This cooktop is for use with Natural Gas and Universal LPG PCI815B91A Robert Bosch Hausgeräte GmbH Carl-Wery-Straße 34 81739 München Cod. 9000617265 A www.bosch-home.
Content Safety considerations . . . . . . . . . . . . . . . . 5 For your safety . . . . . . . . . . . . . . . . . . . . . . . 5 What to do if you smell gas . . . . . . . . . . . . . . 5 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installation . . . . . . . . . . . . . . . . . . . . . . . . . 7 Statutory requirements . . . . . . . . . . . . . . . . . . 7 Preparing to install . . . . . . . . . . . . . . . . . . . . . . . 7 Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dear customer, Congratulations on your choice and thank you for purchasing one of our appliances. This practical, modern and functional appliance is manufactured using materials of the highest quality which are subject to strict quality control checks throughout the entire manufacturing process. The appliance is meticulously tested to ensure that it meets your demands and produces perfect cooking results. Do not remove the appliance from its protective packaging until it is installed in the unit.
Safety considerations For your safety If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. Do not store articles on or against this appliance. Do not store flammable material near this appliance. Do not spray aerosols in the vicinity of this appliance while it is in operation. What to do if you smell gas Do not try to light the appliance. Do not touch any electrical switch; do not use any phone in your building.
Important. When using a very large pot, leave a gap of at least 50 mm (2”) to avoid damaging any parts in bench top wood, plastic or other non-heat resistant materials. Never leave oil or hot fat unattended. The surfaces on heating and cooking appliances get hot when in use. Be careful. Keep children away from the appliance. Only use your appliance for the preparation of food and never for room-heating purposes. This appliance leaves the factory set for the gas supply indicated on the data label.
Installation Statutory requirements This installation must conform with the following: Ø Manufacturer’s Installation instructions Ø Local Gas Fitting Regulations Ø Municipal Building Codes, Ø Refer to AS/NZS 5601.1 for Gas Installations. Ø S.A.A. Wiring Code Ø Local Electrical Regulations Ø Any other statutory regulations Preparing to install Refer to AS/NZS 5601.1 for piping size details. These built-in cooktops are intended to be inserted in a benchtop cutout.
Before connecting the unit, check whether the local connection conditions (type of gas) are compatible with the unit’s setting. Observe any special conditions imposed by local suppliers (utilities). The specifications of this cooktop are stated on the data label located on the bottom of the cooktop base. A duplicate data label is supplied for adhesion to an accessible location near the hotplate if the data label on the base of the hotplate cannot be accessed when the hotplate is installed.
Installation of cooktop into the kitchen bench Installation procedure: Side clearances: If the distance measured from the periphery of the nearest burner to any vertical surface is less than 200 mm, the surface shall be protected in accordance with clauses 6.10.1.2 of AS/NZS 5601.1 1. For cutout dimensions and clearances refer Fig.1. 2. The clips and the adhesive seal (underside of the cooktop) are already fitted (depending on the model), do not under any circumstances remove them.
connected first and that all wires are connected to the correct terminals. Fig. 4. Gas During the planning stage, consider the position of supply connections. The cooktop must be connected to the gas supply with upstream connection of an isolation valve in accordance with the respectively valid regulations. We recommend that the isolation valve be fitted prior to the cooktop to enable isolation of cooktop from gas supply. The valve must be easily accessible at all times.
Ensure that the hose does not contact the hot surfaces of the hotplate, oven, dishwasher or any other appliance that may be installed underneath or next to the hotplate. The hose should not be subjected to abrasion, kinking or permanent deformation and should be able to be inspected along its entire length with the cooktop in the installed position. Unions compatible with the hose fittings must be used and all connections tested for gas leaks.
Request change-over injectors from our customer service deparment (refer injector chart below for sizes). Natural Gas Burner Hourly Gas Consumption (MJ) Universal LPG Injector mark Hourly Gas Consumption (MJ) Injector mark (mm) Auxiliary 3,60 90 3,50 50 Semi-rapid 6,50 118 6,00 67 Rapid 10,80 155 10,00 85 Triple flame 16,00 182 13,50 100 Before conversion the cooktop must be disconnected from the electricity and gas valves must be turned to the OFF position.
Adjustment of the taps Set the control knobs to minimum. Remove the control knobs from the taps. Fig. 9. It has a flexible rubber valve reinforcing ring. Simply press on this seal with the tip of a screwdriver to allow access to the tap adjusting screw. Fig. 9 Never remove the valve reinforcing ring. Adjust the minimum ring setting by turning the by-pass screw using a flat head screwdriver. To adjust the minimum flame for N.G.
- Use the disassembly lever 483196 availablle from our Technical Assistance Service. Remove the front clips by applying the lever to the zones indicated. Fig. 10a. Fig. 10a To assemble the grease splash tray again, proceed in the reverse order to removal. It is important that all the seals are refitted to form a seal. These devices are essential for the correct operation of the appliance as they prevent liquids and dirt from entering the appliance. Refit the control knobs. Never remove the tap spindle.
Operating instructions Burner locations 1 6 2 1 2 3 4 5 6 34 4 5 Pan supports Control knobs Auxiliary burner (up to 1 kW) Semi-rapid burner (up to 1,75 kW) Rapid burner (up to 3 kW) Triple-flame burner (up to 4 kW) The gas burners Operation There are indications to show which burner each control knob operates. Fig. 12. Fig. 12 It is essential to ensure that all the burner parts and pan supports are correctly installed for the appliance to work correctly. Fig.13-14. Fig.
While the control knob is still pressed down, sparks are produced on all burners. The flame ignites (it is no longer necessary to press down the control knob). 2. Turn the control knob to the required setting. If it does not come on, turn the control knob to the off setting and repeat the steps above. This time, press and hold the control knob for longer (up to 10 seconds). Warning! If after 15 seconds the flame does not ignite, switch off the burner and open a nearby window or door.
kitchen is well ventilated: either keep the natural ventilation apertures open, or install a ventilation system (extractor hood). If using the appliance intensively for prolonged periods, you may require additional ventilation (e.g. by opening a window) or more effective ventilation (e.g. by increasing the cooktop's ventilation, if possible). If the burner flames are accidentally blown out, switch off the burner operating control knob and do not try to relight it for at least one minute.
Additional coffee maker support Only for use on the auxiliary burner with pans which are no more than 12 cm in diameter. The manufacturer accepts no liability if these accessories are not used or are used incorrectly. Cooking recommendation Very high, high Medium Double or triple flame burner Boiling, grilling, browning and Asian food (wok). Reheating and keeping things hot: cooked and pre-cooked dishes. Rapid burner Steaks, omelettes, frying. Rice, white sauce and ragout.
Precautions for use The following advice is intended to help you save energy and prevent pan damage: Use pans which are the right size for each burner. Do not use small pans on large burners. The flame should not touch the sides of the pan. Do not use damaged pans, which do not sit evenly on the cooktop. Pans may tip over. Only use pans with a thick, flat base. Do not cook without using a lid and make sure the lid is properly fitted to avoid wasting energy.
Cleaning and maintenance Cleaning Once the appliance is cool, use a sponge to clean it with soap and water. After each use, clean the surface of the respective burner parts once they have cooled down. If any residue is left (baked-on food, drops of grease etc.), however little, it will become stuck to the surface and more difficult to remove later. The holes and grooves must be clean for the flame to ignite properly. The movement of some pans may leave metal residue on the pan supports.
Service DO NOT MODIFY THIS APPLIANCE. Only authorized personnel from the Service Centre are qualified to work on the appliance. Sometimes certain faults detected can be easily resolved. Before calling the Service Centre, bear in mind the following advice: Fault Possible cause Solution The general electrical system is malfunctioning. Defective fuse. Check the fuse in the main fuse box and change it if it is damaged.
Wiring diagram A. Switch B. Blue wire C. Brown wire D. Terminal E. Ignition module www.bosch-home.
