BOSCH INSTALLATION INSTRUCTION' MANUAL for Bosch Electric Built-in Single & Double Oven Models HBN 64.J65,.166., BEFORE YOU BEGIN, READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY IMPORTANT: Save these instructions for _e local electrical inspector's nse'_ INSTALLER: Please leave this manual w_th owner for future reference.
Table of Contents INTRODUCTION ............................................................................................................................. Tools You Will Need ................................................................................................................... 3 Power 3 Requirements Choosing ............. Oven Location Steps for Installation TECHNICAL ......... .......................................................................................................
INTRODUCTION Please read these instructions COMPLETELY AND CAREFULLY. They will save you time .and effort and help to ensure optimum oven performmace. Be sure to observe all WARNINGS. These installation instructions are • use by a qualified installer. In addition structions the oven shall be installed: int_ndad for to these in- • In the United States, in accordance with the National Electric Code/State and Municipal codes and/or local codes.
TECHNICAL SINGLE DATA OVEN For cutout dimensions Preparing see following sections titled: Location Single Oven Models Electrical Ratings and Maximum Connected Load Convection Oven Hertz Amperes @240V/208V Watts @240V/208V HBN 642A UC 240/208 60 13.1/13.3 3,150/2,775 Yes HBN 645A UC 240/208 60 13.1/13.3 3,150/2,775 Yes HBN 646A UC 2401208 60 13.1/13.
UNDERCOUNTER -- INSTALLATION, SINGLE m L I O_n elec_l_ supply: LocateJun_onboxIn _lJa_mt cabinetor below bottomsupportsurface. I I I ! I I _" I openingwidth '1 I Bottom supper sud_,e must be solid, le_i_ and able to supper at least of 150 Ibs. \ I I I 114"min. distance b_'ween ovln door frme md -,,'jas*nt _ doom or dmw_ fron'= F-toe spa_ anm 2e.._" ._flh of oven do_- frame maintain minimum spadng u ahown.
WALL INSTALLATION, SINGLE OVEN Secureoven to cabinet uSklgthe screws movlded. Screws should be Inserted .= Ihrough the mountln_ holes In _e posi_ora _ldicat_d in me frame (o_m ! doorto see flame and mounlJngho_esI. Donot ov_tighten screws. Nnte: Do not slide oven across floor. Damage to floor covering or floor could result. . The oven support surface must be a minimum 3/4" thick plywood platform, solid, level and flush with the bottom of the cabinet cutout. . .
WALL INSTALLATION, DOUBLE OVEN Secure oven to cabinet using the screws provided. Screws should be inserted through the mounting holes in the positions indicated in the frame (open door to see frame and mounting holes). Do not overtightan screws, Note: Do not slide oven across floor. Damage to floor covering or floor could result. . The oven support surface must be a minimum 3/4" thick plywood platform, solid, level and flush with the bottom of the cabinet cutout. 3.
ELECTRICAL SUPPLY Before installing the oven have a qualified electrician verify that your home is provided with adequate electrical service and that the addition of the oven will not overload the branch circuit on which it is to be installed. A separate three-wire or four-wire single phase, 240 Volt, 60 Hz., or a 208 Volt, 60 Hz. branch circuit is required. Note: For use with 208 V, 60 Hz supply voltage the wiring must be modified as shown in Connecting to 208 Volt Circuit.
CONNECTING To connect to 208 volt circuit: TO 208 V CIRCUIT The ovens are pre-wired for connection to 240 volt, 60 Hertz supply. If connecting to a 208 volt, 60 Hz. supply a jumper must be used across, two terminals. For the double oven models ther'e are two jumpers, one for the upper oven and one for the lower oven. For the single ovens there is one jumper. Please refer to figures below for placement jumper for 208 volt, 60 hertz connection. 1 .
ELECTRICAL CONNECTIONS 3-WIRE This appliances is manufactured with a green GROUND wire connected to the oven chassis. After making sure that the power has been turned off connect the flexible conduit from the oven to the junction box using a U.L. listed conduit connector. Figures A and B and the instructions provided below present the most common way of connecting the ovens. Your local codes and ordinances, of course, take precedence to these instructions.
FINAL CHECK LIST you have modified the oven(s) for use on 208 volt the voltage reading between the black and red wires should be 190 to 208 volts. To prevent improper connections leading to damage of electrical components and so voiding the warranty, the following steps must be performed: Set the time of day by pressing the Set Clock button and pressing the plus (+) or minus (-) button, to the right of the display to set the correct time.
