MIC-BP4 Bi-Phase Converter Card for the MIC400 PTZ Camera Series Bosch Security Systems EN Installation and Operation Manual
BP4 Bi-phase card | Installation and Operation Manual AAAEN| 2 MIC-BP4 Bi-Phase Converter Card For the MIC400 series camera Chapters 1. Introduction 2. MIC-BP4 Bi-phase Converter Card 3.
BP4 Bi-phase card | Installation and Operation Manual AAAEN| 3 Introduction............................................................... 1-6 MIC-BP4 Bi-Phase Converter Card…................................................. Versions.............................................................................................. Features.............................................................................................. Unpacking......................................................................
BP4 Bi-phase card | Installation and Operation Manual Safety Precautions The following symbols are used throughout this manual please pay careful attention to their meaning. The lightning flash with an arrowhead symbol within a triangle is intended to alert the user to the presence of non-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
BP4 Bi-phase card | Installation and Operation Manual This product complies with the following EC directives:EMC Directive (89/336/EC as amended) Machinery Directive (98/37/EC) LV Directive (73/23/EC) RoHS (Restriction of Hazardous substances) 2002/95/EC WEEE (Waste Electrical & Electronic Equipment) 2002/96/EC This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and ele
BP4 Bi-phase card | Installation and Operation Manual Intentionally Blank AAAEN| 6 CHAPTER 1 Introduction The MIC-BP4 Bi-phase converter card allows translation of the Bosch Bi-phase protocol signals to RS485, half duplex telemetry signals. This enables Bosch Security Systems MIC400 series PTZ cameras to interface with Bosch Bi-phase equipment. The MIC-BP4 Bi-phase converter card also enables the camera address to be set through its integrated DIP switch selector.
BP4 Bi-phase card | Installation and Operation Manual AAAEN| 7 Versions MIC-24PSU - 1 expansion slot; BP3 or BP4 This manual covers the installation and operation of Bosch Security Systems MIC-BP4 Bi-phase converter card can be fitted in MIC400 power supplies which have a free expansion slot (header CN2). MIC-115PSU - 1 expansion slot; BP3 or BP4 MIC-THERMAL-PSU - 1 expansion slot; BP3 or BP4 For MIC400IR cameras please refer to the MIC-BP3 Bi-phase converter card manual.
BP4 Bi-phase card | Installation and Operation Manual CHAPTER 2 MIC-BP4 Bi-phase Converter Card Picture 1 – The MIC-BP4 Bi-phase converter card for MIC400 series power supplies. AAAEN| 8 Bi-phase Telemetry Specifications Shielded 2-wire, half-duplex, multi-drop, 5000 ft. cable limit, 18AWG gauge needed for 500ft distance. Bi-phase is the standard Bosch protocol used to send Pan/Tilt/Zoom control over 2-wire shielded twisted pair (STP) terminated with an 110Ω terminal resistor.
BP4 Bi-phase card | Installation and Operation Manual CAUTION: The shield must be connected to the controller end only The MIC-BP4 has a 110 Ω termination resistor between the Bi-phase +ve and –ve terminals which should be removed unless the camera is the last in the daisy chain of cameras. Typical Wiring Example In a daisy chain configuration (as shown in Figure 2 below), a termination resistor of 110 Ω must be added to the last MIC400 in the series.
BP4 Bi-phase card | Installation and Operation Manual CAUTION: The shield must be connected to the controller end only Figure 3 – Layout of a MIC400 Non-IR Power Supply PCB (MIC-240PSU, MIC-012PSU, MIC-024PSU & MIC-115PSU) AAAEN| 10 Setting the MIC400 Address (in Hardware) The MIC-BP4 Bi-phase converter card supports changing the address of the MIC400 at the pole base through hardware.
BP4 Bi-phase card | Installation and Operation Manual 1 to 127 DIP Switch Address Settings for MIC400 series cameras Bosch Security Systems Issue 1 AAAEN| 11 128 to 255 DIP Switch Address Settings for MIC400 series cameras
BP4 Bi-phase card | Installation and Operation Manual CHAPTER 3 Technical Specifications Physical Dimensions and Cable Specification MIC-BP4 card dimensions 60 mm (W) x 10mm (H) x 70mm (D) Recommended cable type Cable Type Distance Transmission Rate STP - Shielded Twisted Pair 1524 m (5000 ft) Belden 8760 recommended 31.25 KHz Gage Termination 1.
