Specifications

ISW-D8125CW-V2 | Installation and Operation Guide | Overview
.
Bosch Security Systems, Inc. | 8/11 | F01U161691-05 3
1.0 Overview
The ISW-D8125CW-V2 is an integrated commercial
wireless interface module and keypad. The keypad
accesses the programming and diagnostic functions of
the wireless portion of the system. The integrated
keypad on the commercial wireless interface module
looks different from the typical keypads (D1255,
D1256, D1257, and so on) so that it is not mistaken for
a system keypad.
The commercial wireless interface module must be
mounted within 5 ft of the control panel. It is designed
so that it is mounted right next to the D8103, D8108A
or D8109 enclosure.
The commercial wireless interface module is
compatible with the following control panels:
• GV3 Series: D9412GV3, D7412GV3, D7212GV3
• GV2 Series: D9412GV2, D7412GV2, D7212GV2
• G Series: D9412G, D7412G, D7212G*
• 9000 Series: D9412, D9112*, D7412, D7212*
* These control panels must have Firmware 6.5 or later
installed (Firmware 6.51 or later for the D7212G).
All of the compatible control panels can have both
hardwired (D8128D OctoPOPITS, D8125 Popex /
D9127 POPITS, D8125MUX) and wireless points
connected at the same time.
To add wireless points, an Inovonics Echostream
EN4200 Serial Receiver must be connected to the
commercial wireless interface module which is then
connected to the control panel’s ZONEX 1 (and/or
ZONEX 2) terminals and Aux Power. For best
transmitter reception results, the EN4200 Serial
Receiver should be centrally located among the
transmitters. If transmitters are at too great of a
distance for the EN4200 Receiver to pick up the
transmission, install an EN5040-T RF Repeater.
1.1 FCC Compliance Notice, Part 15
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a commercial installation. This
equipment generates, uses, and can radiate radio
frequency energy, and, if not installed in accordance
with the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment on
and off, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment
and the receiver.
3. Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio/TV
technician for help.
1.2 Features
• The commercial wireless interface module features
a menu-driven user interface.
• The commercial wireless interface module
supports the following number of Bosch
commercial wireless transmitters:
- 234 transmitters (117 per bus) on the D9112
and all versions of the D9412
- 65 transmitters on all versions of the D7412
- 32 transmitters on all versions of the D7212
Points 74 and 75 on ZONEX 1 and
Points 194 and 195 on ZONEX 2 cannot
be used for any device other than the
ISW-EN1224-ON Keyfob.
• The commercial wireless interface module
provides diagnostic functions to troubleshoot RF
transmitters.
• The commercial wireless interface module features
a fixed device check-in time of 3 minutes.
• The commercial wireless interface module features
a programmable system supervision interval.