Installation manual

ManualsBrandsBosch ManualsPower ToolSolution 64

Intrusion Control Panel

Solution 64

Release Notes March, 2007

Security Systems

In the interest of ongoing product development and improvement, Bosch is proud to release software version 1 .50 for the

Solution 64 Security Control Panel. This document brieﬂy outlines the new features and improvements added in this release.

Please read in conjunction with the current installation manual and other addendums for more detailed information.

To coincide with this release, we are pleased to also announce that Version 1.07 of our Solution Link Upload/Download software

is now available. Version 1.07 includes increased functionality, as well as support for the additional features in the V1.50

Solution 64 release.

Release Notes for Version 1.50.00

NEW

Users Increased to 128.

Version 1.50 includes support for up to 128 users. Each user can

have a unique PIN number, Token and RF Keyfob if required.

Version 1.50 is supplied in all panels produced after March 2007.

It is not possible to upgrade panels manufactured earlier than

this date to 128 user capacity due to hardware diﬀerences.

The manufacture date can be found on the product

identiﬁcation sticker located on the main PCB.

NEW

Multi - Tenant Mode Added.

Version 1.50 includes additional support for multi-tennant

applications such as self storage garages or school storage

lockers etc.

When enabled, the new option Multi Tenant Mode option in

MENU 7-7-4 will lock the ﬁrst 48 users on the system to the ﬁrst

48 zones on the system. Each time the user enters their PIN the

corresponding zone is automtically bypassed allowing them to

access the zone (area).

Users 49 to 128 continue to operate as normal users.

System > Installer Options >

Installer Options



MENU 1-6-3

1 Report / Log Entry / Exit Installer Menu N

2 Report / Log Program Data Changed Y

3 Arm Only Installer PIN N

4 Zero Exit Time N

5 Auto Exit Installer Menu In 2 Hours Y

6 Auto Exit Service Mode In 2 Hours Y

7 Multi-tennant Mode N

8 Factory Defaulting Allowed Y

Note

A number of additional options and features in the

V1.50 release were originally released in V1.10.

To ﬁnd out more, please take the time to also

read the release notes for V1.10.



Support for up to 128 User PIN Codes



Support for up to 128 Token Users



Support for up to 128 RF Keyfob Users



Support for Multi-Tenant Applications

Summary of content (20 pages)

PAGE 1
Solution 64 Intrusion Control Panel Release Notes March, 2007 Release Notes for Version 1.50.00 In the interest of ongoing product development and improvement, Bosch is proud to release software version 1 .50 for the Solution 64 Security Control Panel. This document brieﬂy outlines the new features and improvements added in this release. Please read in conjunction with the current installation manual and other addendums for more detailed information.
PAGE 2
Solution 64 i Note The following options are included in this release however their functionality has been disabled as they are for future use. Please ignore the following options in this release. MENU 5-5 , MY Alarm MENU 5-0-3 , Check Web Email MENU 5-0-4 , Email System Log MENU 5-0-8 , Register Customer MENU 5-0-9 , Register Installer MENU 5-3-8 , User RAS PIN 2 © 2007 Bosch security Systems www.boschsecuritysystems.com BLCC110 N1.50 Issue: FTR1.
PAGE 3
Solution 64 Intrusion Control Panel Release Notes March, 2007 Release Notes for Version 1.10.00 In the interest of ongoing product development and improvement, Bosch is proud to release software version 1 .10 for the Solution 64 Security Control Panel. This document brieﬂy outlines the new features and improvements added in this release. Please read in conjunction with the current installation manual and other addendums for more detailed information.
PAGE 4
Solution 64 For example if 2 x CM110 Output Expanders are ﬁtted then Outputs 1 - 4 will be located on the main panel, Outputs 5 - 8 will be located on CM110 Expander 1 and Outputs 9 - 12 will be located on CM110 Expander 2. OUTPUT AND PROX READER MAPPING Device Type O utput Number Reader Numbe r Solution 64 Panel 1 -4 N/A CM110 Expander 1 5-8 9 -10 CM110 Expander 2 9 - 12 11 - 12 CM110 Expander 3 13 - 16 13 - 14 Proximity Readers 1 - 8 are reserved for Keypad Readers.
PAGE 5
Solution 64 Unlike other systems, no additional hardware or modules are required for DTMF control. To conﬁgure the desired functions see MENU 5-3-5 DTMF Options. See below for DTMF control operating instructions. 1. Once the panel answers the incoming call, if either option 1, 2, 3 or 4 in MENU 5-3-5 is enabled, then the panel will play a short welcome jingle. You now have approximately 5 seconds to enter a valid PIN and log onto the panel. 2. Enter PIN followed by the # key.
PAGE 6
Solution 64 In earlier versions, a Telco Alarm Fail would generate the alarm as programmed however no alarm memory would be displayed on the keypad once the sirens timed out. In this release, the system will display alarm memory for Telco Line Fail alarms. 15) Bypass Reports For Non Burglary Zone Types.
PAGE 7
Solution 64 25) Output Polarity “One Shot + Retrigger Corrected. In earlier versions, outputs programmed with a polarity type of “One Shot + Retrigger” did not operate correctly. The output failed to reset the one shot timer when the event retriggered which meant that output would operate at the speciﬁed one shot time rather than being reset for each retrigger. This has been corrected in V1.10 so that each retrigger causes the one shot timer to reset. 26) NEW Zone Trigger Delay Option Added. Version 1.
PAGE 8
Solution 64 32) NEW User RAS Security PIN Option Added. A new option has been added in this release to allow for an independant User connection to the panel using our Solution Link End User programming software. MENU 5-3-8, User RAS PIN option is defaulted to 00000000 and is currently reserved for future use. In Version 1.10 the default event assigment for all outputs has been changed to 0.
PAGE 9
Intrusion Control Panel Release Notes Solution 64 July, 2006 Release Notes for Version 1.05.01 In the interest of ongoing product development and improvement, Bosch is proud to release software version 1.05.01 for the Solution 64 Intrusion Control Panel. This document brieﬂy outlines the improvements added in this release. Please read in conjunction with the current installation manual and other addendums for more detailed information. 1) Zone Status Indicator (Green LED) Function Corrected.
PAGE 10
Solution 64 i Note The following options are included in this release however their functionality has been disabled as they are for future use. Please ignore the following options in this release. MENU 55 - MY Alarm MENU 503 - Check Web Email MENU 504 - Email System Log MENU 508 -Register Customer MENU 509 -Register Installer 2 © 2006 Bosch Security Systems www.boschsecuritysystems.com BLCC110N1.05.01 Issue: FTR1.
PAGE 11
Intrusion Control Panel Solution 64 Release Notes April, 2006 Release Notes for Version 1.05 In the interest of ongoing product development and improvement, Bosch is proud to release software version 1.05 for the Solution 64 Intrusion Control Panel. This document brieﬂy outlines the numerous new features and improvements added in this release. Please read in conjunction with the current installation manual and other addendums for more detailed information.
PAGE 12
Solution 64 7) NEW Arming In Part Mode Via Prox Readers. In previous versions it was not possible to conﬁgure a reader to only allow arming in Part mode as the reader still required the “Arming Allowed” option to be enabled. In this release the arm in part mode via prox reader feature has been improved and it is now possible to conﬁgure a reader to only allow arming and disarming from part mode.
PAGE 13
Intrusion Control Panel Solution 64 Release Notes February, 2006 Release Notes for Version 1.04.04 In the interest of ongoing product development and improvement, Bosch is proud to release software version 1.04.04 for the Solution 64 Intrusion Control Panel. This document briefly outlines the numerous new features and improvements added in this release. Please read in conjunction with the current installation manual and other addendums for more detailed information.
PAGE 14
Solution 64 8) NEW Restrict Installer Access Per Keypad Option Added. In installations with multiple keypads, you may want to restrict the installer code access to one or a limited number of keypads. For example you may want to restrict installer access to only the keypad which is located in the communication room. To configure this option, select “Installer PIN Not Allowed” option for each required Keypad. See MENU 6-1-5, Option 7 below. 9) NEW Prevent PIN Arm/Disarm Per Keypad Option Added.
PAGE 15
Solution 64 Should the trouble event still be in effect at 7am the keypad beeper will start to sound. At all times the trouble event will be displayed on the keypad and stored into the system log. d) MENU 7-7-1 Reset Siren All Users This option has been defaulted to YES because in most cases in a partitioned system you would want all authorised users to be able to reset the sirens. System > System Options > Area Options  MENU 7-7-1 This has been corrected in the 1.04.
PAGE 16
Solution 64 19) Turn Area On / Off Command Corrected In previous versions, the Turn Area On / Off option (MENU 2-0-1) does not filter the user to restrict them from controlling an area they don’t belong to. 23) NEW Tone Bypass Function Implemented It is often difficult to establish a remote connection to a panel if the customer picks up the phone or if a fax or answering machine answers the call before the panel does. In version 1.04.
PAGE 17
Intrusion Control Panel Solution 64 Release Notes December, 2005 Release Notes for Version 1.04 In the interest of ongoing product development and improvement, Bosch is proud to release version 1.04 of the Solution 64 Intrusion Control Panel. This document briefly outlines the numerous new features and improvements added in this release. Please read in conjunction with the current installation literature for more detailed information.
PAGE 18
Solution 64 9) NEW Auto Arm Time Extended Report If the user extends the auto arm time, the panel will report a CID event 464 to the monitoring station. 10) NEW EOL Resistor Value Changes The following EOL resistor values have been added making it easier to change over of Tecom and Concept panels. 16) Direct Link Request Command Start Direct Link To allow for these two options we have removed support for 12K and 15K EOL resistor values.
PAGE 19
Solution 64 1) 20) NEW Key-Switch Open Close Option Added Version 1.04 includes a new feature which allows you to select whether or not a zone programmed as a Key-switch Zone, will send opening and closing reports. The default is set to Off. A001 Security System A002 Area 2 Name A003 Area 3 Name Press  OK or MENU Inputs > Global Input Options > Input Options  To set the required chime mode enter [MENU] + [2] + [0] + [6] and select the area from the list then press [OK].
PAGE 20
Solution 64 29) NEW Arming in Part Mode In earlier versions, zones marked as Do Not Test On Exit were still being checked when the system was armed in Part Mode. In version 1.04 zones marked as “Do Not Test On Exit” are no longer checked when arming in Part Mode. 30) NEW Display Alarms In Scroll List While Armed This new option will cause the scroll list to display all alarm events that are currently in effect while the system is armed.