AMAX 2100 / 3000 / 4000 en Quick Start Guide
AMAX 2100 / 3000 / 4000 Table of Contents | en 3 Table of contents 1 Graphics 4 2 Safety 6 3 Short information 8 4 Installation 9 4.1 Connecting Modules and Devices 5 Configuration 10 5.1 Programming and Operating the AMAX System 10 5.1.1 Option: Changing Menu Language 10 5.1.2 Accessing the Menus 10 5.1.3 Menu Navigation 10 5.1.4 Programming the AMAX System 11 5.1.
en | Graphics 1 AMAX 2100 / 3000 / 4000 Graphics R B G R B G Y _ 900mA AUX 1: < _ 900mA AUX 2: < TIP TH RH RING Y AUX1 AUX2 AUX2 AUX1 +12V +12V - Bosch Option AUX Power _ 900mA Bus 2 < Transformer Keypads: GND AC AC 1= 2= IUI-AMAX4-TEXT IUI-AMAX3-LED16 3 = IUI-AMAX3-LED8 4= + 18VAC@50VA Battery 12V 7Ah _ 18Ah 12V < 230V ~50Hz 230mA Fuse 1 A 5-16 Inst. Guide Keypads: IUI-AMAX-LED8 IUI-AMAX-LCD8 Bosch Option _ 900mA Bus 1 < 1= 2= I/O Moduls: DX2010 DX3010 DX4010 Adr.
Graphics | en AMAX 2100 / 3000 / 4000 Risk of shock if N,L1 or is connected incorrectly. For operation safety, the ground terminals must be connected. 1 1RING 1RING TIP 5 TIP Tamper L8 COM L7 ♥ Slow flash: Normal state On: Trouble state Off: Trouble state 3 L6 1 3 2 COM L5 Zones 3 L4 2 Program Key Port COM L3 3 L2 Factory Default 2 COM L1 OPT/SDI Keypads: 1= IUI-AMAX4-TEXT 2 = IUI-AMAX3-LED16 3 = IUI-AMAX3-LED8 4= 5-8 Inst.
en | Safety 2 AMAX 2100 / 3000 / 4000 Safety Danger! Battery Consequences – Risk of shock, if N, L1 or xx is connected incorrectly! For operation safety, the ground terminals must be connected. 1. Be careful when connecting the positive (red) wire and the "BATT +" port of the AMAX panel. If short-circuiting with the "BATT +" port of the AMAX panel or the housing, electric arc will occur! 2. To remove the battery from the AMAX panel, first disconnect the positive wire of the battery. 3.
AMAX 2100 / 3000 / 4000 – Safety | en 7 This system / product must be installed and maintained by a qualified installer / service person. – Bosch recommends testing the whole alarm system at least once a week. – Maintenance should be done by a qualified installer / service person four times a year. – The system / product must be connected to a socket-outlet with a protective earth contact. 4 Switch off the AMAX power supply during installation and wiring to prevent equipment damage.
en | Short information 3 AMAX 2100 / 3000 / 4000 Short information This Installation Quick Guide is provided with the AMAX 4000 system and contains information on how to get the system into operation easily and quickly. The guide describes the main steps required for basic system installation and setup of the AMAX panel 4000 together with one IUI-AMAX4-TEXT keypad and one RFRC-OPT RADION receiver. The program tree structure is provided at the end of this guide.
AMAX 2100 / 3000 / 4000 Installation | en 4 Installation 4.1 Connecting Modules and Devices 9 The AMAX panel 4000 provides Option Bus 1 and Option Bus 2 to connect modules and devices. Each module may be connected to each bus. The maximum number of modules per Option Bus = 14, thereof 8 keypads. The following overview displays the maximum number of modules that may be connected.
en | Configuration AMAX 2100 / 3000 / 4000 5 Configuration 5.1 Programming and Operating the AMAX System The AMAX system can be programmed and operated over menus by using keypads and/or the A-Link Plus remote programming software on a PC via the USB interface. After all modules and devices have been installed, the AMAX panel indicates the system status by the LED status indicator on the system main board.
AMAX 2100 / 3000 / 4000 Configuration | en 11 Confirming the Input 4 Press the [#] key to confirm the input. Switching between Settings 4 Press and hold the [*] key for 3 seconds to switch between settings. Operating a Menu 1. Operate according to the menu prompt. Select the menu and enter data for specific programming items according to the display on the keypad to complete the programming, step by step. 2. Press the [#] key to confirm each step. Exiting the Programming Mode 1.
en | Configuration AMAX 2100 / 3000 / 4000 Sample: Enabling the RF Device for Wireless Communication 1. Enter the Installer Code [1234] + [958] and press the [#] key. 2. Navigate to the RF MANAGER menu and press the [#] key. The system guides you through the menu and displays the next menu item: RF SETTING. 1. Press the [#] key to get to the next menu item: RF RECEIVER. 2. Press the [#] key to get to the next menu item: RF RECEIVER ENABLE. 3.
AMAX 2100 / 3000 / 4000 5.1.5 Configuration | en 13 PC Programming via USB Interface By using the A-Link Plus remote programming software on a PC, the AMAX panel configuration can be remotely programmed or controlled. For direct communication, the PC and the AMAX panel have to be connected to each other by the USB cable. Installing the Programming Software 4 Double-click on the A_Link_setup.exe file to install the programming software on the PC.
en | Configuration AMAX 2100 / 3000 / 4000 Figure 5.2: Setting Direct Link Port Option: Creating a New Customer If necessary, create a new customer. 4 Select Customer – New Customer from the menu bar. The Customer Information dialog opens. Figure 5.3: Entering Customer Information 1. Enter the customer name in the Customer Name entry field to create a new customer. 2. Enter other relevant customer information. The Customer Number must be entered.
Configuration | en AMAX 2100 / 3000 / 4000 15 Figure 5.4: Configuring the Control Panel 2. Select AMAX4000 as Control Panel Type. 3. Make sure that the value under Subscribed Number for Destination 1 is the same as currently programmed in the AMAX panel as Receiver 1. The value is 000000, if the firmware of the AMAX panel was upgraded or the AMAX panel has factory settings. 4. Bosch Sicherheitsysteme GmbH Select the System Options item in the same tab. Quick Start Guide 2014.
en | Configuration AMAX 2100 / 3000 / 4000 Figure 5.5: Checking the System Options 5. Make sure that the value for the Installer code parameter is the same as currently programmed in the AMAX panel. The value is 1234, if the firmware of the AMAX panel was upgraded or the AMAX panel has factory settings. Establishing a Direct Connection 1. Select the Link tab to establish a connection between the A-Link Plus program and the AMAX panel. 2014.
Configuration | en AMAX 2100 / 3000 / 4000 17 Figure 5.6: Establishing a Direct Connection 2. Select Direct Connect as communication model. 3. Click on the Connect button to connect to the AMAX panel. Bosch Sicherheitsysteme GmbH Quick Start Guide 2014.
en | Technical Data 6 AMAX 2100 / 3000 / 4000 Technical Data Panel Enclosure: Dimensions (HxWxD): – 375 x 322 x 88 mm(L x W x H) Weight: – 4700g Relative Humidity: – 10%-95% Operating Temperature: – -10°C - +55°C – 2 wire fire zone or Single or dual end-of-line (EOL Environmental Considerations: Supervised Zones: Onboard: Z1: 2,2KΩ) tamper point support Z2 - Z16 COM: – 15 Single or dual end-of-line (EOL 2,2KΩ) tamper point support Tamper: – Enclosure tamper input (does not reduce
AMAX 2100 / 3000 / 4000 Technical Data | en B 426 or DX 4020 or DX – 2 DX2010: – 6 DX 4010: – 1 RF Receiver: – 1 RF Repeater: – DSRF = 0, Radion = 8 RF Sensors: – 64 RF Keyfobs: – DSRF = 24, Radion = 128 Power Supply Type: – EN = A Transformer: – 230V Input/18VAC 50VA Fuse=1A AC Input: – AC Input Voltage: 195 VAC to 253 VAC – Line Voltage Frequency: 50 Hz – maximum current for all components 2000mA – max current for all components Battery 7Ah standby 19 4020G (only 1):
en | Technical Data AMAX 2100 / 3000 / 4000 Panel PCB: – Quiescent current maximum 100mA Battery: – 12V/7 Ah, lead acid rechargeable – 12V/17Ah, lead acid rechargeable – Low battery condition is below 11,0 VDC – Minimum battery condition is 10,8VDC – EN 50131-3 Grade-3 Environmental Class-II Certification: Keypads: IUI-AMAX4-TEXT (LCD Text Keypad) Relative Humidity: – 10%-95% Operating Temperature: – -10°C - +55°C Input Voltage range: – 10.8VDC - 13.
AMAX 2100 / 3000 / 4000 Current Consumption: Technical Data | en 21 – standby 31mA – maximum 60mA – four wire, AWG18 or AWG22 – maximum length 200m (Panel to last KP) – maximum BUS 1 length 700m (max 14 devices, 8 KPs) – maximum BUS 2 length 700m (max 14 devices, 8 KPs) EN type: – EN = B, IK = 06, IP = 30 Certification: – EN 50131-3 Grade-3 Environmental Class-II Cable requirements: Bosch Sicherheitsysteme GmbH Quick Start Guide 2014.
Bosch Sicherheitssysteme GmbH Robert-Bosch-Ring 5 85630 Grasbrunn Germany www.boschsecurity.
