Use and Care Manual
Table Of Contents
- Table of contents
- en-us Operating instructions
- ( Safety Definitions 5
- ( IMPORTANT SAFETY INSTRUCTIONS 6
- ƒ Causes of Damage 11
- * Getting Started 12
- , Rinse Aid 15
- - Loading the Dishwasher 17
- . Detergent 28
- / Dishwasher Cycles 30
- 0 Dishwasher Cycle Options 31
- 1 Operating the Dishwasher 34
- 2 Care and Maintenance 38
- 3 Troubleshooting 42
- 4 Customer Service 49
- ‡ Statement of Limited Product Warranty 50
- ( Safety Definitions
- en-us Operating instructions
- ( IMPORTANT SAFETY INSTRUCTIONS
- IMPORTANT SAFETY INSTRUCTIONS
- READ AND SAVE THESE INSTRUCTIONS
- To reduce the risk of fire, electrical shock, or serious injury, observe the following:
- 9 WARNING
- 9 WARNING
- 9 WARNING
- 9 WARNING
- 9 WARNING
- 9 WARNING
- 9 CAUTION
- ƒ Causes of Damage
- * Getting Started
- , Rinse Aid
- Rinse Aid
- Note:
- Adding rinse aid
- NOTICE
- 1. Open the rinse aid dispenser 92 by pressing on the latch of the lid and pull it open.
- 2. Add liquid rinse aid to the dispenser 92 until it is full. Do not overfill. Avoid spilling into air vent hole.
- 3. Close the lid. Lid must be fully closed until it clicks in order to seal.
- 4. Wipe up any excess rinse aid that may have puddled when the dispenser reservoir is full.
- Tip:
- NOTICE
- Setting the amount of rinse aid used
- Setting
- Amount
- 1. Press the On/Off button (.
- 2. Hold down the function key # and press the Start button P until the display 8 indicates •:‹x or š:‹x (x can be any number). Release both buttons.
- 3. Press the function key # until the display 8 shows §:‹†.
- 4. Press the function key 3 to select the desired setting.
- 5. Press the Start button P to save the setting.
- Turning off rinse aid indicator
- - Loading the Dishwasher
- 9.4 in (24 cm)
- 12.6 in (32 cm)
- 10.4 in (26.5 cm)
- 11.8 in (30 cm)
- 11.4 in (29 cm)
- 10.6 in (27 cm)
- 7 in (18 cm)
- 12.6 in (32 cm)
- 8 in (20.5 cm)
- 11.8 in (30 cm)
- 9 in (23 cm)
- 10.6 in (27 cm)
- RackMatic®
- Rack accessories
- Removing/Installing third rack
- Removing third rack 1*
- Installing third rack 1*
- 1. Pull out third rack rails all the way (1).
- 2. Insert third rack at an angle. Make sure that the stopper hooks of both rails slide in between the holding hooks and the lower rollers of the third rack (2).
- 3. Slide third rack in and lift the upper rollers over the front stopper hooks of both rails (3).
- 4. Push in third rack (4).
- Removing/Installing upper rack with Rackmatic®
- Removing upper rack 12
- Installing upper rack 12
- 1. Pull out upper rack rails all the way (1).
- 2. Insert upper rack at an angle. Make sure that the stopper hooks of both rails slide in between the upper and lower rollers on the rear side of the rack (2).
- 3. Slide upper rack in and lift the upper rollers over the front stopper hooks of both rails (3).
- 4. Push in upper rack (4).
- . Detergent
- / Dishwasher Cycles
- The Energy Guide label was based on the Normal soil sensing cycle as follows: The unit was tested without any rinse aid (liquid) in the rinse aid dispenser 92. A single dose of detergent was inserted into the detergent dispenser 9:, with no detergent...
- Only sanitizing cycles have been designed to meet the requirements of Section 6 of the NSF/ANSI Standard for Residential Equipment for soil removal and sanitization efficacy. There is no intention, either directly or indirectly, to imply that all cyc...
- 1 Operating the Dishwasher
- Operating the Dishwasher
- 9 WARNING
- Protection against unintentional operation
- Operating the touch buttons
- AquaSensor
- Switching the appliance on
- Time display
- Delay start
- Wash cycle end
- Auto power off
- To change the setting:
- 1. Press the On/Off button (.
- 2. Hold down the function key # and press the Start button P until the display 8 indicates š:‹x (x can be any number).
- 3. Release both buttons.
- 4. Press the function key # until the display 8 indicates ˜:‹x.
- 5. Press the function key 3 until the display corresponds with your requirements.
- 6. Press the Start button P.
- To change the setting:
- Switching off the appliance
- Interrupting the wash cycle
- 9 CAUTION
- Terminating the wash cycle (Reset)
- Changing the wash cycle
- Child Lock (panel lock)
- Intensive drying
- 1. Press the On/Off button (.
- 2. Hold down function key # and press Start button P until the display 8 indicates š:x (x can be any number).
- 3. Release both buttons.
- 4. Press function key # until the display 8 indicates the factory set value š:‹‹.
- 5. Press function key 3 to switch the intensive drying feature on š:‹‚ or off š:‹‹.
- 6. Press Start button P to save setting.
- 2 Care and Maintenance
- 3 Troubleshooting
- --------
- 4 Customer Service
- ‡ Statement of Limited Product Warranty
- 1 Operating the Dishwasher
Operating the Dishwasher en-us
35
Note: Your dishwasher is protected
against unintentional operation. If the
appliance door remains open for
more than 4 seconds after pressing
the Start button, the operation will be
paused. Close the appliance door
and press the Start button P again.
Time display
When a wash cycle is selected the
remaining wash cycle time is shown
on the display 8.
The wash cycle time is determined
during the wash cycle by the water
temperature, the amount of dishes,
as well as the degree of soiling and
may vary (depending on the selected
wash cycle).
Delay start
You can delay the start of the cycle in
one hour increments up to 24 hours.
To set Delay start:
1.
Press On/Off button (. Select a
cycle.
2.
Press Delay button @ until the
displayed time corresponds with
your requirements.
3.
Press Start button P to activate
Delay start.
To cancel Delay start:
1.
Press Delay button @ until œ:‹‹
is indicated on the digital
display 8.
2.
Press Start button P to save
setting.
Note: Your dishwasher is protected
against unintentional operation. If the
appliance door remains open for
more than 4 seconds after pressing
the Start button, the operation will be
paused. Close the appliance door
and press the Start button P again.
Wash cycle end
The wash cycle has ended when the
display 8 reads ‹:‹‹.
Auto power off
This setting determines the length of
time the control panel stays
illuminated after the cycle is
complete. To save energy the
recommended setting is ˜:‹‚.
This setting can be adjusted from
˜:‹‹ to ˜:‹ƒ.
To change the setting:
1.
Press the On/Off button (.
2.
Hold down the function key #
and press the Start button P
until the display 8 indicates
š:‹x (x can be any number).
3.
Release both buttons.
4.
Press the function key # until
the display 8 indicates ˜:‹x.
5.
Press the function key 3 until
the display corresponds with your
requirements.
6.
Press the Start button P.
œ:‹‚ 1 hour delay
œ:ƒ… 24 hours delay
˜:‹‹ dishwasher does not turn off
automatically
˜:‹‚ dishwasher turns off
automatically after 1 minute
˜:‹ƒ dishwasher turns off
automatically after
120 minutes (2 hours)