3FHJTUFS ZPVS OFX #PTDI OPX XXX CPTDI IPNF DPN XFMDPNF %JTIXBTIFS FO 0QFSBUJOH JOTUSVDUJPOT SM… SB…
K K K 6WDUW 5HVHW VHF 5HVHW VHF
en Table of contents 8 Intended use . . . . . . . . . . . . . . . ( Safety instructions . . . . . . . . . . Before you switch ON the appliance Delivery. . . . . . . . . . . . . . . . . . . . . . . Installation. . . . . . . . . . . . . . . . . . . . . In daily use . . . . . . . . . . . . . . . . . . . . Door lock . . . . . . . . . . . . . . . . . . . . . Damage . . . . . . . . . . . . . . . . . . . . . . Disposal . . . . . . . . . . . . . . . . . . . . . . 4 4 .4 .5 .5 .6 .6 .6 .
en Intended use 3 Fault, what to do? . . . . . . . . . . 24 Waste water pump . . . . . . . . . . . . . . 24 Fault table . . . . . . . . . . . . . . . . . . . . . 25 4 Customer service . . . . . . . . . . 5 Installation and connection . . Product package . . . . . . . Safety instructions. . . . . . . Delivery. . . . . . . . . . . . . . . Technical specifications . . Installation. . . . . . . . . . . . . Waste-water connection . . Drinking water connection Electrical connection. . . . .
Safety instructions Delivery 1. Check the packaging and dishwasher immediately for damage caused in transit. Do not switch on a damaged appliance, but contact your supplier. 2. Please dispose of the packaging material in an environmentally friendly manner. 3. Do not let children play with packaging and its parts. There is a risk of suffocation from collapsible boxes and film.
en Safety instructions If you cannot obtain any information from the manufacturer, you must not install the dishwasher above or below these appliances. If you install a microwave oven above the dishwasher, the microwave oven may be damaged. Install built-under or integratable appliances only under continuous worktops which have been screwed to adjacent cupboards to ensure stability.
Safety instructions m Warning Risk of injury! To prevent injuries, e.g. caused by stumbling, open the dishwasher only briefly in order to load and unload the dishwasher. Knives and other utensils with sharp points must be placed in the cutlery basket with the points downwards or horizontally on the knife shelf*. Do not lean or sit on the open door. In the case of free-standing appliances, ensure that the baskets are not overloaded.
en Protection of the environment When opening and closing the door on an eye-level appliance, ensure that children do not become jammed or crushed between the appliance door and the cupboard door below. Children could become locked in the appliance (danger of suffocation) or get into another dangerous situation. Redundant appliances: Pull out the mains plug, sever and dispose of the power cord. Destroy the door lock so that the door can no longer be closed.
Getting to know your appliance Appliance interior * Getting to know your appliance ngitG te knowot oury Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front. Individual positions are referred to in the text.
en Water softening system/Special salt Setting The amount of salt dispensed can be set in 4 stages depending on the hardness of your water. Accordingly 0, 1, 2 or 3 displays are lit (see table). Factory setting: 1. 1. Find out about the hardness value of your tap water. Your water utility company will help you with this. 2. Setting can be found in the water hardness table. 3. Close the door. 4. Switch on ON/OFF switch (. The Cleaning display )* flashes. 5. Press and hold down the START button @. 6.
Rinse aid As soon as the salt refill indicator ` on the fascia is lit, top up the salt. , Rinse aid ensRi * depending on model Using detergents with salt component Det rgentswithsaltcompone t dia As soon as the rinse-aid refill indicator X is lit on the fascia, there is still a rinse-aid reserve of 1-2 rinsing processes. Refill with rinse aid. The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid for domestic dishwashers.
en Utensils 3. Close cover until it clicks shut. 4. To prevent excessive foam formation during the next rinse cycle, remove any rinse aid which has run over with a cloth. Setting amount of rinse aid The amount of rinse aid dispensed can be set in 4 stages. Accordingly 0, 1, 2 or 3 displays are lit (see water hardness table). Factory setting: 2. Do not change the amount of rinse aid unless streaks (select lower setting) or water stains (select higher setting) are left on the utensils. 1. Close the door.
Utensils Recommendation: Use only glasses and porcelain which the manufacturer designates as dishwasher-proof. Use a detergent which protects utensils. Take glass and cutlery out of the dishwasher as soon as possible after the programme ends. en Cups and glasses Top basket 1" Loading the dishwasher 1. Remove large food remnants. It is not necessary to prerinse utensils under running water. 2. Place the utensils so that – they are secure and cannot tip over. – all utensils with their openings face down.
en Utensils Tip Other examples, such as the best way of loading your dishwasher, can be found on our homepage as a free download. The corresponding Internet address can be found on the back page of these instructions for use. * Depending on the model, a 3-fold height adjustment is possible. To do this, first place the etagere vertically and pull up, then place at a slight angle, push down to the required height (1, 2, or 3) and snap into place.
Utensils en Knife shelf * Top basket with side levers * depending on model Long knives and other utensils can be arranged horizontally. 1. Pull out the top basket 1" out. 2. To lower the basket, press in the left and then the right lever on the outside of the basket. In doing so, hold the sides of the basket along the upper edge to prevent it from suddenly dropping.
en Detergent . Detergent ntgereD te You can use tablets as well as powder or liquid detergents for dishwashers, but never use washing up liquid. The dosage can be individually adjusted with powder or a liquid detergent according to the degree of soiling. Tablets contain an adequately large amount of active ingredients for all cleaning tasks. Modern, powerful detergents predominantly use a lowalkaline formulation with phosphate and enzymes. Phosphates bond the lime in the water.
Detergent Tip If the utensils are only lightly soiled, slightly less than the indicated amount of detergent is usually adequate. Suitable detergents and care products can be purchased online via our website or via customer service (see back page). Combination detergent Apart from conventional detergents (Solo), a number of products are offered with additional functions.
en Overview of programmes / Overview of programmes m aogrm prseofw eviO rve The max. possible number of programmes is illustrated in this overview. The corresponding programmes and their arrangement can be found on the fascia.
Additional options en Ï Intensive zone * Intensivezone Programme selection Perfect for a mixed load. You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket. The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly. You can select a suitable programme according to the type of utensils and degree of soiling.
en Operating the appliance 1 Operating the appliance ngitaO rpe Programme data The programme data (consumption values) can be found in the summary of instructions. This data refers to normal conditions and the water hardness set value 2. Different influencing factors such as water temperature or mains pressure may result in deviations. encaiplahet Note - for environmentally friendly operation of the dishwasher: The Eco 50° programme is a particularly environmentally friendly programme.
Operating the appliance en Interrupting the programme Intensive drying 1. Switch off ON/OFF switch (. The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. 2. To continue the programme, switch on the ON/OFF switch ( again.
en Cleaning and maintenance 2 Cleaning and maintenance ngniaeCl nda A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Overall condition of the machine Check spray arm for grease and limescale deposits. If you find such deposits: Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature.
Cleaning and maintenance en Filters Spray arms The filters 1R keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters. The filter system consists of a coarse filter, a flat fine filter and a microfilter. 1. After each washing cycle check the filters for residue. 2. Unscrew filter cylinder as illustrated and take out filter system.
en Fault, what to do? 3 Fault, what to do? ,tF ula w tha ot Experience has shown that you can rectify most faults which occur in daily operation yourself. This ensures that the machine is quickly available to you again. In the following overview you can find possible causes of malfunctions and helpful information for rectifying them. Note If the appliance stops during dishwashing or does not start for no obvious reason, first run the Abort programme function (Reset).
Fault, what to do? en Fault table Fault “Check water supply” display h lights up. Cause Supply hose kinked. Tap turned off. Tap jammed or calcified. Remedial action Install supply hose without kinks. Turn on the tap. Turn on the tap. Flow rate must be min. 10 l/min. when water supply is open. Filter in the water supply blocked. Switch off the appliance and pull out the mains plug. Turn off the tap. Unscrew water connection. Filters 1R are soiled or blocked. Waste water hose is blocked or kinked.
en Fault, what to do? Fault Cause Refill indicator for salt ` No rinse aid. and/or rinse-aid X is lit. No salt. Sensor does not detect salt tablets. Refill indicator for salt ` Refill indicator switched off. and/or rinse-aid X is not lit. There is still enough special salt/ rinse aid available. Water is left Filter system or area under in the appliance at the end the filters 1R is blocked. of the programme. The programme has not yet ended. Utensils not dry. No or too little rinse aid in the dispenser.
Fault, what to do? Fault Cause Appliance interior wet after No appliance fault. rinse cycle. Food remnants on the utensils. Utensils placed too closely together, utensils basket overfilled. Spray arm rotation obstructed. Spray arm nozzles blocked. Filters 1R dirty. Filters 1R inserted incorrectly and/or not engaged. Rinse programme too weak. Utensils precleaned too intensely; sensors therefore decide on weak programme sequence. Stubborn soiling cannot be completely removed.
en Fault, what to do? Fault Detergent residue Water stains on plastic parts Cause Detergent dispenser cover blocked by utensils and therefore does not open fully. Detergent dispenser cover blocked by the tablet. Tablets used in the quick or short programme. Dissolving time of the detergent is not reached in the selected short programme. Washing effect and dissolving performance are reduced after a prolonged storage time or detergent is very lumpy.
Fault, what to do? Fault White, stubborn coatings; limescale on the utensils, container or door. Cause Detergent substances are deposited. These coatings cannot usually be removed with chemicals (appliance cleaner, ...). Hardness range incorrectly set or water hardness greater than 8.9 mmol/l. 3 in 1 detergent or bio/eco detergent not effective enough. Underdosing of detergent. Tea or lipstick residue on the utensils. Too weak rinse programme selected. Too low rinsing temperature.
en Fault, what to do? Fault Removable streaks on glasses, glasses with metallic appearance and cutlery. Initial or existing, irreversible clouding of glass. Rust spots on the cutlery. The appliance does not start. Programme starts automatically. 30 Cause Too much rinse aid. No rinse aid added or setting too low. Detergent residue in the final rinse programme section. Detergent dispenser cover blocked by utensils (cover does not open fully).
Fault, what to do? Fault Appliance cannot be set (hardness, final rinse, ...). The door is difficult to open. Door cannot be closed. Cover on the detergent dispenser cannot be closed. Detergent residue in the detergent dispenser or in the tablet collecting tray. Appliance stops in the programme or programme is interrupted. Filling valves making striking noises. Knocking or rattling noise. Unusual foam formation. Cause Appliance is in the programme.
Customer service en 4 Customer service om C treus 5 Installation and connection ecvires If you are unable to rectify the fault, please contact your customer service. We always find a suitable solution, even to avoid unnecessary visits by technicians. Contact information for your nearest customer service can be found on the back of these instructions for use or on the enclosed customer service list. When calling, please state the appliance number (ENr.
Installation and connection en Delivery Installation Your dishwasher has been checked thoroughly in the factory to ensure that it is in working order. This may cause small water stains. These will disappear after the first wash cycle. The required installation dimensions can be found in the installation instructions. Level the appliance with the aid of the height-adjustable feet. Ensure that the appliance is situated securely on the floor.
en Installation and connection Drinking water connection 1. Fasten the drinking water connection to the tap according to the installation instructions using the enclosed parts. Ensure that the drinking water connection is not kinked, crushed or twisted. 2. When replacing the appliance, always use a new water supply hose. Water pressure: At least 0.05 MPa (0.5 bar), maximum 1 MPa (10 bar). At a higher water pressure: connect pressure-reducing valve ahead.
Installation and connection en Removing the appliance Transportation Also observe the sequence of worksteps here. 1. Disconnect the appliance from the power supply. 2. Turn off the water supply. 3. Undo the waste water and drinking water connection. 4. Loosen fastening screws for the furniture parts. 5. If fitted, remove the base panel. 6. Pull out the appliance, carefully pulling the hose behind. Empty the dishwasher and secure loose parts. Drain the appliance according to the following steps: 1.
en Installation and connection Protection against frost Protectionag instfrost(Emptyingtheap liance) If the appliance is in a room where there is a risk of frost (e.g. holiday home), empty the appliance completely (see Transportation).
&KLOGSURRI ORFN GRRU ORFN :DUQLQJ $FWLYDWH WKH FKLOGSURRI ORFN 2SHQ WKH GRRU ZLWK DFWLYDWHG FKLOGSURRI ORFN 'HDFWLYDWH FKLOGSURRI ORFN $OZD\V FORVH WKH DSSOLDQFH GRRU FRPSOHWHO\ ZKHQ \RX OHDYH WKH DSSOLDQFH 7KLV LV WKH RQO\ ZD\ \RX FDQ SURWHFW \RXU FKLOGUHQ IURP SRWHQWLDO GDQJHUV %DNLQJ VKHHW VSUD\ KHDG /DUJH VKHHWV RU JULOOHV DQG SODWHV ZKLFK KDYH D GLDPHWHU JUHDWHU WKDQ FP JRXUPHW SODWHV SDVWD SODWHV GLQQHU SODWHV FDQ EH FOHDQHG ZLWK WKH DLG RI WKH VSUD\ KHDG 7R G
$TXD6WRS JXDUDQWHH EPFT OPU BQQMZ UP BQQMJBODFT XJUIPVU "RVB4UPQ *O BEEJUJPO UP XBSSBOUZ DMBJNT BHBJOTU UIF TFMMFS CBTFE PO UIF QVSDIBTF DPOUSBDU BOE JO BEEJUJPO UP PVS BQQMJBODF XBSSBOUZ XF XJMM QBZ EBNBHFT VOEFS UIF GPMMPXJOH DPOEJUJPOT *G PVS "RVB4UPQ TZTUFN JT EFGFDUJWF BOE DBVTFT XBUFS EBNBHF XF XJMM NBLF HPPE UIF EBNBHF GPS QSJWBUF VTFST 5P FOTVSF XBUFS EBNBHF QSPUFDUJPO UIF BQQMJBODF NVTU CF DPOOFDUFE UP UIF QPXFS TVQQMZ 5IJT MJBCJMJUZ HVBSBOUFF JT WBMJE GPS UIF TFSWJDF MJGF PG UIF
