OBJ_DOKU-10801-004.fm Page 1 Friday, September 7, 2012 12:38 PM WEU Robert Bosch GmbH Power Tools Division 70745 Leinfelden-Echterdingen Germany WEU PHO 20-82 www.bosch-pt.com 2 609 932 743 (2012.
OBJ_BUCH-631-004.book Page 3 Friday, September 7, 2012 12:39 PM |3 1 2 3 4 5 6 8 1 7 3 9 2 PHO 20-82 Bosch Power Tools 2 609 932 743 | (7.9.
OBJ_BUCH-631-004.book Page 4 Friday, September 7, 2012 12:39 PM 4| A B 8 14 14 13 8 10 10 C 11 12 11 12 D 16 Ø 35mm 15 17 1 E 23 18 20 24 19 18 19 22 20 21 2 609 932 743 | (7.9.
OBJ_BUCH-631-004.book Page 5 Friday, September 7, 2012 12:39 PM |5 F G 8 8 mm max 25 82 ma mm x H 7 45° Bosch Power Tools 2 609 932 743 | (7.9.
OBJ_BUCH-631-004.book Page 11 Friday, September 7, 2012 12:39 PM English | 11 Luxemburg Tel.: +32 2 588 0589 Fax: +32 2 588 0595 E-Mail: outillage.gereedschap@be.bosch.com Entsorgung Elektrowerkzeuge, Zubehör und Verpackungen sollen einer umweltgerechten Wiederverwertung zugeführt werden.
OBJ_BUCH-631-004.book Page 12 Friday, September 7, 2012 12:39 PM 12 | English these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. f Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f Keep cutting tools sharp and clean.
OBJ_BUCH-631-004.book Page 13 Friday, September 7, 2012 12:39 PM English | 13 Technical Data Planer Article number Rated power input Output power No-load speed Planing depth Rebating depth Planing width, max. Weight according to EPTA-Procedure 01/2003 Protection class W W min-1 mm mm mm kg PHO 20-82 0 603 365 1.. 680 320 19500 0–2 0–8 82 2.2 /II The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
OBJ_BUCH-631-004.book Page 14 Friday, September 7, 2012 12:39 PM 14 | English – As far as possible, use a dust extraction system suitable for the material. – Provide for good ventilation of the working place. – It is recommended to wear a P2 filter-class respirator. Observe the relevant regulations in your country for the materials to be worked. Clean the chip ejector 1 regularly. Use a suitable tool (e.g., a piece of wood, compressed air, etc.) to clean a clogged chip ejector.
OBJ_BUCH-631-004.book Page 15 Friday, September 7, 2012 12:39 PM English | 15 Planing with Parallel/Beveling Guide (see figures D–F) Mount the parallel guide 17 or beveling guide 21 to the machine using the corresponding fastening bolt 20. Depending on the application, mount the rebating depth stop 24 with fastening bolt 23 to the machine. Loosen the locking nut 19 and adjust the requested rebating width on the scale 18. Tighten the locking nut 19 again.
