User Manual

English | 19
Bosch Power Tools 1 609 92A 2C8 | (29.9.16)
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise levels of the product are:
Sound pressure level 93 dB(A); Sound power level
104 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
h
(triax vector sum) and uncertainty K
determined according to EN 60745-2-3:
Surface grinding: a
h
=7.5m/s
2
, K=1.5m/s
2
,
Disk sanding: a
h
=4.5m/s
2
, K=1.5m/s
2
.
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Technical Data
Angle Grinder GWS ... 22-180
H
22-180
JH
22-230
H
22-230
JH
Article number 3 601 ... H81 L.. H81 M.. H82 L.. H82 M..
Rated power input
W22002200 2200 2200
Output power
W15001500 1500 1500
Rated speed
min
-1
8500 8500 6500 6500
Grinding disc diameter, max.
mm 180 180 230 230
Thread of grinder spindle
M 14 M 14 M 14 M 14
Thread length (max.) of grinder spindle
mm 25 25 25 25
Restarting Protection
–  – 
Reduced starting current
–  – 
Weight according to EPTA-Procedure 01:2014
– with vibration-damping auxiliary handle
– with standard-auxiliary handle
kg
kg
5.1
5.0
5.1
5.0
5.3
5.2
5.3
5.2
Protection class /II /II /II /II
Angle Grinder GWS ... 24-180
JH
24-230
H
24-230
JH
26-180
JH
26-230
JH
Article number
3 601 ... H83 M.. H84 L.. H84 M.. H55 M.. H56 M..
Rated power input
W24002400 2400 2600 2600
Output power
W16001600 1600 1700 1700
Rated speed
min
-1
8500 6500 6500 8500 6500
Grinding disc diameter, max.
mm 180 230 230 180 230
Thread of grinder spindle
M 14 M 14 M 14 M 14 M 14
Thread length (max.) of grinder spindle
mm 25 25 25 25 25
Restarting Protection
 –  
Reduced starting current
 –  
Weight according to EPTA-Procedure 01:2014
– with vibration-damping auxiliary handle
– with standard-auxiliary handle
kg
kg
5.1
5.0
5.2
5.1
5.3
5.2
6.0
5.9
6.1
6.0
Protection class
/II /II /II /II /II
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Only for power tools without reduced starting current: Starting cycles generate brief voltage drops. Interference with other equipment/machines may
occur in case of unfavourable mains system conditions. Malfunctions are not to be expected for system impedances below 0.25 ohm.
OBJ_BUCH-777-010.book Page 19 Thursday, September 29, 2016 3:35 PM