BOSCH YOUR UFE.
Table of Contents / Important Instructions BOSCH Tgtjli- Qfveàîitèrits; III .>•= = j, , . *:= .G ^f4=.= W .. P .1 ■ ■ ■ ■ TpoliN3o*d; ;.:..:G;.'.;,; :V.:7;';::-.tG.Gh.t2:7GL: .■ .■ .-GsoUfing rpe .u;;snvrasnor:: ■ .:,v\ Mi^ÈpriaiPTîeedpd ::■ J ;v/.-.-.;:(.Gt.;GG.(.:;;v.',:/;..-.).:2.GGG^ l7.,T)iaih V ëTçbsuæ; pToparsri&n; ; d ploii'WiàprvîonrreçfeR 3 G o r i n w d i o n . V.P,:G G G ; VGpOGrTGSlS:0;lF.d;UsF 7//; Btçp and Goë'Panéi: •G-TG,;: Oi pciricà I Ftrepa;faEieR V. ;.
Tools and Materials Needed f MATERIALS NEEDED (Additional materials may be required to comply with local codes.) Electrical Supply Cable - Minimum #14 AWG, 2 conductor, 1 ground, insulated copper conductors rated 75°C or higher. Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line. Shut-off valve and fittings appropriate for hot water supply line (copper tubing/ compression fitting, or braided hose). 90° elbow with 3/8” N.P.T.
Materials Supplied MATERIALS SUPPLIED Accessory Parts Supplied Accessory parts for your dishwasher come in one or more plastic bags that are outlined below. fslOTE: Make sure you save all the bags until you have completed your installation. NOTE: Always use the supplied or recommended hardware.
Enclosure Preparation ikWARNIN I Electrical Shock Hazard To avoid electrical shock, make sure the water supply and electrical supply are shut off before installation or service. ENCLOSURE PREPARATION NOTE: This dishwasher is designed to be enciosed on the top and both sides by standard residentiai kitchen cabinetry. Select a location as close to the sink as possible for easy access to water supply and drain lines.
Electrical Preparation ELECTRICAL PREPARATION AWARNIN __________ 1 Electrical Shock Has tard To avoid eilectrical shock, do not work on an energized circuit. Doing so coulci result in serious injury ordieath. Only qualified elcsctricians should perform elMetrical work. Do not a1Hempt any work on the dis:hwasher electric suppi y circuit until you are certair1 the circuit is de-energi2 :ed.
Plumbing Preparation PLUMBING PREPARATION m ikWARNIN rt Scald Hazard To avoid being scalded, do not perform any work on a charged hot water line. Serious injury could result. Only qualified plumbers should perform plumbing work. Do not attempt any work on the dishwasher hot water supply plumbing until you are certain the hot water supply is shut off. CAUTIO Li n Temperatures required for soldering and sweating will damage the dishwasher’s base and water inlet valve.
Plumbing Preparation/ Dishwasher Preparation PLUMBING PREPARATION (continyed) Drain Plumbing Under Sink Drain Connection If the dishwasher is to drain either directly into the household drain plumbing or through an air gap, install a y-branch tailpiece under the sink as shown in Figure 7. Installing an Air Gap If local ordinances require an air gap, as shown in Figure 8, install it according to the manufacturer’s instructions.
Dishwasher Preparation DISHWASHER PREPARATION (continued) Removing the Toe Panel Regular Toe Panel The toe panel is loosely attached with tape. Remove the tape and pull the toe panel away from the dishwasher. Set the toe panel aside. It will be reinstalled later. Plastic Base Access Panel and Toe Panel (SHY66C, SHX99A, SHE66C, SHE99C, SHX57C, and SHV57C models only) The plastic base access panel and toe panel are in place on the dishwasher, but are not attached.
Door Panel Installation DOOR PANEL INSTALLATION SHU/SHE Models - Accessory Panel Installation If you have an SHU/SHE model and have ordered an accessory panel kit, Install the panel prior to sliding the dishwasher into place. The panel dimensions are shown in Figure 16. SHI Models - Panel Installation SHI models come with additional mounting hardware and a template sheet with installation instructions. The stain less steel models of the SHI series also come with two extension pieces.
Placing the Dishwasher/ Securing the Dishwasher PLACING THE DISHWASHER 1 Straighten and position the hot water supply line and the electrical supply cable as shown in Figure 19 so that they will align with their channels under the dishwasher base. 2 Position the dishwasher close enough to the enclosure so that you can run the dishwasher drain hose to the under sink drain connection.
Drain Hose Connection 2 After the unit is installed in the enclosure, leveled and secured, lock the two front leg levelers in place by driving the enclosed leg leveler locking screws into each screw boss located in front of the levelers. See Figure 23. 3 Tighten screws until they are flush with the surface of the bosses. installation of the Rubber Drain Hose Adaptor 1 Obtain the Rubber Drain Hose Adaptor and the two hose clamps from the Dishwasher Installation Kit.
Hot Water Connection HOT WATER CONNECTION AWARNIN Scald Hazard To avoid being scalded, do not perform any work on a charged hot water line. Serious injury could result. Only qualified plumbers should perform plumbing work. Do not attempt any work on the dishwasher hot water supply plumbing until you are certain the hot water supply is shut off.
Electrical Connection ELECTRICAL CONNECTION AWARNIN Strain . Relief Plate * :t Electrical Shock Hazard To a¥oid electrical shock, do not work on an energized circuit. Doing so could result in serious injury or death. Only qualified electricians should perform electrical work. Do not attempt any work on the dishwasher electric supply circuit until you are certain the circuit is de-energized.
Electrical Connection/ Door Tension Adjustment/ Base and Toe Panel ELECTRICAL CONNECTION (continued) ikWARNIN I Fire Hazard To avoid a fire hazard, make sure there are no loose electrical connections. Make sure all electrical connections are properly made. Do not pre-twist the wires before connecting them with wire nuts. ® Extend the dishwasher’s stranded wires 1/8” (3mm) beyond the power supply cable’s solid wires, as shown in Figure 30.
Base and Toe Panel/ Final Instructions BASE AND TOE PANEL (Continyed) Plastic Base Access Panel and Toe Panel Installation (SHY66C, SHX99A, SHE66C, SHE99C, SHX57C, and SHV57C models only) 1 Place the Plastic Base Access Panel under and up the front bottom panel of the dishwasher, as shown in Figure 34a. 2 Insert the Plastic Base Access Panel screws into the Plastic Base Access Panel, as shown in Figure 34b. Tighten the Plastic Base Access Panel Screws.
Customer Service CUSTOMER SERVICE Your Bosch dishwasher requires no special care other than that described in the Care and Cleaning section of the Use and Care Manual. If you are having a problem with your dishwasher, before calling for service please refer to the Self Help section of the Use and Care Manual. If service is necessary, contact your dealer or installer or an authorized service center. Do not attempt to repair the appliance yourself.
Notes
Notes
Notes
€> BSH Home Appliances Corporation 2005 • Litho U.S.A.
