YOUR LIFE. OUR INSPIRATION.
Tabme of Contents important / Important Safety hstructions instructions IMPORTANT * The dishwasherdrain To avoid possible injury or property damage, OBSERVE ALL WARNINGS AND CAUTIONS. These instructions are intended for use by qualified installers onty. The dishwasher must be installed by a qualified serqce technician. o in addition to these instructions, the dishwasher shah be installed to meet aH eUectrbaUand pUumbingcodes and ordinances (both nationaUand bcaU).
Tools and Materials TOOLS Needed NEEDED Hammer Hob Saw Tape Measu re Sbt Screwdriver Wire Cutter Wire Stripper MATERIALS Adjustabb Wrench PhHHpsScrewdriver DrHI _- Z %20 Screwdriver i Level NEEDED (Additional materiab may be required to comply with bcal codes,) Ebctrbal Supply CaNe - Minimum #14 AWG, 2 conductor, 1 ground, insulated copper conductors rated 75°C or higher, _> Hot Water Supply Line - Minimum 3/8" O,D, copper tubing or metal braided dishwasher ....... supply line, ......
Materials Supplied MATERIALS SUPPUED Accessory Parts Supplied Accessory parts for your dishwasher come in one or more pUastic bags that are outlined bebw. NOTE: Make sure you save aHthe bags until you have compbted your installation. NOTE: Always use the suppibd or recommended hardware.
EncBosure Preparation 23-9/I 6" I_(598mm) I" ElectricaJ Shock Hazard To avoid eJectricaJ shock, make sure the water supply and electrical suppJy are shut off before installation or service. ENCLOSURE (89z}mrn) PREPARATmON mIR_mum v 23-5/8" NOTE: This dishwasher is designed to be enclosed on the top and both sides by standard residentiaU kitchen cabinetry. I - 24-1/4" (600-616 rY_f]q Figure 1 clearance between dishwasher Check door and wall --I ElectricaJ Shock/Fire Countertop Figure 2 i\
Electrical Shock Hazard To avoid electdcaJ shock, do not work on an energized circuit. Doing so could resuJt in serious injury or death. Onty qualified electricians should perform electrical work. Do not attempt any work on the dishwasher etectric suppty circuit until you are certain the circuit is 30 _E (762mm) 21 EE (533mm) de-energized. Figure 4 Fire Hazard Dishwasher Velts 120 E_ectrica_ Rating Amperes 60 15 3" Watts 1,450 (max) A,, 1 ( 75mm ° lOOmm 1.
Plumbing Preparation PLUMBING i355mm) Hot Water Supply Line Figure 6 PREPARATmON Scald Hazard To avoid being scaJded, do not perform any work on a charged hot water tine. Serious injury could result. Only qualified plumbers should perform pJumbing work. Do not attempt any work on the dishwasher hot water supply pJumbing until you are certain the hot water supply is shut off. Temperatures required for so(dedng and sweating wil( damage the dishwasher's base and water inJet va(ve.
Plumbing Preparation/Dishwasher AirGap Preparation PLUMBING PREPARATmON (continued) Drain Ptumbing Under Sink Drain Connection ff the dishwasher is to drain either directUy into the househoUd drain pUumbing or through an air gap, install a y-branch taHpbce under the sink as shown in Figure 7, installing an Air Gap if local ordinances require an air gap, as shown in Figure 8, install it according to the manufacturer's instructions, Figure 8 Disposer Make sure to remove the disposer's dishwasher drai
Dishwasher Preparation DmSHWASHER PREPARATmON (continued) Removing the Toe Pane1 FleguJar Toe PaneJ The toe paneHis HooseHyattached with tape, Remove the tape and puHH the toe paneHaway from the dishwasher, Set the toe paneHaside, HtwHHbe reinstaHHedHater, PJastic Base Access Panel and Toe PaneJ (SHY660, SHX99A, SHE660, SHE990, SHX570, and SHV570 modeJe only) The pHasticbase access paneHand toe paneHare in pHace on the dishwasher, but are not attached, Remove the toe paneHfirst, as shown in Figure 12,
Door Paneminstallation . ; ram) _ 23-1/16" (5s6 J Figure 16 PANEL mNSTALLATmON SH U/SH E ModeJs - Accessory Panel lnstaJtation Ufyou have an SHU/SHE modeUand have ordered an accessory paneUkit, install the paneUprior to sliding the dishwasher into pUace.The paneUdimensions are shown in Figure 16. 1/4" max, _ DOOR SHI Modets - Panet Installation SHUmodeUscome with additionaU mounting hardware and a tempUate sheet with installation instructions.
PlacingtheDishwasher/Securing theDishwasher PLACmNG THE DISHWASHER 1 Straighten and position the hot water supply line and the electrical supply cable as shown in Figure 19 so that they wiii align with their channels under the dishwasher base, _L 2 Position the dishwasher close enough to the enclosure so that you can run the dishwasher drain hose to the under sink drain connection, Make certain that the hot 14" 355mm) _/ J Figure 19 SECURING Hot Water Supply Line and Electrical Supply Cable Positio
Drain Hose Connection 2 After the unit is instafled in the enclosure, bvebd and secured, lock the two front bg bvebrs in place by driving the enclosed bg bvebr locking screws into each screw boss located in front of the bvebrs, See Figure 23, 3 Tighten screws until they are flush with the surface of the bosses, Leg Leveler Locking Screw mnstaHation of the Rubber Adaptor Y • Screw Boss Figure 23 Drain Hose 1 Obtain the Rubber Drain Hose Adaptor and the two hose damps from the Dishwasher Instaflation K
Hot Water Connection HOT WATER CONNECTmON Scald Hazard To avoid being scaJded, do not perform any work on a charged hot water tine. Serious injury could result. Only qualified plumbers shouJd perform pJumbing work. Do not attempt any work on the dishwasher hot water supply pJumbing until you are certain the hot water supply is shut off.
Electrical Connection ELECTFiICAL CONNECTmON Electrical Shock Hazard To avoid ebctricaJ shock, do not work on an energized circuit. Doing so could result in serious injury or death. OnJy quaJified eJectricians shouJd perform ebctrical work. Do not attempt any work on the dishwasher electric suppJy circuit until you are certain the circuit is de-energized. Fire Hazard Figure 28 To avoid a fire hazard, make sure eJectricaJ work is properly installed.
EmectricalConnection/Door -_ Tension Adjustment/Base and Toe Panel ELECTRICAL CONNECTmON (continued) Fire Hazard To avoid a fire hazard, make sure there are no toose eJectrical connections. Make sure aH etectricaJ connections are properly made.
Base and Toe Pane,/Final Instructions BASE AND TOE PANEL (Continued) PJaetic Base Access PaneJ and Toe PaneJ installation (SHY66C, SH×99A, SH E66C, SHE99C, SH×57C, and SHV57C modete only) 1 PUacethe PUastb Base Access PaneUunder and up the front bottom paneUof the dishwasher, as shown in Figure 34a, 2 insert the PUastb Base Access PaneUscrews into the PUastb Base Access PaneU, as shown in Figure 34b, Tighten the PUastb Base Access PaneUScrews, 3 PUace the Cotton UnsuUationStrip under the unit, between
Customer CUSTOMER Service SERVmCE Your Bosch dishwasher requires no special care other than that described in the Care and Cleaning section of the Use and Care Manual, if you are having a problem with your dishwasher, before calling for service please refer to the SelfHelp section of the Use and Care Manual, if service is necessary, contact your dealer or installer or an authorized service center, Do not attempt to repair the appliance yourself, Any work performed by unauthorized personnel may void the
Notes
Notes
Notes
© BSH Home Appliances 90 00 06 37 16 (8504) Corporation 2005 • Litho U,S,A, 07/04
