Data Sheet

The VG4-SFPSCKT and CNFE2MC/IN media converters
accept the following SFP modules:
Module
Fiber Type Optical Interface
SFP-2
MMF Duplex LC
SFP-3 SMF Duplex LC
SFP-25 MMF Single SC
SFP26
MMF Single SC
The SFP-25/SFP-26 modules are counterparts; if you
use one in the VG4-SFPSCKT module, then you must
use the other in the CNFE2MC/IN head-end unit. Refer
to the chart below for the acceptable combinations.
Compatibility Chart
If this SFP module is used with
the VG4-SFPSCKT
Then this SFP module must be used in
the CNFE2MC/IN
SFP-2 SFP-2
SFP-3 SFP-3
SFP-25
SFP-26
SFP-26 SFP-25
C1-IN Rack Mount Card Cage
The C1-IN rack mount card cage is designed to hold a
maximum of 14 CNFE2MC/IN modules. The C1-IN card
cage utilizes an integral, yet field replaceable universal
power supply suitable for 120 VAC to 240 VAC,
50/60 Hz operation.
The C1-IN unit includes automatic self-resetting
current overload protection, so a fault in any one
module will not cause the entire card cage to shut
down.
C1-BP Closure Panel
The C1-BP is a closure panel for the C1-IN rack mount
card cage, providing coverage for one rack slot.
Installation/configuration notes
The Bosch Fiber Optic Media Converter solution
consists of three core components and several
optional components to help fit every application.
To provide fiber optic communications between a
Bosch VG4 AutoDome and a controller, you must use
the following:
•
One (1) VG4-SFPSCKT Fiber Optic Ethernet Media
Converter
Kit – a printed circuit board installed inside
a VG4 power supply box. (See Technical Specification
Section 1)
• One (1) CNFE2MC/IN Ethernet Fiber Optic Media
Converter – a rack-mounted or surface mounted head-
end controller. (See Technical Specification Section
2)
• Two (2) Small Form-factor Pluggable (SFP) modules –
one module is installed in the VG4-SFPSCKT, the
other is installed in the CNFE2MC/IN. (See Technical
Specification Section 3)
Optionally, you can use the following modules to
customize your installation:
• C1-IN Rack Mount Card Cage (See Technical
Specification Section 4)
• C1-BP Closure Panel
To provide fiber optic communications between a MIC
Series 550, 550IR, or 612 camera and a controller, you
must use the following:
•
One (1) VG4-SFPSCKT Fiber Optic Ethernet Media
Converter
Kit – a printed circuit board installed inside
a MIC IP power supply box. (See Technical
Specification Section 1)
• One (1) Small Form-factor Pluggable (SFP) module –
one module is installed in the VG4-SFPSCKT. (See
Technical Specification Section 3)
Technical specifications
Section 1: VG4-SFPSCKT Fiber Optic Ethernet Media
Converter Kit
Description
Fiber Optic Ethernet Media Converter kit.
Requires a small form-factor pluggable (SFP)
module (sold separately).
Data Interface Ethernet
Data Rate
10/100 Mbps
IEEE 802.3 Compliant
Full Duplex or Half Duplex Electrical Port
Full Duplex Optical Port
Compatible
Receiver
CNFE2MC/IN
Installation
Installed inside a VG4-A-PA1, VG4-A-PA2,
VG4‑A‑PSU1 or a VG4‑A‑PSU2 power supply
box, or in a MIC IP PSU, with supplied mounting
hardware.
Note: Wiring for the VG4-SFPSCKT must be
routed through the proper conduit opening on
the power supply box. Refer to the installation
guide that accompanies the module.
LED Indicators
Power/Link
(on circuit board)
• Green
Power is applied, fiber link is valid
• Red
Power is applied, fiber link is missing
• Green/
Flashing
Red, rapid
Power is applied
Fiber link is valid
Data is present and video is streaming from the
camera to a network connection
• Green/
Flashing
Red, slow
Power is applied
Fiber link is valid
Data is present
Video is not streaming from the camera, or the
RJ45 connection to the camera is not valid
RJ-45 Connector
2 | Fiber Optic Media Converters