EX80/EX82-IP Infrared Imager EX80/EX82-IP en Installation Manual
EX80/82-IP | en 1 Important safety instructions Type numbers: NEI-808V04-11, NEI-809V04-11, NEI-808V04-21, NEI-809V04-21 NEI-828V04-11, NEI-829V04-11, NEI-828V04-21, NEI-829V04-21, NEI-828V09-11 NEI-829V09-11 | NEI-828V09-21 | NEI-829V09-21 Read, follow, and retain all of the following safety instructions. Heed all warnings on the unit and in the operating instructions. 1. Cleaning - Unpower the unit before cleaning. Follow any instructions provided with the unit.
2 en | 8. 9. 10. EX80/82-IP - an object has fallen into the unit; - unit has been dropped or the unit cabinet is damaged; - unit exhibits a distinct change in performance; - unit does not operate normally when the user correctly follows the operating instructions. Safety check - Safety checks should be performed upon completion of service or repairs to the unit to ensure proper operating condition.
EX80/82-IP | en 3 The full version Installation Manual is available on the enclosed CD-ROM and can be viewed and printed out with Acrobat Reader, which is also on the enclosed CD-ROM. This user guide is the intellectual property of BOSCH Security Systems and is protected by copyright CAUTION! – Camera Grounding - For mounting the camera in potentially damp environments, ensure to ground the system using the ground connection of the power supply connector (see section: Connecting external power supply).
4 en | 1.1 EX80/82-IP Unpacking Parts list (items supplied with unit) - EX80/82IP Infrared Imager™ Assembly - Installation Instructions booklet - Allen Key - EXMB028B or EXMB028W cable management mounting bracket - Extra window (wide illumination beam) for 4-9mm version only - Software CD Items required for installation (not supplied with units) - Mounting hardware - Mounting tools - PC/Laptop with RJ45 Ethernet port - Power supply 1.2 Initial Preparations 1.
EX80/82-IP 2. 2.1 | en 5 Mounting the unit Mounting bracket preparation SET SCREW 1.) Use the supplied Allen Key to remove the setscrew from the supplied mounting bracket. 2.) Separate the two sections of the mounting bracket. 2.2 Cable / Bracket insertion 1.) Carefully feed the Power and Ethernet cables through both sections of the mounting bracket. 2.) Make sure the cables are not kinked, chafed, or split during this procedure. Bosch Security Systems Quick Install MAN80/82IPB Rev.0 | 2008.
6 en | 2.3 EX80/82-IP Mounting bracket attachment 1.) Attach the Mounting Bracket to the Camera’s Mounting Block using the six bolts supplied with the bracket 2.) Snug the two halves of the bracket together with the Allen head set screw 3.) Tighten the setscrew enough so that the camera can be adjusted for angle. Do not over-tighten. 4.) Note the angled part of the mounting bracket faces to the rear of the camera 2.
EX80/82-IP | en 7 Camera Setup: To determine if the camera is receiving a picture: 1.) Make sure the supplied software is installed in your PC/laptop computer (For Camera Configuration and Software Viewing Setup, refer to full version Installation Manual available on the enclosed CD-ROM -Section 4). 2.) Connect the camera to the PC/laptop and power up the camera. Follow the prompts. See section 2 of full version Installation Manual available on the enclosed CD-ROM for more detail. 3.
8 en | 2.6. EX80/82-IP Vari-focal and “auto iris” control adjustment Note: Use Infra-Red Pass filter to cover the lens during focusing to simulate low light conditions on scene for correct 24-hour focusing. For camera with manual iris lens, the camera should be focused with i the lens iris fully opened to simulate the worst possible depth of field. Using a Infra-Red Pass filter will ensure the iris is fully open for correct setup and adjustment.
EX80/82-IP ! 2.7 | en CAUTION! The CCD image sensors are highly sensitive and require special care for proper performance and extended lifetime. Do not expose them to direct sunlight or bright spot lights in operating and non-operating conditions. Window Selection Narrow Window Wide Window 2.
10 en | EX80/82-IP The EX80/82IP needs to be powered-up while making the LED power adjustments. Cover the photocell to turn the LEDs “ON” (850nm LEDs will have a slight red glow). Adjust the LED power if they are too bright or too dim. For IR power adjustment, rotate VR1. Clockwise is high and counter-clockwise is low 2.9 Photocell Adjustment The photocell is factory set optimum level. In some conditions such as with bright foreground objects the camera may switch too early or too late.
Americas Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, Pennsylvania 17601 USA Telephone +1 888-289-0096 Fax +1 585-223-9180 Email: security.sales@us.bosch.com www.boschsecurity.us Europe, Middle East, Africa: Bosch Security Systems B.V. P.O. Box 80002 5600 JB Eindhoven, The Netherlands Phone: + 31 40 2577 284 Fax: +31 40 2577 330 emea.securitysystems@bosch.com www.boschsecurity.
