Specifications

Note:
3 Wire ConneXion:
The FourWire ConneXion ispreferred,butwherelocalcodesand
ordinancespermitgroundingthroughneutraland/orconversiontofourwire
isimpractical,unitmaybeconnectedto thebowersupplyviaathreewire
oonnedJon,
!. Disconnectelectricalpoweratthebreakerbox.
2. Removethe terminalblockcoverto exposethe terminalblock
(SeeFigureA).
3. Removethe top nut, starwasher,and roundwasherfrom each
post.
Note: DO NOTremovelastroundwasher,lastnut or internalwire
leads.
4. Placeoneterminallug (packagedwith this manual)on each
post. Replacethe starwasherand roundwasher andsecure
with 20 inch poundsof torque.
5. Strip3/8 inchesof insulationfrom the endof eachwire (See
FigureB).
6. insert strippedend of white wire into the centerlug ontop of
the groundstrap.Securethe clampingscrew(SeeFigureC).
7. Insert strippedend of redwire into the left lug. Secure
damping screw.
8. Insert strippedend of blackwire into the right lug. Secure
damping screw.
9. Tighteneachclampingscrewwith the appropriatetorque (See
Table! at right).
!0. Properlysecureflexibleconduitat knockoutpanelon range
andat supplysidejunction box.The wiring is now complete
(SeeFigureD).
4 Wire Cor_nection: (Preferred to three wire connection)
!. Disconnectelectricalpoweratthebreakerbox.
2. Removethe terminalblockcoverto exposethe terminalblock.
3. Removethe top nut, starwasher,and roundwasher
from each post.
Note: DO NOTremovelastroundwasher,lastnut or internalwire
leads.
4. Removescrewfrom bottomend of groundstrap.
5. Removeground strapfrom centerpost. Discard.
6. Attachoneterminallug (packagedwith this manual)
through holebelowterminalblockwith groundscrew.
7. Placeoneterminallug (packagedwith this manual)on
eachpost. Replacethe starwasherand roundwasherand
securewith 20 inch poundsof torque.
8. Strip3/8 inchesof insulationfrom the endof the wire (See
FigureC).
9. Inserttheinsulatedgroundingwireintothelugbelowtheterminal
block.
!0. Insertstrippedendof whitewireintothecenterlug.Securethe
clampingscrew.
!1. Insertstrippedendofredwireintothelef_lug.Secure
clampingscrew(SeeFigureD).
!2. Insert blackwireintotherightlug.Securedampingscrew.
!3. Tighteneachdamping screwwith the appropriatetorque (see
Table! at right).
!4. Properlysecureflexibleconduitat knockouton angleand at
supplysidejunctionbox.The wiring is now complete(See
FigureE).
Note-" DO NOT plug in range at this time.
Proceed to steps 8 and 9.
Step 7: Connect Flectric - He×ibLe Conduit With Wires ,,. Our Inspiration
Bosch recommends the range cord installation (previous page),
\ "x
Figure B - Stripped wire
Figure. C - Lug, wire and damping screw
Clamping Bcrew
Green Ground
Screw Red White Black
Figure D - Completed 3 wire connection
Figure E - Completed 4 wire connection
Table ! - Appropriate Torque levels
for Aluminum or
6
8
35
25
English ,, 5