BOSCH INSTALLATION INSTRUCTION MANUAL for Bosch Electric Built-in Ceramic Cook-top Models NKT 72 and NKT 92 MANUEL D’INSTALLATION Surface de cuisson électrique en céramique encastrée Modèles NKT 72 et NKT 92 BEFORE YOU BEGIN, READ THESE INSTRUCTIONS tOMPLETELY AND CAREFULLY VEUILLEZ LIRE ATTENTIVEMENT CE MANUEL AVANT DE COMMENCER L’INSTALLATION. IMPORTANT: Save these instructions for the local electrical inspector’s use INSTALLER; Please leave this manual with owner for future reference.
Table of Contents Introduction 3 Tools You Will Need Power Requirements Counter Preparation Steps for Installation Technical Data 4 Preparing the Location Table des matières for 30” Cook-Top 5 for 36” Cook-Top 6 Attaching Fastening Rails 7 Placing the Cook-Top 8 Electrical Supply 9 Electrical Connections 10 Final Check List 11 Schematic Wiring Diagrams 12 Introduction 14 Les outils dont vous aurez besoin Spécifications électriques requises Préparation du comptoir Étapes de l’install
Introduction Please read these instructions COMPLETELY AND CAREFULLY, They will save you time and effort and help to ensure optimum cook-top performance. Be sure to observe all WARNINGS. These installation instructions are intended for use by a qualified installer. In addition to these instructions the cook-top shall be installed; • In the United States, in accordance with the National Electric Code/State and Municipal codes and/or local codes. • In Canada, in accordance with Canadian Electric Code C22.
Technical Data NKT 72 series, (30”, 4 element) Dimensions, NKT 72 a Height 4” 102 mm b Width 30” 762 mm c Depth 201/2” 521 mm Electrical Rating, NKT 72 Volts Hertz Amperes Watts 240 60 40 7 900 208 60 28 6 000 NKT 92 series, (36”, 5 element) Dimensions, NKT 92 .
Preparing the Location for 30”, four Element Cook-Top Work top: The work top must have a minimum ' Noté: 24” min. clearance if bottom of wood or metal cabinet is protected by not less thickness of 1’ ’. It must be level than ‘/4” flame retardant millborad and sealed along the wall to protect covered with not less than No. 28 MSG against spilled liquid. sheet steel, 0.015 ” stainless steel, or 0.024 ’ ’ aluminum or 0.020” copper. Cabinets: Cabinets must resist temperatures 30” min.
Preparing the Location for 36”, five Element Cook-Top Work top:, The work top must have a minimum Note: 24” min. clearance if bottom of wood or metal cabinet is protected by not less thickness of i ”. It must be level than >/4’ ’ flame retardant millborad and sealed along the wall to protect covered with not less than No. 28 MSG against spilled liquid. sheet steel, 0.015” stainless steel, or 0.024” aluminum or 0.020” copper. Cabinets: Cabinets must resist temperatures .30” min.
Attaching Fastening Rails used for both NKT 72 and NKT 92 series To attach the fastening rails: 1. Mark the center as shown in drawing. 2. Align rails using notch. 3. Secure the rails tightly using screws. Note: a. The top flange of rail must sit tightly against the counter top, b. If counter top is tiled, the lower screws holes in the rails should be used. Important: • Do all counter top preparation-before installing the cook-top. Be sure to clean area after cutting and before installing cook-top.
Placing the Cook-Top 1. Thread the cable through the cutout opening. 2. Gently place the cook-top into the cutout, taking care to assure that cable does not become pinched between the cook-top and the counter cutout, and press in place so that cook-top interlocks with rails. Note: If installing on a tiled counter top, seal the tile joints with silicone rubber. SPECIAL NOTE: Do not install the cooktop over a refrigerator, dishwasher or washing machine.
Electrical Supply Before installing the cook-top have a qualified WIRING REQUIREMENTS electrician verify that your home is provided with When making the wire connections, use the entire adequate electrical service and that the addition of length of the conduit provided (3 feet). The the cook-top will not overload the branch circuit conduit must not be cut. on which it is to be installed.
Electrical Connections This appliance is manufactured with a green and Cable from power supply yellow striped GROUND wire connected to the cook-top chassis. After making sure that the power has been turned off connect the flexible conduit from the cook-top to the junction box using a U.L. listed conduit connector, see figures A and B. Figures A and B and the instructions provided below present the most common way of connecting the cook-tops.
Final Check List To prevent improper connection leading to damage of electrical components and so voiding the warranty, the following steps must be performed: 1. Check the electrical requirements and make sure you have the correct electrical supply and that the cook-top is properly grounded. 2. Make sure all control knobs are in the off position. 3. Turn on the power supply to the cook-top. 4. Check power at junction box wires using a volt meter having a range of 0-250 VAC.
Schematic Wiring Diagrams NKT 72 series 12
