IntuiKey Keyboard Keyboard Version 1.
IntuiKey Keyboard Table of Contents | en iii Table of Contents 1 Introduction to the IntuiKey Keyboard Series 1 1.1 Operating the IntuiKey Keyboard 1 1.2 The Status Display 2 1.3 The Keypad 3 1.4 The Softkeys and the Softkey Display 3 1.5 The Joystick 4 1.6 Navigating the System with the IntuiKey Keyboard 4 1.6.1 General Guidelines for Navigating the IntuiKey Menus 4 1.6.2 The Product Selection Menu 4 1.6.3 Selecting a Device for Control 5 1.6.
iv en | Table of Contents F.01U.127.291 | 1.93 | 2009.03 IntuiKey Keyboard User Manual Bosch Security Systems, Inc.
IntuiKey Keyboard 1 Introduction to the IntuiKey Keyboard Series | en 1 Introduction to the IntuiKey Keyboard Series This manual contains all the information necessary to operate the IntuiKey Keyboard. Step-bystep procedures, illustrations, and sample menus guide you through each phase of IntuiKey operation. Throughout the manual, you will see sample drawings of each menu as they appear on the keyboard. These drawings display the softkey text in relation to the Softkey.
2 1.2 en | Introduction to the IntuiKey Keyboard Series IntuiKey Keyboard The Status Display The Status Display changes dynamically to display pertinent information about the keyboard’s present mode of operation. Typically, its information conveys one of two keyboard operating modes: Normal Mode or Error Code. In Normal Mode, the status display provides data pertaining to the present device under control (e.g. monitor number, camera number, device under control status, etc.).
IntuiKey Keyboard 1.3 Introduction to the IntuiKey Keyboard Series | en 3 The Keypad The Keypad includes the five function buttons (located directly below the status display), as well as the numeric keypad. PROD displays the keyboard’s Product Selection menu. This function key (in conjunction with the Softkeys/Softkey Display) selects the device under the control of the keyboard. The Product Selection menu also provides access to the Keyboard Control menu.
4 en | Introduction to the IntuiKey Keyboard Series 1.5 IntuiKey Keyboard The Joystick The IntuiKey Joystick provides three levels of system functionality: control of pan/tilt/zoom for an external camera, navigating the on-screen programming menus of the Allegiant Video Switchers, AutoDome® Series Cameras and other devices, and playback control when operating DVR devices. Use of the joystick to control playback of DVR devices is covered later in this manual.
IntuiKey Keyboard Introduction to the IntuiKey Keyboard Series | en 5 NOTICE! When the IntuiKey is first connected up to a device, or whenever a new video device i is added to an existing system, enter the Product Selection menu and press the PROD key. The keyboard will initiate a scan of the communication lines and update the list of devices connected to it. If communication is ever lost with an existing device, the product name display will indicate an Off_Line condition.
6 en | Introduction to the IntuiKey Keyboard Series 1.7 IntuiKey Keyboard Alarm/Alert/Action Indication When the IntuiKey detects that an alarm/alert/action condition has occurred on the presently controlled device, the key flashes red and an audible tone is heard. During alarm responses, Divar DVRs and System4 multiplexers will also show special icons to represent the different types of alarm conditions.
IntuiKey Keyboard 2 Controlling Allegiant Series Video Switchers | en 7 Controlling Allegiant Series Video Switchers Before you can take control of an Allegiant Video Switcher, you may have to perform a log-on procedure to gain access to the Allegiant Main Control menu to control the switcher. Note: This chapter applies to the KBD-Universal Model only. – The keyboard generates a short, audible “beep” when first entering the Allegiant log-in screen.
8 2.1 en | Controlling Allegiant Series Video Switchers IntuiKey Keyboard The Allegiant Main Control Menu To access the Allegiant Main Control menu: 1. Press PROD to put the keyboard in Product Selection Mode. The keyboard displays the the Product Selection menu in the softkey display. 2. 3. Press the Allegiant softkey button. The status display shows the Allegiant mode. To select a camera, enter a valid 1 to 4 digit camera number using the numeric keypad and press ENTER.
IntuiKey Keyboard Controlling Allegiant Series Video Switchers | en Exit Exits one menu and reverts to the main menu for the particular Device Lockout function being programmed/controlled. Accesses a softkey menu, allowing the locking/unlocking of 9 specified cameras and monitors. Exit Monitor Lock Monitor Unlock Remote Lock Remote Unlock Figure 2.4 Device Lockout Menu – Monitor Lock/Unlock – If the monitor to be locked/unlocked is not the present monitor, press MON on the keypad.
10 en | Controlling Allegiant Series Video Switchers Alarm Control IntuiKey Keyboard Alarm commands control the system’s automatic video switching capabilities in response to alarm signals activated in the Allegiant system. The camera activated by an alarm is normally the same as the alarm number, but this relationship can be changed using the optional LTC 8059/00 Master Control Software for Windows® or the optional LTC 8850/00 Graphical User Interface software package.
IntuiKey Keyboard Controlling Allegiant Series Video Switchers | en 11 Program Sequence Changes the softkey display and requests entry of a sequence number to program. The status display shows the following: --- Alarm# Allegiant Figure 2.
12 en | Controlling Allegiant Series Video Switchers Load Sequence IntuiKey Keyboard Enables the loading of a previously programmed sequence. – Press the Load Sequence softkey. The status display shows the following: --- Sequence? Allegiant Figure 2.8 Load Sequence Display Sequence programming is displayed on the controlled monitor screen. – Enter the sequence number, then press ENTER. – To unload a sequence, stop the sequence (if necessary), press the Load Sequence softkey, then press ENTER.
IntuiKey Keyboard Controlling Allegiant Series Video Switchers | en Command Script 13 Accesses a series of menus, allowing execution of Allegiant script commands. Refer to the Allegiant Instruction Manual for additional information. – Run Command Script This function allows the user to execute *STAR commands from the keyboard. The Allegiant supports over 150,000 commands. Press the Command Script softkey to display the following softkey menu: Exit Run Script *Star Figure 2.
14 en | Controlling Allegiant Series Video Switchers Camera Control IntuiKey Keyboard Displays the camera control softkey menu, allowing the entry of various camera control commands. Refer to Appendix B at the back of this manual for details on the camera commands. Access to certain AutoDome menus and commands may be prohibited by security features within the camera. Refer to Appendix C for more User Functions information.
IntuiKey Keyboard 2.
16 en | Controlling Allegiant Series Video Switchers IntuiKey Keyboard Menu Softkey Function Description Menu 20 CPU Temp Menu 20 4-6 Digit Camera ID Menu 21 Adjust Display Position Allegiant User Function # Access Level 45 Any 47 12 4 1-71 Menu 21 Brightness/Status Selection 5 1-71 Menu 21 Display Options 6 1-71 Menu 21 Set Time 7 1-71 Menu 21 Set Date 8 1-71 Menu 21 All Display Position 24 1-71 Menu 21 All Display Brightness/Status 25 1-71 Menu 21 All Display Option 26 1-7
IntuiKey Keyboard 2.4 Error Error 01 Controlling Allegiant Series Video Switchers | en 17 Allegiant Error Messages Name Invalid Camera Request Description The camera number entered from the keyboard does not exist. If using the optional LTC 8059/00 Master Control Software or the LTC 8850/00 Graphical User Interface Software, ensure that the number exists in the Camera Identification table. Download the table to be Error 02 Error 03 Invalid Monitor Request Remote Device Locked by User# sure.
18 en | Controlling Allegiant Series Video Switchers IntuiKey Keyboard Error Error 53 Name Switcher Empty Description The user has attempted to control a sequence using the NEXT, Error 55 SEQUENCE Priority PREV, RUN, or HOLD keys, without there being a sequence loaded. The switcher sequence being requested or cleared requires monitors that are in use by a user of equal or higher priority.
IntuiKey Keyboard 3 Controlling Divar Series Digital Video Recorders | en 19 Controlling Divar Series Digital Video Recorders This section applies to the KBD-Universal and KBD-Digital models. NOTE: Depending on the model of the Divar, some features described below may not be supported. See the table below for supported software features by Divar model.
20 en | Controlling Divar Series Digital Video Recorders IntuiKey Keyboard Software Features 3.1 Divar Divar Easy Divar MR Divar XF – Up Y Y Y Y – Left Y Y Y Y – Down Y Y Y Y – F1 Y Y N N – Escape Y Y Y Y – Help Y Y N Y – Right Y Y Y Y – Down Y Y Y Y – F2 Y Y N N – Select Y Y Y Y User Level Y Y Y Y Help Y Y N Y Protect Y N N N Select DVR Y N N Y DVR (Keyboard) Audio Y Y Y Y Accessing the Divar Main Control Menu 1.
IntuiKey Keyboard i Controlling Divar Series Digital Video Recorders | en 21 NOTICE! Keyboard access to MONB must be enabled within the Divar menus. See the Divar manual for details. – Indicates that the DVR is in an ACTION alarm mode. – Indicates that the DVR is in a contact activated alarm mode. – REC – Indicates that the DVR is currently recording. – PLAY – Indicates that the DVR is in a replay mode. – ZOOM – Indicates that the DVR is displaying a zoomed image.
22 en | Controlling Divar Series Digital Video Recorders – IntuiKey Keyboard Quad Screen Divides the screen into four separate areas. Enable Quad Screen Mode by pressing the Quad Screen key once. Pressing the key additional times cycles through available viewing configurations. – Multi Screen Enables multiscreen displays. The capabilities and user setup of the DVR model under control determine the available configurations.
IntuiKey Keyboard Controlling Divar Series Digital Video Recorders | en – 23 Play Activates DVR playback mode and displays the PLAY indicator in the IntuiKey status display. Press the softkey again to cancel the playback mode. While in the Playback mode, the joystick functions as follows: a. Move joystick forward or rotate the joystick knob in the clockwise direction to put the DVR into forward playback mode. The further the joystick is moved or rotated, the faster the playback will occur. b. c.
24 en | Controlling Divar Series Digital Video Recorders 3.2.2 IntuiKey Keyboard DVR On-screen Menu Controls This softkey menu provides various controls for navigating DVR on-screen menus. Detailed command descriptions follow. Exit Help ^ Up ^ Up < Left Right > v Down v Down F1 F2 Escape Figure 3.4 Select Divar DVR Menu Control Softkey Description Exit Exits the present menu, Softkey Description Help Accesses the DVR’s on-screen HELP menu. reverting to the previous ^ Up menu.
IntuiKey Keyboard 3.2.3 Controlling Divar Series Digital Video Recorders | en 25 DVR Control Menu This softkey menu provides controls for selecting devices and protecting recordings. It also provides access to the on-screen Help menu and the softscreen menu for accessing and navigating the DVR’s on-screen configuration menu. Exit Menu Help Protect Select DVR User Level Figure 3.5 – Divar Audio Divar DVR Control Menu Exit Exits the present menu, reverting to the previous menu.
26 en | Controlling Divar Series Digital Video Recorders – IntuiKey Keyboard Protect It is possible to mark a video recording so it cannot be overwritten. a. During playback, press the Protect key to mark the beginning of a protected recording. Playback will pause and a dialog window will appear, showing the time and date of this selection. b. Press the Select key to continue playing the video that you wish to protect. The c.
IntuiKey Keyboard 4 Controlling System4 Video Multiplexers | en 27 Controlling System4 Video Multiplexers This section applies to KBD-Universal and KBD-Digital Models. 4.1 Accessing the MUX Main Control Menu 1. Press PROD to put the keyboard in the Product Selection Mode. The softkey display shows the Product Selection menu. Depending on the number of devices that are connected to the IntuiKey, the list may show up to 32 total devices spanning 3 menu screens. 2.
28 en | Controlling System4 Video Multiplexers IntuiKey Keyboard 4.2 Programming/Controlling MUX Functions 4.2.1 Password Entry If a password is required by the multiplexer on-screen display, you must press ENTER after each number entered for the password (e.g. if the password is 1-2-3-4, you then press 1, then ENTER, 2, then ENTER, etc.). Exit Play Quad Screen ZOOM Multi Screen Select Cameo Segment Freeze Recorder Controls Sequence Camera Control Toggle VCR Text Mode MUX Control Figure 4.
IntuiKey Keyboard Controlling System4 Video Multiplexers | en 29 Select Cameo Segment When in Multi or Quad Mode, the screen area where a camera is displayed is called a cameo. Press the Cameo softkey to enter the cameo selection mode. In this mode, joystick is used to select which cameo window will be under control of the keyboard. Entering a number into the keyboard while in this mode will cause the camera to appear in the currently selected cameo window.
30 en | Controlling System4 Video Multiplexers IntuiKey Keyboard Recorder Controls Accesses the DVR1/VCR Control softkey menu, allowing selections for control of either a DVR1 Series digital recorder or a conventional VCR. Additional menus are displayed for control of the selected device. DVR1 Controls Exit VCR Controls Figure 4.4 Recorder Control Menu Camera Control Displays the Camera Control softkey menu, allowing entry of various camera control commands.
IntuiKey Keyboard Controlling System4 Video Multiplexers | en 31 Softkey Description Exit Exits the present menu, reverting to the previous menu. On-screen Menu Provides access to the multiplexer’s on-screen display (OSD), if the access level has been enabled to FULL ACCESS (otherwise, the softkey display indicates that the present user level is not high enough for this level of access).
32 en | Controlling System4 Video Multiplexers Softkey Select MUX IntuiKey Keyboard Description Pressing this softkey displays a short message on the softkey display indicating that entry of a multiplexer address is required. The IntuiKey status display changes to the Address Multiplexer screen. Upon entering an Allplex number, press ENTER. The keyboard determines whether the selected multiplexer is present.
IntuiKey Keyboard | en A 33 IntuiKey Menu Reference Product Table 1 ALLEGIANT MAIN Allegiant DVR MUX Keyboard Diagnostics 8 MUX Main 2 Terminal Mode Terminal Keyboard Control Exi t Factory Reset Exit Firmware Upgrade (User Protocol RS-485 Language Select Allegiant Baud 9600 Keyboard Test Contrast Adjust LCD Test Defined Text) Play Quad Screen ZOOM Multi Screen Freeze Select Cameo Segment Key Click On/Off Joystick Auto Cal.
34 en | IntuiKey Keyboard PRODUCT TABLE Allegiant Main 15 Exit Device Lockout Program Sequence Alarm Control User Log Off Main Scripts 80 Command Script Camera Control Exit User Functions Run Script Load Sequence Hold Sequence
IntuiKey Keyboard 32 Camera Pan/Tilt Commands Exit | en Camera Control Main 30 Exit Scan Auto-Pan Auto-pan Left Limit Auto-pan Right Limit Set Auto-pan Speed Pan Autospeed AutoPivot Enable Pivot Call-up Zone Masking Inactive Home Return Set Shot Modify Pre-set Tour Add Scene to Tour Aux On 33 Camera Functions Advanced Menu Show Shot Pre-set Scene Control Remove Scene from Tour 36 Exit Iris Control Auto Iris ALC Adjust Auto Iris Level Adjust Auto Iris Enable Iris Polarity 35 Camera Len
36 en | F.01U.127.291 | 1.93 | 2009.03 IntuiKey Keyboard User Manual Bosch Security System, Inc.
IntuiKey Keyboard B | en 37 Camera Control Command Reference The IntuiKey Keyboard provides access to the camera control functions for applicable system devices. Certain features may be restricted by the AutoDome security feature. Refer to Appendix D for additional details. The Camera Control Main menu is shown below. The command descriptions follow. Camera Functions Exit Advanced Menu Set Shot Show Shot Modify Pre-set Tour Add Scene to Tour Aux On Figure B.
38 en | IntuiKey Keyboard – Add Scene to Tour This softkey adds a shot to the camera’s tour. Pressing the softkey changes the status display to the following. ---- Add Scene Allegiant Figure B.3 – Not Used – Aux On Allegiant Add Scene Status Display Press this softkey to enter a number associated with an auxiliary command. The status display changes to an entry box. i NOTICE! If ENTER is held down, the Aux command auto-repeats until the key is released.
IntuiKey Keyboard | en – 39 Show Shot Press Keypad Shot, and the status display changes for input as shown in Figure B.5. ---- Show Shot Allegiant Figure B.5 Allegiant Show Shot Status Display Entering a two digit shot number followed by ENTER selects a previously programmed camera position for the currently controlled camera. i NOTICE! This function is also accomplished by pressing the SHOT button (located next to the joystick) and holding it down for more than 1 second.
40 en | F.01U.127.291 | 1.93 | 2009.03 IntuiKey Keyboard User Manual Bosch Security System, Inc.
IntuiKey Keyboard C | en 41 Keyboard Camera Commands Function Auxiliary Number Preposition G3 Series Number G3 Series Allegiant G4 200 G4 300 G4 500 AutoDome Day/Night Receiver/ Series Series Series Driver AutoDome AutoDome AutoDome Camera Control Set Shot, 1 to 64 Show Shot, 1 to 64 Set Shot, 1 to 99 Show Shot, 1 to 99 Global enable/disable preposition Preset Scene Control Edit Tour 2, Custom Edit Tour 1, Standard Add Scene to Tour, 1 to 64 Remove Scene from Tour, 1 to 64 Add Scene to
42 en | Function IntuiKey Keyboard Auxiliary Preposition G3 Series G3 Series Allegiant G4 200 G4 300 G4 500 AutoDome Day/Night Receiver/ Series Series Series Number Number on/off 6 - - - Y - - - on/off 3 Y Y Y Y Y Y Y Y Y Y Y Y - Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y - Y Y Y Y Y Y Y Y Y Y Y - - Y Y Y Y Y Y Y Y Y Y - Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y - Y Y Y Y Y Y Y Y - Y Y Y Y Y Y Y Y Y Y Y Y - Y Note 1 Y Y Y - Y Y Y Y Y Y Y Y Y Y
IntuiKey Keyboard | en Function Auxiliary Preposition G3 Series Allegiant G4 200 G4 300 G4 500 AutoDome Day/Night Receiver/ Series Series Series Number Number Alarm Acknowledge on/off 65 - Note 3 Physical Output 1 on/off 81 - Physical Output 2 on/off 82 Physical Output 3 on/off 83 Physical Output 4 on/off 84 - - G3 Series 43 Driver - - AutoDome AutoDome AutoDome - Y Y Y Y Y Y Y Y Y Y Notes: 1.
44 en | F.01U.127.291 | 1.93 | 2009.03 IntuiKey Keyboard User Manual Bosch Security System, Inc.
Americas Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, Pennsylvania 17601 USA Telephone +1 888-289-0096 Fax +1 585-223-9180 Email: security.sales@us.bosch.com www.boschsecurity.us Europe, Middle East, Africa: Bosch Security Systems B.V. P.O. Box 80002 5600 JB Eindhoven, The Netherlands Phone: + 31 40 2577 284 Fax: +31 40 2577 330 emea.securitysystems@bosch.com www.boschsecurity.
