3FHJTUFS ZPVS OFX #PTDI OPX XXX CPTDI IPNF DPN XFMDPNF %JTIXBTIFS FO 0QFSBUJOH JOTUSVDUJPOT SM… SB…
K % $ K K PLQ 6WDUW & 5HVHW VHF 5HVHW VHF
en Table of contents 8 Intended use . . . . . . . . . . . . . . . ( Safety instructions . . . . . . . . . . Before you switch ON the appliance . . . . . . . Delivery. . . . . . . . . . . . Installation. . . . . . . . . . In daily use . . . . . . . . . Door lock . . . . . . . . . . Button lock . . . . . . . . . Damage . . . . . . . . . . . Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
en Intended use Automatic switch off / interior light . Switching off the appliance. . . . . . . Interrupting the programme . . . . . . Terminating the programme . . . . . . Changing the programme. . . . . . . . Intensive drying. . . . . . . . . . . . . . . . . 24 . 24 . 25 . 25 . 25 . 25 2 Cleaning and maintenance . . . Overall condition of the machine Special salt and rinse aid . . . . . . Filters . . . . . . . . . . . . . . . . . . . . . Spray arms . . . . . . . . . . . . . . . . .
Safety instructions Delivery 1. Check the packaging and dishwasher immediately for damage caused in transit. Do not switch on a damaged appliance, but contact your supplier. 2. Please dispose of the packaging material in an environmentally friendly manner. 3. Do not let children play with packaging and its parts. There is a risk of suffocation from collapsible boxes and film.
en Safety instructions If you cannot obtain any information from the manufacturer, you must not install the dishwasher above or below these appliances. If you install a microwave oven above the dishwasher, the microwave oven may be damaged. Install built-under or integratable appliances only under continuous worktops which have been screwed to adjacent cupboards to ensure stability.
Safety instructions en Deactivating the button lock: Disposal Hold down the button + for approx. 4 sec. until the display ’– goes out. When the programme ends (‹:‹‹ on the digital display), the button lock is cancelled. If there is a power failure, the button lock is retained. Whenever a programme is restarted, the button lock must be reactivated. 1. Make redundant appliances unusable to prevent subsequent accidents. 2. Dispose of the appliance in a n environmentally friendly manner.
en Safety instructions m Warning Risk of explosion! Do not add any solvents to the washing chamber. Danger of explosion! m Warning Risk of scalding! Open the door carefully when the programme is still running. There is a risk of hot water spraying out of the appliance. m Warning Risks to children! If fitted, use the childproof lock. An exact description can be found in the back of the enve lope. Do not allow children to play with or operate the appliance.
Protection of the environment 7 Protection of the * Getting to know your environment onitceotPr het of Both the packaging of new appliances and the old appliances themselves contain valuable raw materials and recyclable materials. Please dispose of the individual parts separated according to type. Please ask your dealer or inquire at your local authority about current means of disposal. Packaging All plastic parts of the appliance are identified with internationally standardised abbreviations (e.g.
Water softening system/Special salt en Appliance interior 1" Interior light * 1* Cutlery drawer 12 Top basket 1: Top spray arm 1B Tablet collecting tray 1J Intake opening 1R Blow opening (Zeolith container) 1Z Bottom spray arm 1b Dispenser for special salt 1j Filters 9" Bottom basket 9* Dispenser for rinse aid 92 Detergent dispenser 9: Lock for detergent dispenser 9B Rating plate * depending on model Overview of menu The settings can be found in the individual chapters.
Water softening system/Special salt To change the setting: 1. Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of •:‹ˆ has been reached, the display jumps back to •:‹‹ (off). 2. Press START button h. The chosen setting has now been stored.
en Rinse aid Using detergents with salt component Det rgentswithsaltcompone t If combined detergents with a salt component are used, salt can usually be omitted up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/ l). If the water hardness is over 21° dH, special salt must be used. Switching off salt refill indicator/water softening system Switchingof watersofteni gsy tem If the salt refill indicator @ is impaired (e.g.
Rinse aid 2. Carefully pour rinse aid up to the max. mark in the filler opening. PD[ 3. Close cover until it clicks shut. 4. To prevent excessive foam formation during the next rinse cycle, remove any rinse aid which has run over with a cloth. Setting amount of rinse aid The amount of rinse aid can be set from §:‹‹ to §:‹‡. Please set rinse aid on §:‹† to obtain very good drying results (§:‹† is already set in factory).
en Utensils - Utensils slinseUt Not suitable Cutlery and utensils made of wood. Delicate decorative glasses, craft and antique utensils. These decors are not dishwasher-proof. Plastic parts not resistant to heat. Copper and tin utensils. Utensils which are soiled with ash, wax, lubricating grease or ink. Aluminium and silver parts have a tendency to discolour and fade during the wash cycle. Even some types of glass (e.g. crystal glass objects) may turn cloudy after many wash cycles.
Utensils Cups and glasses Top basket 12 en Tip Heavily soiled utensils (pans) should be placed in the bottom basket. The more powerful spray jet provides a better dishwashing result. Tip Other examples, such as the best way of loading your dishwasher, can be found on our homepage as a free download. The corresponding Internet address can be found on the back page of these instructions for use. Cutlery drawer Arrange the cutlery in the cutlery drawer 1* as illustrated.
en Utensils Small accessories holder * Smal ac es oriesholder * depending on model Light-weight plastic accessories, e.g. cups, lids, etc. can be held securely in the small accessories holder. &/,&. Adjusting the height of the basket Foldingspikes The height of the upper utensils basket 12 can be adjusted in 3 stages to create more space either in the upper or lower basket. Folding spikes * * depending on model The spikes can be folded down to improve arrangement of pans, bowls and glasses.
Detergent 1. Pull out the top basket 12 out. 2. To lower the basket, press in the left and then the right lever on the outside of the basket. In doing so, hold the sides of the basket along the upper edge to prevent it from suddenly dropping. 3. To raise the basket, hold the basket on the sides of the upper edge and lift it up. 4. Before re-inserting the basket again, ensure that it is at the same height on both sides.
en Detergent Adding detergent 1. If the detergent dispenser 92 is still closed, press the lock 9: to open the detergent dispenser. Pour detergent into the dry detergent dispenser 92 only (insert tablet flat, not on its edge). Dosage: see manufacturer’s instructions on the packaging. The graduated detergent dispenser 92 helps you add the correct amount of powder or liquid detergent. Usually 20 ml–25 ml are adequate for normal soiling. If using tablets, one tablet is adequate. PO PO PO 2.
Detergent Combination detergent Apart from conventional detergents (Solo), a number of products are offered with additional functions. These products contain not only the detergent but also rinse-aid and salt replacement substances (3in1) and, depending on the combination (4in1, 5in1, etc.), additional components such as glass protection or stainless steel cleaner. Combination detergents function only up to a specific degree of hardness (usually 21°dH). Over this limit salt and rinse-aid must be added.
en Overview of programmes / Overview of programmes m aogrm prseofw eviO rve The max. possible number of programmes is illustrated in this overview. The corresponding programmes and their arrangement can be found on the fascia.
Additional options en § Half load * Programme selection Half oad You can select a suitable programme according to the type of utensils and degree of soiling. If you have only a few items to wash (e.g. glasses, cups, plates), you can switch to “half load”. This will save water, energy and time. It is recommended to put a little less detergent in the detergent dispenser than for a full load. Information for test institutes Test institutes receive the information for comparability tests (e.g.
en Operating the appliance Zeolith drying 1 Operating the appliance ngitaO rpe Programme data The programme data (consumption values) can be found in the summary of instructions. They refer to normal conditions and the water hardness set value •:‹…. Different influencing factors such as e.g. water temperature or line pressure may result in deviations.
Operating the appliance Switching on the appliance 1. Turn on the tap fully. 2. Switch on ON/OFF switch (. The Eco 50° programme display flashes. This programme remains selected if no other programme button 0 is pressed. The expected programme duration flashes on the digital display )*. 3. Press the START button h. The programme starts running. Note - for environmentally friendly operation of the dishwasher: For ecological reasons the Eco 50° programme is preset whenever the appliance starts.
en Operating the appliance Automatic switch off after end of programme or interior light* Automaticswitchof /interiorlight * depending on model To save energy, the dishwasher can be automatically switched off 1 min or 120 min after the programme ends. The setting can be selected from ˜:‹‹ to ˜:‹ƒ. ˜:‹‹ Appliance does not switch off automatically. The interior light 1" comes on when the door is opened irrespective of whether the ON/OFF switch ( is switched on or off.
Operating the appliance en Interrupting the programme Intensive drying 1. Switch off ON/OFF switch (. The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. 2. To continue the programme, switch on the ON/OFF switch ( again.
en Cleaning and maintenance 2 Cleaning and maintenance ngniaeCl nda A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Overall condition of the machine Check spray arm for grease and limescale deposits. If you find such deposits: Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature.
Cleaning and maintenance en Filters Spray arms The filters 1j keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters. The filter system consists of a coarse filter, a flat fine filter and a microfilter. 1. After each washing cycle check the filters for residue. 2. Unscrew filter cylinder as illustrated and take out filter system.
en Fault, what to do? 3 Fault, what to do? ,tF ula w tha ot Experience has shown that you can rectify most faults which occur in daily operation yourself. This ensures that the machine is quickly available to you again. In the following overview you can find possible causes of malfunctions and helpful information for rectifying them. Note If the appliance stops during dishwashing or does not start for no obvious reason, first run the Abort programme function (Reset).
Fault, what to do? en Fault table Fault “Check water supply” display 8 lights up. Cause Supply hose kinked. Tap turned off. Tap jammed or calcified. Remedial action Install supply hose without kinks. Turn on the tap. Turn on the tap. Flow rate must be min. 10 l/min. when water supply is open. Filter in the water supply blocked. Switch off the appliance and pull out the mains plug. Turn off the tap. Unscrew water connection. Error code “:ƒƒ is lit. Filters 1j are soiled or blocked.
en Fault, what to do? Fault A different error code is indicated on the digital display. (“:‹‚ to “:„‹) Cause A technical fault has probably occurred. Display flashes Door not closed properly. Refill indicator for salt @ No rinse aid. and/or rinse-aid H is lit. No salt. Sensor does not detect salt tablets. Refill indicator for salt @ Refill indicator switched off. and/or rinse-aid H is not lit. There is still enough special salt/ rinse aid available.
Fault, what to do? Fault Utensils not dry. Cause No or too little rinse aid in the dispenser. Programme selected without drying. Water collecting in depressions on the utensils and cutlery. en Remedial action Refill rinse aid. Select programme with drying (see Overview of programmes, Programme sequence). Arrange utensils in a sloping position, arrange affected utensils as sloping as possible. The combined detergent used has a poor drying performance.
en Fault, what to do? Fault Food remnants on the utensils. Cause Utensils placed too closely together, utensils basket overfilled. Spray arm rotation obstructed. Spray arm nozzles blocked. Filters 1j dirty. Filters 1j inserted incorrectly and/or not engaged. Rinse programme too weak. Utensils precleaned too intensely; sensors therefore decide on weak programme sequence. Stubborn soiling cannot be completely removed. Tall narrow receptacles in corner areas are not rinsed adequately.
Fault, what to do? Fault Water stains on plastic parts en Cause Droplet formation on plastic surface is physically unavoidable. After drying, water stains are visible. Remedial action Use a more intensive programme (more water changes). Arrange utensils in a sloping position. Use rinse aid. If required, increase softening setting. Washable or water-soluble Detergent substances are Change detergent brand. coatings in the container or deposited. These coatings cannot Clean appliance mechanically.
en Fault, what to do? Fault Coloured (blue, yellow, brown), difficult to remove to non-removable coatings in the appliance or on stainless steel utensils. Coloured (yellow, orange, brown), easily removable deposits inside the appliance (mainly in the floor area) Plastic parts discoloured. Removable streaks on glasses, glasses with metallic appearance and cutlery. Initial or existing, irreversible clouding of glass. 34 Cause Film formation consisting of ingredients from vegetables (e.g.
Fault, what to do? Fault Rust spots on the cutlery. The appliance does not start. Programme starts automatically. The door is difficult to open. Door cannot be closed. Cover on the detergent dispenser cannot be closed. Detergent residue in the detergent dispenser or in the tablet collecting tray. Cause Cutlery not adequately rustresistant. Knife blades are frequently more severely affected. Cutlery will also rust if rusting parts are rinsed at the same time (pan handles, damaged utensil baskets, etc.).
en Customer service Fault Appliance stops in the programme or programme is interrupted. Filling valves making striking noises. Knocking or rattling noise. Unusual foam formation. Cause Door not closed properly. Do not place utensils or fragrance dispenser in the tablet collecting tray. Top basket presses against inner door and prevents door from being closed securely. Power and/or water supply interrupted. Depends on domestic installation, as appliance is not defective. No effect on appliance function.
Installation and connection Delivery 5 Installation and connection onitallatnsI nda The dishwasher must be connected correctly, otherwise it will not function properly. The specifications for the inlet and outlet as well as the electrical connected loads must correspond with the required criteria as specified in the following paragraphs or in the installation instructions. Install the appliance in the correct sequence: 1. Checking appliance on delivery 2. Installing the appliance 3.
en Installation and connection Installation Drinking water connection The required installation dimensions can be found in the installation instructions. Level the appliance with the aid of the height-adjustable feet. Ensure that the appliance is situated securely on the floor. A built-under or integrated appliance which is installed subsequently as a free-standing appliance must be secured to prevent it from overturning, e.g.
Installation and connection Setting hot water: 1. Close the door. 2. Switch on ON/OFF switch (. 3. Hold down programme button # and press START button h until •:‹... is indicated on the digital display. 4. Release both buttons. The LED for button # flashes and the digital display )* displays the factory setting •:‹…. 5. Press programme button # until the factory set value ‘:‹‹ is indicated on the digital display )*. To change the setting: 1.
en Installation and connection Transportation Protection against frost Empty the dishwasher and secure loose parts. Drain the appliance according to the following steps: 1. Turn on the tap. 2. Close the door. 3. Switch on ON/OFF switch (. 4. Select programme with the highest temperature. The expected programme duration is indicated on the numerical display )*. 5. Press START button h. Programme sequence starts. 6. After approx.
&KLOGSURRI ORFN GRRU ORFN :DUQLQJ $FWLYDWH WKH FKLOGSURRI ORFN 2SHQ WKH GRRU ZLWK DFWLYDWHG FKLOGSURRI ORFN 'HDFWLYDWH FKLOGSURRI ORFN $OZD\V FORVH WKH DSSOLDQFH GRRU FRPSOHWHO\ ZKHQ \RX OHDYH WKH DSSOLDQFH 7KLV LV WKH RQO\ ZD\ \RX FDQ SURWHFW \RXU FKLOGUHQ IURP SRWHQWLDO GDQJHUV %DNLQJ VKHHW VSUD\ KHDG /DUJH VKHHWV RU JULOOHV DQG SODWHV ZKLFK KDYH D GLDPHWHU JUHDWHU WKDQ FP JRXUPHW SODWHV SDVWD SODWHV GLQQHU SODWHV FDQ EH FOHDQHG ZLWK WKH DLG RI WKH VSUD\ KHDG 7R G
$TXD6WRS JXDUDQWHH EPFT OPU BQQMZ UP BQQMJBODFT XJUIPVU "RVB4UPQ *O BEEJUJPO UP XBSSBOUZ DMBJNT BHBJOTU UIF TFMMFS CBTFE PO UIF QVSDIBTF DPOUSBDU BOE JO BEEJUJPO UP PVS BQQMJBODF XBSSBOUZ XF XJMM QBZ EBNBHFT VOEFS UIF GPMMPXJOH DPOEJUJPOT *G PVS "RVB4UPQ TZTUFN JT EFGFDUJWF BOE DBVTFT XBUFS EBNBHF XF XJMM NBLF HPPE UIF EBNBHF GPS QSJWBUF VTFST 5P FOTVSF XBUFS EBNBHF QSPUFDUJPO UIF BQQMJBODF NVTU CF DPOOFDUFE UP UIF QPXFS TVQQMZ 5IJT MJBCJMJUZ HVBSBOUFF JT WBMJE GPS UIF TFSWJDF MJGF PG UIF
