Technical data
Table Of Contents
- Table of contents
- 1 Key to symbols and safety instructions
- 1.1 Explanation of symbols
- 1.2 Safety instructions
- 2 About the appliance
- 2.1 Designated use
- 2.2 EU Declaration of Conformity
- 2.3 Data plate
- 2.4 Standard delivery
- 2.5 Accessories
- 2.6 Tools, materials and miscellaneous parts
- 2.7 General information on energy use and heat production
- 2.8 Function description of the hybrid manager
- 2.9 Handling circuit boards
- 2.10 Refrigerant circuit
- 2.11 Combi boiler with serial buffer tank, bypass valve and unmixed heating circuit
- 2.12 System boiler with serial buffer tank, bypass valve and unmixed heating circuit
- 2.13 Combi boiler with serial buffer tank, bypass valve, unmixed heating circuit and independently controlled mixed heating circuit
- 2.14 System boiler with serial buffer tank, bypass valve, unmixed heating circuit and independently controlled mixed heating circuit
- 2.15 Overview of components
- 2.16 Dimensions
- 2.17 Technical Data
- 3 Regulations
- 4 Transport
- 5 Mounting and installation
- 5.1 Preparing for installation
- 5.2 System component configuration
- 5.3 Pre-installing pipes
- 5.4 Mounting the hybrid manager
- 5.5 Installing the external unit
- 5.6 Installing the refrigerant circuit
- 5.7 Making the electrical connection
- 5.8 Installing the outside temperature sensor
- 5.9 Setting the DIP switches of the external unit
- 6 Commissioning
- 6.1 Before commissioning
- 6.2 Commissioning the system for the first time
- 6.2.1 Providing the external unit with a power supply ahead of commissioning
- 6.2.2 providing the external unit with a power supply during commissioning
- 6.2.3 Connecting the CANBUS cable to the hybrid manager unit
- 6.2.4 Making the power supply connection
- 6.2.5 Switching on the hybrid system
- 6.2.6 Connecting the programming unit to the hybrid control module
- 6.2.7 Connecting the heat source to the hybrid manager
- 6.2.8 Communication error from External unit on initial power ON of External Unit and Hybrid Manager
- 6.2.9 Adjusting the Hybrid manager circulating pump in the hybrid manager
- 6.2.10 System with series buffer tank
- 6.2.11 Venting the hybrid manager
- 6.2.12 Setting the bypass valve
- 6.2.13 Setting parameters for optimising energy use and costs of the hybrid system
- 6.2.14 Explanation of the parameters for energy and cost optimization of the hybrid system (control strategy)
- 6.2.15 Control Strategy: Option CO2 Optimised and co2 :cost mix
- 6.2.16 Control Strategy: Co2 optimised (environmental factors)
- 6.2.17 Control Strategy: CO2: Cost mix
- 6.2.18 Control Strategy: Option changeover temperature
- 6.2.19 Control Strategy: Cost optimised
- 6.2.20 Control strategy: hydraulic connection
- 6.2.21 Control strategy: Delay time for boiler heating
- 6.2.22 Control strategy: Temperature diff for boiler switch ON
- 6.2.23 Setting parameters at the hybrid control module
- 6.2.24 Commissioning of the air to water heat pump at outside temperatures outside the standard operating range
- 6.2.25 Informing the customer and handing over the technical documents
- 7 Operation
- 8 Environmental protection/disposal
- 9 Inspection and maintenance
- 10 Faults
- 10.1 Faults that are not displayed
- 10.2 Displayed faults
- Overview of internal hybrid fault indicators locations
- 10.2.1 Fault displays on the hybrid control module
- 10.2.2 Check temperature sensor of hybrid manager
- 10.2.3 Faults of the FW200 programming unit
- 10.2.4 Fault display on the FW 200 weather-compensated controller at user level
- 10.2.5 Fault display on the rear of the hybrid manager
- 10.2.6 External unit faults
- 10.2.7 Check components
- 10.2.8 DC fan motors/check PCB
- 10.2.9 Check external unit temperature sensor
- 10.2.10 Check linear expansion valves (LEV)
- 11 Replace components
- 11.1 Pumping refrigerant back into the external unit
- 11.2 Removing the casing from the external unit
- 11.3 Replacing the fan motor
- 11.4 Replacing the PCB housing
- 11.5 Replacing PCBs
- 11.6 Replacing faulty temperature sensors TH3, TH6 or TH33
- 11.7 Replacing outside temperature sensor TH7
- 11.8 Replacing temperature sensors TH4 and TH32
- 11.9 Fitting and removing the linear expansion valve
- 11.10 Removing the transformer (ACL)
- 12 Filling the refrigerant circuit
- 13 Appendix
- 13.1 Cost weighting electricity price — gas price
- 13.2 System wiring (heatronic III boiler connections) with a bypass valve and one unmixed heating circuit
- 13.3 System wiring (CUS boiler connections) with a bypass valve and one unmixed heating circuit
- 13.4 Wiring to PCB in the external unit (heat pump)
- 13.5 Controller circuit board in external unit
- 13.6 Alternative pipe work lengths and T
- 14 General details
- 15 Assembly and installation report for the installer
- 16 Commissioning report for the commissioning engineer
COMMISSIONING
6 720 803 687 (2012/11)42
6.2.17 CONTROL STRATEGY: CO2: COST MIX
For this control strategy the Energy: Price ratio and the environmental
factors for both fossil fuel and electricity must be set.
6.2.18 CONTROL STRATEGY: OPTION CHANGEOVER
TEMPERATURE
For this control strategy, the parameter changeover are set correctly.
6.2.19 CONTROL STRATEGY: COST OPTIMISED
For this strategy the energy: Price ratio is required (chapter 13.1,
page 82, table 47).
6.2.20 CONTROL STRATEGY: HYDRAULIC CONNECTION
This determines the function of the pump in the Hybrid Manager.
Operation Display
▶ HYBRID SETTINGS> Control strategy > ( Table 13)
If CO
2
:cost mix is selected the controller will then display the following menu items.
• Energy: price ratio
• Environmental factor fossil fuel
• Environmental factor electrical energy
▶ Select and adjust each of the menu items to the require values
▶ Confirm the selected menu item
▶ Required value:
• Energy: price ratio
– Setting range: 0.0 to 19.9
– Default: 3.3
• Environmental factor fossil fuel
– Setting range: 0.0 to 5.0
– Default: 1.1
• Environmental factor electrical energy
– Setting range: 0.0 to 5.0
– Default: 2.6
▶ Confirm set value
The controller works with the new settings.
Table 16 Energy price ratio and environmental factors for fossil fuel and electricity set.
6720803687-16.1Wo
HYBRID SETTINGS
15
18
12
h
9
21
24
h
3
6
Energy :price ratio
3.3
Operation Display
▶ HYBRID SETTINGS> Control strategy > ( Table 13)
▶Select changeover temperature from the menu
▶ Confirm the selected menu item
▶ Required value:
– Setting range: -20° to 20°
–Default: 6°
▶ Confirm set value
The controller works with the new settings.
Table 17 Outdoor temperature for switching threshold set
6720803687-17.1Wo
HYBRID SETTINGS
15
18
12
h
9
21
24
h
3
6
Changeover
temperature
6 C
Pump Function Description
Serial
(factory default)
The pump provides water circulation around the central heating circuit(s) - used for all hydraulics described in this document
Parallel The pump does not provide water circulation around the central heating circuit(s). For this type os system each heating circuit
has its own pump. (not possible with this system).
Table 18 Hydraulic connection preset