User Manual
Table Of Contents
- [en] Instructions for installation and use
- Table of contents
- [en] Instructions for installation and use
- ( Important safety information
- Important safety information
- : Warning
- : Warning
- : Warning
- : Warning
- : Warning
- : Warning
- Causes of damage
- Saving energy
- Environmentally-friendly disposal
- Exhaust air mode
- Air recirculation
- Control panel
- Setting the fan
- Intensive setting
- Fan run-on time
- Lighting
- Cleaning agents
- Cleaning the metal mesh grease filters
- Removing metal grease filter
- Installing the metal mesh grease filter
- Malfunction table
- Replacing bulbs
- LED lights
- Accessories
- ( Important safety information
- Important safety information
- : Warning
- : Warning
- : Warning
- : Warning
- : Warning
- : Warning
- : Warning
- : Warning
- K General information
- Exhaust air mode
- Exhaust duct
- Electrical connection
- Preparing the units
- Appliance dimensions and safety clearances
- 1. Make the cut-out for the exhaust air pipe. To do this, make an opening in the top or back panel of the fitted unit with an additional recess for the power cord.
- 2. If the cabinet base is in place, remove it. Mark the fastening points on the inside of the cabinet and use a bradawl to make indentations where the holes are to be. To help you mark the fastening points, use the fastening piece provided.
- Body wall thickness: 16 mm
- Body wall thickness: 19 mm
- Appliance dimensions and safety clearances
- Preparing the appliance
- Sliding the appliance up into place
- Sliding out the appliance
- Note:
- 1. Use a flat-blade screwdriver to push in the fastening bolt, and turn it 90° until it locks into place. ¨
- 2. Push in the fastening bolt gently with your fingers, and turn it until it comes out of the housing along with the spring.©
- 3. Carefully remove the appliance.
- 4. Screw in the filler strip fully.
- 5. Push in the fastening bolt and turn it 90°.
- Note:
- Note:
- Final fitting stage
- Connecting the pipes
- Removing the appliance
Trouble shooting en
7
In the dishwasher:
Note: If the metal mesh grease filters are cleaned in the
dishwasher, slight discolouration may occur. This has
no effect on the function of the metal mesh grease
filters.
■ Do not clean heavily soiled metal mesh grease filters
together with utensils.
■ Place the metal mesh grease filters loosely in the
dishwasher. The metal mesh grease filters must not
be wedged in.
Removing metal grease filter
1. Open the lock and fold down the metal grease filter.
While doing this, place your other hand under the
metal grease filter.
2. Take the metal grease filter out of the holder.
Notes
– Fat may accumulate in the bottom of the metal
grease filter.
– Hold the metal grease filter level to prevent
grease from dripping out.
3. Clean the metal grease filter.
On appliances with a glass plate in the filter pull-out:
■ The glass plate can be removed easily and can be
cleaned in the dishwasher.
■ To remove it, carefully lift the glass plate.
Installing the metal mesh grease filter
1. Insert the metal mesh grease filter.
While doing this, place the other hand under the
metal mesh grease filter.
2. Fold the metal mesh grease filter upwards, locking it
in place.
3Trouble shooting
Trouble shooting
Malfunctions often have simple explanations. Please
read the following notes before calling the after-sales
service.
:Warning
Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be
carried out and damaged power cables replaced by
one of our trained after-sales technicians. If the
appliance is defective, unplug the appliance from the
mains or switch off the circuit breaker in the fuse box.
Contact the after-sales service.
Malfunction table
--------
Problem Possible cause Solution
The appliance
does not work
The plug is not
plugged in.
Connect the appliance to the
electricity supply
Power cut Check whether other kitchen
appliances are working
Faulty fuse Check in the fuse box to make
sure that the fuse for the
appliance is OK
The lighting does
not work.
The bulbs are
faulty.
For information on changing
the bulbs, see the "Replacing
Bulbs" section.