NEI-30 | VEI-30 Dinion Infrared Imager NEI | VEI Series en Quick Install Guide
NEI-30 | VEI-30 Dinion Infrared Imager Table of Contents | en 3 Table of Contents 1 Planning 4 1.1 Hardware Requirements 4 1.2 Pre-installation Checklist 5 2 Installation 6 2.1 Mount the Junction Box 6 2.2 Route Wires and Attach Connectors 7 2.3 Attach Pendant Arm to Junction Box 8 3 Connection 9 3.1 Power Connection 9 3.2 Video and Control Cables 3.3 Ethernet Connection (IP models) 10 3.4 Alarm Output Connections 10 4 Configuration 11 4.
1 en | Planning NEI-30 | VEI-30 Dinion Infrared Imager Planning CAUTION! CLASS 1 LED PRODUCT IEC60825-1 Ed. 1.2 (2001) WARNING! IMPORTANT MOUNTING INSTRUCTIONS This apparatus must be securely attached to the wall in accordance with these installation instructions. Failure to follow installation instructions may result in injury or death. CAUTION! Ensure that the selected location is protected from falling objects, accidental contact with moving objects, and unintentional interference from personnel.
NEI-30 | VEI-30 Dinion Infrared Imager 1.2 Planning | en 5 Pre-installation Checklist WARNING! This installation must be made by a qualified service person and must conform to all local codes. WARNING! CSA Certified / UL Listed CLASS 2 power adaptors or Certified PoE+ rated 42.5 VDC to 57 VDC, 600 mA, 34.20 W (max) power adaptor must be used in order to comply with electrical safety standards. 1. Determine the location and distance for the junction box based on its voltage and current consumption.
2 en | Installation NEI-30 | VEI-30 Dinion Infrared Imager Installation This chapter details how to mount the VEI-30 / NEI-30 to a wall. Any variations to the installation procedures are noted. 2.1 Mount the Junction Box Before mounting the junction box, decide if you should wire the box through the holes in the bottom or back of the box. If wiring the box through the back, move the two (2) seal plugs to the bottom through-holes before mounting.
NEI-30 | VEI-30 Dinion Infrared Imager Installation | en 1. Locate a stud in the wall and mark the outside edges of the stud. 2. Using the wall mount bracket as a template, align the mounting hole with the center of 7 the stud. 3. Mark the point on the wall in the center of the hole where the mounting bolt will be positioned. 4. Remove the wall mount bracket and drill a pilot hole at the marked point. 5. Align the wall mount bracket mounting hole with the hole drilled in the wall. 6.
2.3 en | Installation NEI-30 | VEI-30 Dinion Infrared Imager Attach Pendant Arm to Junction Box The bottom hinge pin of the Camera Arm is provided with a Hinge Pin Stop to hold the hinge open while attaching the arm to the junction box. 1. Compress the bottom hinge pin by pushing the pin lever downward and rotating it behind the Hinge Pin Stop. Figure 2.2 2. Camera Box Hinge Alignment Open the top hinge by pushing its pin lever up and holding it.
NEI-30 | VEI-30 Dinion Infrared Imager Connection | en 3 Connection 3.1 Power Connection 9 Connect power from a 12 VDC or 24 VAC class 2 power supply as follows: – Use AWG 16 to 22 stranded wire or AWG 16 to 26 solid wire; cut back 5 mm (0.2 in.) of insulation. – Loosen the screws of the supplied 2-pole connector and insert the wires. – Tighten the screws and insert the 2-pole connector into the power socket of the camera.
3.3 en | Connection NEI-30 | VEI-30 Dinion Infrared Imager Ethernet Connection (IP models) The NEI-30 connects to a 10 Base-T/100 Base-TX network either directly or via a hub. Both video and control are transmitted over a standard TCP/IP network using the built-in web server. In addition, power can be supplied to IP camera models via the Ethernet cable compliant with the Power-over-Ethernet Plus (IEEE 802.3at PoE+) standard.
NEI-30 | VEI-30 Dinion Infrared Imager 4 Configuration | en 11 Configuration All VEI-30 camera settings (except lens focus, focal length, and LED tilt) can be adjusted remotely using the Configuration Tool for Imaging Devices (CTFID) software application. Refer to the Configuration Tool for Imaging Devices User Manual located on the Bosch Security Systems website (www.boschsecurity.com).
en | Configuration NEI-30 | VEI-30 Dinion Infrared Imager Figure 4.2 1 2 3 4 4.2 Camera and LED Focal length adjustment Focus adjustment (zoom) Advanced camera setup controls - keypad LED tilt control Adjusting the Focus and Focal Length 1. 2. Use the top set screw (item 1, Figure 4.2) to adjust the image focus: – Turn the set screw to the left to focus toward (N) (near) (zoom in). – Turn the set screw to the right to focus toward (F) (far) (zoom out).
NEI-30 | VEI-30 Dinion Infrared Imager 4.3 Configuration | en 13 Making Pan Adjustments 1. Using the 4 mm hex key, loosen the bolts at the base of the “u bracket” to make the necessary pan adjustments. 4.4 2. When loosened, adjust the camera to the desired pan angle. 3. Tighten the bolt to secure in place. Making Tilt Adjustments 1. Unscrew the round caps (CCW) where the bracket attaches to the camera housing to expose the bolts for tilt adjustment. 2.
en | Configuration NEI-30 | VEI-30 Dinion Infrared Imager 4.5 Adjusting the Variable Field Illumination 4.5.1 Adjusting the LED Tilt Angle You can orient the LED array tilted either up or down to maximize infrared coverage over the field of view. On the rear of the camera housing is graphic for the LED tilt. Figure 4.6 LED tilt scale The “+” symbol indicates adjusting the LED tilt angle above the camera axis; and the “-” symbol indicates adjusting the LED tilt angle below the camera axis.
NEI-30 | VEI-30 Dinion Infrared Imager Configuration | en 15 To remove the 3D diffuser: 1. Remove the 3D diffuser and plate assembly as when installing the 3D diffuser. 2. Remove the 3D diffuser from the diffuser plate. 3. Install the diffuser plate into the camera housing to secure and seal the unit. Bosch Security Systems, Inc. Quick Install Guide F.01U.166.250 | 1.0 | 2011.
en | Index NEI-30 | VEI-30 Dinion Infrared Imager Index A accessing controls 11 adjusting LED tilt angle 14 attaching pendant arm 8 B Bilinx 9 BNC connector with pendant arm, corner or mast mount 7 C cable compensation 9 CAT-5E 10 CAT-6 10 coaxial cable 9 configuration 11 control data I/O plug 7 E ethernet 10 F fiber optic with pendant arm, corner or mast mount 7 H hardware requirements 4 I IEE 802.
NEI-30 | VEI-30 Dinion Infrared Imager Bosch Security Systems, Inc. Index | en Quick Install Guide 17 F.01U.166.250 | 1.0 | 2011.
en | Index F.01U.166.250 | 1.0 | 2011.04 NEI-30 | VEI-30 Dinion Infrared Imager Quick Install Guide Bosch Security Systems, Inc.
Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, PA 17601 U.S.A. www.boschsecurity.com © Bosch Security Systems, Inc.
