Operation Manual
Table Of Contents
- [en] Instructions for installation and use
- Ú Table of contents[en] Instructions for installation and use
- Installation instructions
- Assembly
- Important notes
- Preparation of assembly kitchen units, figures 1/2/3/4
- Installing the appliance, figures 5/7
- Changing the intensity of the 13 / 16 Amp connection current, figure 8
- 1. Turn on the hob with the main switch. Do not place any pans on the hotplates
- 2. Within the following 60 seconds, adjust all hotplates to the desired power level according to the required connection current (see table).
- 3. Turn off all the hotplates in sequence, starting from the lower right and continuing anticlockwise.
- 4. The selected connection current is indicated in the display of the right-hand lateral hotplates.
- 5. Turn off the hob with the main switch.
- Uninstalling the appliance
- Instruction manual
- Produktinfo
- : Safety precautions
- Please read this manual carefully. Please keep the instruction and installation manual as well as the appliance certificate in a safe place for later use or for subsequent owners.
- Check the appliance after removing it from the packaging. If it has suffered any damage in transport, do not connect the appliance, contact the Technical Assistance Service and provide written notification of the damage caused, otherwise you will los...
- This appliance must be installed according to the installation instructions included.
- This appliance is intended for domestic use only. The appliance must only be used for the preparation of food and drink. The appliance must be supervised during operation. Only use this appliance indoors.
- Do not use covers. These can cause accidents, due to overheating, catching fire or materials shattering, for example.
- Do not use inappropriate child safety shields or hob guards. These can cause accidents.
- This appliance is not intended for operation with an external clock timer or a remote control.
- This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capabilities or by persons with a lack of experience or knowledge if they are supervised or are instructed by a person responsi...
- Children must not play with, on, or around the appliance. Children must not clean the appliance or carry out general maintenance unless they are at least 8 years old and are being supervised.
- Keep children below the age of 8 years old at a safe distance from the appliance and power cable.
- We advise that you exercise caution using or standing near an induction hob while it is in operation, if you wear a pacemaker or a similar medical device. Consult your doctor or the device manufacturer concenring its conformity or any possible incomp...
- Risk of fire!
- Risk of burns!
- Risk of electric shock!
- ■ Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker...
- Risk of electric shock!
- Risk of electric shock!
- Risk of electric shock!
- Malfunction risk!
- The hob is equipped with a fan in the lower section. If there is a drawer under the hob it should not be used to store small objects or paper, since they could damage the fan or interfere with the cooling if they are sucked into it.
- There should be a minimum of 2 cm between the contents of the drawer and fan intake.
- Risk of injury!
- ■ When cooking in a bain marie, the hob and cooking container could shatter due to overheating. The cooking container in the bain marie must not directly touch the bottom of the water-filled pot. Only use heat-resistant cookware.
- Risk of injury!
- Elements that may damage the appliance
- Energy-saving advice
- Cookware
- The hotplates
- Residual heat indicator
- Set the hotplate
- Cooking guidelines table
- Childproof lock
- To deactivate
- 1. Select a hotplate.
- 2. Press the symbol boostG.
- Note
- Time programming function
- Turning off a hotplate automatically
- Time programming function
- Note
- The timer
- Hob frame
6
Important notes
Safety: Safety in use is only guaranteed if the technical
installation of the hob has been carried out correctly and in
accordance with the assembly instructions. The installation
technician shall be liable for any damage caused as a result of
unsuitable installation.
Electric connection: Only by an authorised specialist
technician. The guidelines set out by the local electricity
provider must be observed.
Type of connection: The appliance falls under protection
class I and can only be used in combination with a grounding
conductor connection.
The manufacturer accepts no responsibility for any malfunction
or damage caused by incorrect electrical installations.
Installation: The appliance must be connected to a fixed
installation and the means of disconnecting it from the fixed
installation must be installed according to the installation
instructions.
Built-in assembly under worktop: The induction hobs may
only be installed over a drawer, ovens with forced ventilation
from the same brand and dishwashers from the same brand.
Refrigerators, unventilated ovens and washing machines may
not be installed beneath the hob.
Power cable: Do not tie the power cable or pass it along sharp
edges. If there is an oven installed below, pass the cable along
the rear corners of the oven to the connection box. It must be
positioned so that it does not touch any of the hot parts of the
hob or the oven.
Hob: flat, horizontal, stable. Follow the hob manufacturer's
instructions.
Warranty: an unsuitable installation, connection or assembly
will invalidate the product warranty.
Note: Any change to the appliance's interior, including
changing the power cable, must only be performed by specially
trained members of the Technical Assistance Service.
Preparation of assembly kitchen units,
figures 1/2/3/4
Built-in kitchen units: Minimum temperature resistance of
90°C.
Gap: Remove any shavings after performing cutting work.
Cut surfaces: Seal with heat resistant material.
Assembly over drawer, figure 2a
Metal objects stored inside the drawer could become very hot
due to the air recirculating from the hob ventilation system. If
this occurs, an intermediate support is recommended.
Intermediate support: A wooden panel can be used (figure 3)
or you may order a suitable accessory from our Technical
Assistance Service. The reference code for this accessory
is 686002.
Worktop: Must have a minimum thickness of 20 mm.
The distance between the top of the working surface and the
top of the drawer must be 65 mm.
9
9
91a
1
/
D E
F G