Operation Manual

10
Setting the timer
You can use the timer as a kitchen timer. It runs independently
of the oven. The timer has a special signal. This means that you
can tell whether the timer duration or the cooking time has
elapsed. You can also set the timer if the childproof lock is
active.
Setting procedure
1. Press the S Timer button.
The
S symbol flashes.
2. Use the - or + button to change the timer duration.
Default value for + button = 10 minutes
Default value for - button = 5 minutes
The timer starts after a few seconds. The
S symbol lights up in
the display. You will see the time counting down.
When the time has elapsed
A signal sounds. Press the
S Timer button. The timer goes out.
Changing the timer duration
Press the
S Timer button. Use the + or - button to change the
time.
Cancelling the setting
Press the
S Timer button. Press the - button until zero is shown
on the display.
The timer and cooking time count down at the same time
Both symbols light up. You can see the timer duration counting
down in the display.
To call up the
x remaining cooking time, y end time or 0
clock:
Press the
0 Clock button repeatedly until the relevant symbol
appears.
The value you are checking appears for several seconds on the
display.
Childproof lock
Oven
The oven has a childproof lock to prevent children switching it
on accidentally.
Switching the childproof lock on and off
The function selector must be switched off.
To switch on: press and hold the
C key button until the C
symbol appears in the display. This takes about 4 seconds.
To switch off: press and hold the
C key button until the C
symbol goes out.
Notes
■ You can set the timer and clock at any time.
■ If the childproof lock is active, it will be cancelled following a
power cut.
Care and cleaning
With good care and cleaning, your oven will remain clean and
fully-functioning for a long time to come. Here we will explain
how to maintain and clean your oven correctly.
Notes
■ Slight differences in the colours on the front of the oven are
caused by the use of different materials, such as glass,
plastic and metal.
■ Shadows on the door panel which look like streaks, are
caused by reflections made by the oven light.
■ Enamel is baked on at very high temperatures. This can
cause some slight colour variations. This is normal and does
not affect their function. The edges of thin trays cannot be
completely enamelled. As a result, these edges can be
rough. This will not impair the anti-corrosion protection.
Cleaning agents
Damage to the various different surfaces caused by using the
wrong cleaning agent can be avoided by observing the
following instructions.
When cleaning the oven do not use
■ sharp or abrasive cleaning agents,
■ cleaning agent with a high alcohol content,
■ scouring pads,
■ high-pressure cleaners or steam jets.
■ Do not clean individual parts in the dishwasher.
Wash new sponges thoroughly before first use.
The control
panel
Hot soapy water:
Clean with a dish cloth and dry with a soft
cloth. Do not use glass cleaners or glass
scrapers for cleaning.
Stainless-steel
surfaces
Clean with warm soapy water and a soft cloth.
On stainless-steel surfaces, always wipe par-
allel to the natural grain. Otherwise, you may
scratch the surface. Dry with a soft cloth.
Remove flecks of limescale, grease, starch
and albumin (e.g. egg white) immediately. Do
not use any abrasive materials, scouring
sponges or rough cleaning cloths. The stain-
less-steel fronts can be polished using a spe-
cial care product. Follow the manufacturer's
instructions. You can purchase special stain-
less-steel cleaner from our after-sales service
or from specialist retailers.
Enamel sur-
faces and lac-
quered
surfaces
Wipe with a damp cloth and some washing-up
liquid. Dry with a soft cloth.
Rotary knobs Wipe with a damp cloth and some washing-up
liquid. Dry with a soft cloth.
Glass panel Clean using glass cleaner. Do not use any
abrasive cleaning agents or sharp metal
objects. These could scratch and damage the
surface of the glass panel.
Seal Wipe with a damp cloth. Dry with a soft cloth.