This cooktop is for use with Natural Gas and Universal LPG Leave this instructions with the owner PPH616B21A, PPQ716B21A USER INSTRUCTIONS INSTALLATION INSTRUCTIONS MAINTENANCE INSTRUCTIONS
Ú Table of contents ecuIn[rotis]deumyosjatn Safety considerations................................................................ 2 For your safety.....................................................................................2 What to do if you smell gas ..............................................................2 Warnings...............................................................................................2 Installation ..................................................................
Note: To avoid jeopardising the electrical safety of the appliance, it is forbidden to use high-pressure or steam jet cleaning devices. SHOULD THE RELEVANT CONDITIONS NOT BE PROPERLY SATISFIED, THE INSTALLER, AND NOT THE MANUFACTURER, SHALL HELD LIABLE. Installation Statutory requirements Preparing to install This installation must conform with the following: Refer to AS/NZS 5601.1 for piping size details. These built-in cooktops are intended to be inserted in a benchtop cutout.
Before connecting the unit, check whether the local connection conditions (type of gas) are compatible with the unit’s setting. Observe any special conditions imposed by local suppliers (utilities). The specifications of this cooktop are stated on the data label located on the bottom of the cooktop base. A duplicate data label is supplied for adhesion to an accessible location near the hotplate if the data label on the base of the hotplate cannot be accessed when the hotplate is installed.
with the most suitable glue (code 310818). Please note the manufacturers instructions for use. Fit regulator (N.G.) or a test point (Universal LPG) directly to the R 1/2’’ connection. 4. Smooth the silicone adhesive with a scraper or wet finger moistened with soap and water before it forms a layer. 5. Allow the silicone adhesive to dry before using the appliance. VLOLFRQH Direction of gas flow is indicated on the rear of the regulator.
Converting the cooktop from Nat. Gas to Universal LPG Adjustment of the taps To change injectors 2. Remove the control knobs from the taps. It has a flexible All work involved in installation, setting and adaptation to a different gas type must be carried out by authorised personnel from our Service Centre and must comply with current regulations and the conditions laid down by the local gas company. 1. Set the control knobs to minimum. rubber valve reinforcing ring.
Operating instructions Burner locations 334 % $ 33+ % $ 1 1 2 2 1 Pan supports 2 Control knobs 3 Auxiliary burner (up to 1 kW) 4 Semi-rapid burner (up to 1.75 kW) 5 Rapid burner (up to 3 kW) 6 Double-flame wok burner (up to 3.3 kW) 7 Triple-flame wok burner (up to 4 kW) Accessories The following accessories can be purchased from the Technical Assistance Service: Additional wok pan support Simmer Cap Only for use on wok burners with pans with a round base.
Operation Safety system There are indications to show which burner each control knob operates. Depending on the model, your hob may have a safety system (thermocouple) that prevents the flow of gas if the burners accidentally switch off. It is essential to ensure that all the burner parts and pan supports are correctly installed for the appliance to work correctly. Do not swap the burner caps around. WKHUPRFRXSOH LJQLWLRQ VSDUNHU To ensure that this device is active: 1. Switch on the burner as usual.
Cooking recommendation Burner Very high - High Medium Wok burner Boiling, steamReheating and keeping ing, griddling, things hot: cooked and pretoasting, paellas, cooked dishes Asian food (wok). Do not cook without using a lid and make sure the lid is properly fitted. This wastes energy.
Maintenance Always clean off any liquid as soon as it is spilt. This will prevent food remains from sticking to the hob surface and you will save yourself any unnecessary effort. Never slide pans across the glass surface, as you may scratch it. In addition, try not to drop heavy or sharp objects on the glass. Never strike any part of the hob. Grains of sand that may come from cleaning fruits and vegetables will scratch the glass surface.
Wiring diagram A Switch B Blue wire C Brown wire D Terminal E Ignition module www.bosch-home.com '( ! 01 & ! : PPH616B21A ULPG 12 Test point pressure (kPa) Injectors marks 90 LHF 50 67 120 LHR RHF 67 120 85 155 RHR 100 C 182 39.10 ,56. 43.40 In compliance with AS/NZS 3100 and AS 4551:2008 Preinstalled NG 220-240V, 0.
Robert Bosch Hausgeräte GmbH Carl-Wery-Straße 34 81739 München Germany www.bosch-home.
