (20-mm) conduit fitting to the hole in which you bring in the wires. Be sure to thread the inside nut to the conduit fitting. 2. Route the video, control, power, and alarm wires through the conduit fitting and into the Interface Box. 3.
AutoDome 100 Series Fixed Camera 8. Installing the In-Ceiling Mount | en 57 To connect supervised alarms and relays, attach the appropriate wires to their terminals on the P104 connector on the Pipe Interface Board. Refer to Section 6 Alarms and Relay Connections, page 69 for more details on wiring alarms. 9. Attach the lid to the Interface box: a. Align the slots on the lid with the two posts at the rear of the Interface box. b. Rotate the lid down. c.
en | Installing the In-Ceiling Mount AutoDome 100 Series Fixed Camera The following table summarizes the pin connectors and their function: No. Connector Pin 1 Pin 2 P103 Alarms In Alarm 3 Alarm 4 Alarm 5 Alarm 6 P102 Alarms Out Alarm 1 Alarm 2 Alarm 3 GND P104 Analog Relay Relay Relay Relay N.O. COM N.C.
AutoDome 100 Series Fixed Camera 3. Installing the In-Ceiling Mount | en 59 Tighten the two (2) Thumbscrews to secure the Interface Box to the housing. Figure 4.10 1 2 3 In-Ceiling Housing and Interface Box Interface Box Ball Stud In-ceiling Housing 4 5 6 Thumb Screw Tether Point Ceiling Clamp CAUTION! The In-ceiling dome is provided with tether points on each side of the housing.
4.8 en | Installing the In-Ceiling Mount AutoDome 100 Series Fixed Camera Secure Housing to Ceiling The In-ceiling Housing is secured to the ceiling by two (2) screw clamps. 1. Insert the In-ceiling Mount Assembly through the hole in the ceiling. 2. Tighten both clamps using a #2 Phillips screwdriver, to secure the housing to the ceiling. 41.7 MAX. 1.64 CEILING 12.7 MIN. 0.50 CEILING mm inches Figure 4.
AutoDome 100 Series Fixed Camera 5 Cable and Wire Standards | en 61 Cable and Wire Standards CAUTION! Installation should only be performed by qualified service personnel in accordance with the National Electrical Code or applicable local codes. CAUTION! All wires for installation applications must be routed through a grounded conduit. 5.1 Power 115/230 VAC Copper Wire 5.2 To comply with local codes. Wire Distance Guide for Pendant 24 V to AutoDome VA / Watts 14 AWG (2.5 mm) 16 AWG (1.
en | Cable and Wire Standards 5.3.2 AutoDome 100 Series Fixed Camera Using UTP to Transmit Video and Control Unshielded twisted pair (UTP) cable terminated with RJ45 male connectors are used to transmit composite video using pins 1(+) and 2(-). Typically, a Coax to UTP cable converter is required at the head-end of the system. Bilinx control data can also be sent over the same two video wires (1 & 2).
AutoDome 100 Series Fixed Camera Cable and Wire Standards | en 5.4 Control-only Cables 5.4.1 Controlling the AutoDome via Biphase 63 (Shielded 2-wire, half-duplex, multi-drop, 5000 ft. cable limit) Biphase is the standard Bosch protocol used to send Pan/Tilt/Zoom control over 2-wire shielded twisted pair (STP) terminated with a 100 Ω terminal resistor. The AutoDome has a 100 Ω termination resistor between the Biphase C+ and C- terminals.
en | Cable and Wire Standards AutoDome 100 Series Fixed Camera In a daisy chain configuration, where multiple domes are connected in series, the 100 Ω resistor must be removed from all but the last dome. You can daisy chain a maximum of four (4) AutoDomes. 100 Ω Figure 5.3 1 2 3 4 5 6 7 8 5.4.
AutoDome 100 Series Fixed Camera Figure 5.4 1 2 3 4 5 6 65 Connections for RS232 Operation C- (Biphase) C+ (Biphase) Earth Ground RxD TxD Signal Ground Figure 5.5 1 2 3 4 Cable and Wire Standards | en 7 8 9 10 11 12 AutoDome Data In/Out P105/P106 Connector Head End RS232 TxD RxD Ground Position of CPU Switch for RS232 Operation (camera module not shown for clarity) Switch Location LEDs RS232 CPU Module Note: To access the CPU switch you must remove the bubble from the pendant housing.
en | Cable and Wire Standards AutoDome 100 Series Fixed Camera CAUTION! Bosch recommends that multiple RS485 connections be arranged as a connected series of point-to-point (multi-dropped) nodes, as a line or as a bus. It is not recommended to arrange RS485 connections as a star, ring, or as a multiple-connected network. Star and ring topologies may cause signal reflections or excessively low or high termination impedance.
AutoDome 100 Series Fixed Camera 5.5 Cable and Wire Standards | en 67 Fiber Optic Module with an RS232/RS422 Controller An AutoDome with a fiber optic module is prewired to operate with Biphase signals only. This section describes the procedures necessary to control a VG5 series AutoDome fitted with a fiber optic kit using an RS232 controller or a Pelco® RS422 controller.
en | Cable and Wire Standards AutoDome 100 Series Fixed Camera 10. Ensure that the VG5 AutoDome is set to receive RS232 commands. – Remove the bubble from the VG5 AutoDome housing. – Locate the protocol switch on the CPU board. – Ensure that the protocol switch is in the left position for RS232 operation. Figure 5.9 1 2 3 4 Position of CPU Switch for RS232 Operation Switch Location LEDs Move Switch to the left for RS232 Operation CPU Module 11. Return the bubble to the AutoDome housing. 12.
AutoDome 100 Series Fixed Camera Alarms and Relay Connections | en 6 Alarms and Relay Connections 6.1 Alarm Inputs 69 The AutoDome provides seven alarm inputs. Each input can be activated by dry contact devices such as pressure pads, passive infrared detectors, door contacts, and similar devices. The table below summarizes the size and distance wires. Wire Size Maximum Distance AWG mm feet meters 22 0.644 500 152.4 18 1.024 800 243.8 Table 6.
en | Alarms and Relay Connections 3. AutoDome 100 Series Fixed Camera From the AutoDome main menu, select Alarms Setup>Inputs Setup, and set the Alarm Input # to N.O.S. See the table below for contact and condition details. AutoDome Programmed N.O.S. 6.2.2 Contact Alarm Condition Open Normal Closed Alarm Cut or brake Tamper Configuring a Normally Closed Supervised Alarm 1. 2. Install a 2.2 K end-of-line resistor in the alarm circuit.
AutoDome 100 Series Fixed Camera 6.3.1 Alarms and Relay Connections | en 71 Configuring a Normally Open Non-supervised Alarm 1. Connect the alarm to the appropriate input (1 through 7) and ground at the AutoDome. Figure 6.3 N.O. - Normally Open Non-supervised Connections 1 2 2. Dry Contact Alarm Inputs 1 to 7 3 4 Dome Connector Ground From the AutoDome main menu select Alarm Setup>Inputs Setup, and set Alarm Input # to N.O. See the table below for contact and condition details.
en | Alarms and Relay Connections 6.4 AutoDome 100 Series Fixed Camera Alarm Outputs The AutoDome incorporates two (2) types of alarm outputs: a dry contact relay and three (3) open collector outputs or transistor outputs. 6.4.1 Configuring a Dry Contact Relay The dry contact relay acts like an on/off switch. It has a maximum voltage rating of 2 A @ 30 DC. 1. 2. Connect the appropriate stripped wire to the AutoDome COM connector. Connect the appropriate stripped wire to the N.O. or N.C.
AutoDome 100 Series Fixed Camera 7 Bubble Handling and Cleaning | en 73 Bubble Handling and Cleaning The bubble is made of Acrylic or Polycarbonate, depending on the application. Polycarbonate bubbles provide high impact resistance, and it’s optical clarity is comparable to glass or acrylic, although it’s surface is much softer. All bubbles require special care when handling and cleaning to avoid scratches. 7.1 Handling The bubble is packaged with a protective plastic sheet.
en | Bubble Handling and Cleaning AutoDome 100 Series Fixed Camera To remove the bubble from an in-ceiling housing 1. Loosen the lockscrew (item 1 in the illustration below) in the trim ring using a P1 or smaller Phillips screwdriver until the bubble can rotate freely. 2. Then rotate the bubble counterclockwise approximately 1/4 turn until it releases from the In-Ceiling Housing. See the figure below for an illustration. Figure 7.2 7.2.
en | Index AutoDome 100 Series Fixed Camera Index A F alarm connectors 18 alarm inputs 69 dry contact relay 72 non-supervised 70 normally closed non-supervised 71 normally closed supervised 70 normally open non-supervised 71 normally open supervised 69 supervised 69 with in-ceiling mount 56 with parapet roof or pipe mounts 48 with pendant arm, corner or mast mount 18, 25, 30 alarm outputs 72 open collector output 72 with in-ceiling mount 56 with parapet roof or pipe mount 48 with pendant arm, corner
AutoDome 100 Series Fixed Camera Index | en P T parapet arm stabilizing 45 pendant connector harness 26, 30 pendant arm attaching to power supply box 23 pendant arm, corner or mast mount mast plate 16 pendant assembly attaching to pipe mount 50 pendant bubble removing 73 pipe interface board 46, 49 pipe mount 33, 45 power supply box location 34 pole installation 16, 26 power supply fuse specifications 19 with fiber optic model 51 power supply box 37 attaching to pendant arm 23 connections for pendant ar
en | Index F.01U.217.818 | 1.0 | 2011.04 AutoDome 100 Series Fixed Camera Installation Manual Bosch Security Systems, Inc.
Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, PA 17601 U.S.A. www.boschsecurity.com © Bosch Security Systems, Inc.
