User Manual
Table Of Contents
- [en] Instructions for installation and use
- Table of contents
- [en] Instructions for installation and use
- ( Important safety information
- Important safety information
- : Warning
- : Warning
- : Warning
- : Warning
- : Warning
- : Warning
- Causes of damage
- Saving energy
- Environmentally-friendly disposal
- Exhaust air mode
- Air recirculation
- Control panel
- Setting the fan
- Intensive setting
- Fan run-on time
- Lighting
- Cleaning agents
- Cleaning the metal mesh grease filters
- Removing metal grease filter
- Installing the metal mesh grease filter
- Malfunction table
- Replacing bulbs
- LED lights
- Accessories
- ( Important safety information
- Important safety information
- : Warning
- : Warning
- : Warning
- : Warning
- : Warning
- : Warning
- : Warning
- : Warning
- K General information
- Exhaust air mode
- Exhaust duct
- Electrical connection
- Preparing the units
- Appliance dimensions and safety clearances
- 1. Make the cut-out for the exhaust air pipe. To do this, make an opening in the top or back panel of the fitted unit with an additional recess for the power cord.
- 2. If the cabinet base is in place, remove it. Mark the fastening points on the inside of the cabinet and use a bradawl to make indentations where the holes are to be. To help you mark the fastening points, use the fastening piece provided.
- Body wall thickness: 16 mm
- Body wall thickness: 19 mm
- Appliance dimensions and safety clearances
- Preparing the appliance
- Sliding the appliance up into place
- Sliding out the appliance
- Note:
- 1. Use a flat-blade screwdriver to push in the fastening bolt, and turn it 90° until it locks into place. ¨
- 2. Push in the fastening bolt gently with your fingers, and turn it until it comes out of the housing along with the spring.©
- 3. Carefully remove the appliance.
- 4. Screw in the filler strip fully.
- 5. Push in the fastening bolt and turn it 90°.
- Note:
- Note:
- Final fitting stage
- Connecting the pipes
- Removing the appliance
en Customer service
8
Replacing bulbs
These instructions apply to several appliance variants. It
is possible that individual features are described which
do not apply to your appliance.
:Warning
Risk of burns!
Halogen bulbs become very hot when switched on.
There is still a risk of burning for some time after they
have been switched off. Allow the halogen bulbs to cool
down before replacing them.
:Warning
Risk of electric shock!
When changing the bulbs, the bulb socket contacts are
live. Before changing the bulb, unplug the appliance
from the mains or switch off the circuit breaker in the
fuse box.
Important! Only use bulbs of the same type and
wattage.
Replacing halogen bulbs
Note: When inserting halogen bulbs, do not touch the
glass tube. Use a clean cloth to insert the halogen
bulbs.
1. Carefully remove the bulb ring using a suitable tool.
2. Pull out the bulb and replace it with a bulb of the
same type.
3. Insert the bulb cover.
4. Insert the mains plug or switch on the fuse again.
LED lights
Defective LED lights may be replaced by the
manufacturer, their customer service or a qualified
technician (electrician) only.
:Warning
Risk of injury!
The light emitted by LED lights is very dazzling, and can
damage the eyes (risk group 1). Do not look directly
into the switched on LED lights for longer than
100 seconds.
4Customer service
Customer service
When calling us, please give the product number
(E no.) and the production number (FD no.) so that we
can provide you with the correct advice. The rating plate
with these numbers can be found inside the appliance
(remove the metal mesh grease filter to gain access).
You can make a note of the numbers of your appliance
and the telephone number of the after-sales service in
the space below to save time should it be required.
Please be aware that a visit by an after-sales engineer
will be charged if a problem turns out to be the result of
operator error, even during the warranty period.
Please find the contact data of all countries in the
enclosed customer service list.
To book an engineer visit and product advice
Rely on the professionalism of the manufacturer. You
can therefore be sure that the repair is carried out by
trained service technicians who carry original spare
parts for your appliances.
Accessories
(not included in the scope of delivery)
Note: These instructions apply to several appliance
models. It may be the case that an optional accessory
that is listed does not apply for your appliance.
Note: Observe the installation instructions in the
accessory.
--------
E no. FD no.
After-sales serviceO
GB 0344 892 8979
Calls charged at local or mobile rate.
IE 01450 2655
0.03 € per minute at peak. Off peak 0.0088 €
per minute.
Accessory Order number
Basic equipment:
Starter set for circulating-air mode
Throw-away filter for starter set
DSZ4565
DSZ4561
Basic equipment:
CleanAir air recirculation module
Throw-away filter for CleanAir recirculation mod-
ule
DSZ4680
DSZ4681
Lowering frame:
Appliance width: 60 mm DSZ4660
Lowering frame:
Appliance width: 90 cm DSZ4960
Installation set:
Upper cabinet: 90 cm DSZ4920
Handle strip: 60 cm:
Stainless steel
White
Black
DSZ4655
DSZ4652
DSZ4656
Handle strip: 90 cm:
Stainless steel
White
Black
DSZ4955
DSZ4952
DSZ4956