ISW-D8125CW-V2 Installation and Operation Guide EN Inovonics Echostream Interface Module
ISW-D8125CW-V2 | Installation and Operation Guide | Contents Contents 1.0 1.1 1.2 1.3 1.4 1.5 1.6 2.0 2.1 2.2 2.3 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 4.0 4.1 4.2 4.3 4.4 4.5 4.6 5.0 2 Overview ...............................................................................................................................................................3 FCC Compliance Notice, Part 15....................................................................................................................
ISW-D8125CW-V2 | Installation and Operation Guide | Overview . 1.0 Overview The ISW-D8125CW-V2 is an integrated commercial wireless interface module and keypad. The keypad accesses the programming and diagnostic functions of the wireless portion of the system. The integrated keypad on the commercial wireless interface module looks different from the typical keypads (D1255, D1256, D1257, and so on) so that it is not mistaken for a system keypad.
ISW-D8125CW-V2 | Installation and Operation Guide | Overview 1.3 Specifications Table 1: Commercial Wireless Interface Module Specifications Specification User Interface Operating Voltage Current Operating Temperature Wiring Dimensions (HxWxD) Value - LCD Display: 2 lines x 16 characters, backlit - Keypad: 0-9 numbers; ESC, ENT, PREV, NEXT and DIAG keys 10.2 - 14 VDC supplied by Aux Power from Control Panel or an External Auxiliary Power Supply.
ISW-D8125CW-V2 | Installation and Operation Guide | Installation . 2.0 Installation The commercial wireless interface module is packaged with a Point Label Sheet. Save these, as you will use them when identifying the point numbers on the Bosch transmitters. 2.1 2.1.1 The commercial wireless interface module supports up to two ISW-EN4200 Receivers. By default, the commercial wireless interface module supports one receiver. Refer to Figure 3 to set the RCV pins.
ISW-D8125CW-V2 | Installation and Operation Guide | Installation Connect the wiring (refer to Figure 6 on page 7, or Figure 7 on page 8) to the commercial wireless interface module and mount the cover unit to the base. 4. Figure 5: ISW-D8125CW-V2 Mounting Options 1 2 For best transmitter reception results, place the EN4200 Serial Receiver in a central location among the transmitters.
ISW-D8125CW-V2 | Installation and Operation Guide | Installation .
ISW-D8125CW-V2 | Installation and Operation Guide | Installation Figure 7: ISW-D8125CW-V2 to D7412 and D7212 (GV3, GV2, and G) Control Panel Wiring Diagram TX Vs 2 GND RX ZONEX OUT 1 28 ZONEX IN 1 27 NOT USED 26 NOT USED 25 ZONEX POWER + 24 ZONEX COMMON 23 3 TX Vs GND RX ZONEX BUS RECEIVER 1 RX2 GND TX2 +12V RX1 GND TX1 +12V GND IN OUT +12V 4 RECEIVER 2 1 1- ISW-D8125CW-V2 connected to Zonex 1 on control panel (Points 9-127) (D7412: Points 9-75; D7212: Points 9-40) 2- Contro
ISW-D8125CW-V2 | Installation and Operation Guide | Operation . 3.0 Operation 3.1 Commercial Wireless Interface Module Quick Startup Recommendations The following information details the recommended programming steps that should be taken when installing a commercial wireless interface module in a new installation. 1. Press the [2] key and change the Installer Passcode, if necessary. Refer to Section 3.9.6 Changing the Installer Passcode on page 13. 3.
ISW-D8125CW-V2 | Installation and Operation Guide | Operation Table 2: Key ESC ENT PREV NEXT DIAG Key Descriptions Description Escape: Backs out of a programming option or menu level. Enter: Accepts a program entry. Manually scrolls to a previous menu or point selection. This key also stops the autoscrolling of the menus. Manually scrolls to the next menu or point selection. This key also stops the autoscrolling of the menus. Shortcut to RF Diagnostics menu (see Section 3.9.9 RF on page 14).
ISW-D8125CW-V2 | Installation and Operation Guide | Operation . 3.9 Keypad Menus After you enter the passcode and press the [ENT] key, the keypad scrolls through the main menu. The keypad displays each option for three seconds. 3.9.1 Add or Edit an RF Transmitter To add a new RF transmitter, or to edit one already added to the system: 1. From the idle text screen, enter the passcode and press [ENT] to access the main menu. 2. Press [1] to add or edit an RF Transmitter (RF Xmtr). 3.
ISW-D8125CW-V2 | Installation and Operation Guide | Operation 5. At the RF Transmitter Menu (Figure 18), select the desired action: - - 3.9.2 Push 1 to edit: Press [1] to change the RF transmitter’s point type. Push 2 to delete: Press [2] to delete the RF transmitter from the system. Refer to Section 3.9.5 Deleting an RF Transmitter on page 13. Push 3 to continue: Press [3] to add a new RF transmitter, or change an existing one. To add a new RF transmitter, refer to Section 3.9.
ISW-D8125CW-V2 | Installation and Operation Guide | Operation . 3.9.4 Adding an Existing RF Transmitter It may be necessary to add an already installed transmitter again to the commercial wireless interface module, especially if the transmitter was deleted using the RF Transmitter menu option (refer to Section 3.9.1 Add or Edit an RF Transmitter on page 11). In this case, the RF transmitters can be re-added to the commercial wireless interface module.
ISW-D8125CW-V2 | Installation and Operation Guide | Operation 3.9.7 Clearing the EEPROM Clearing the EEPROM erases the entire point database and resets the commercial wireless interface module to the factory default settings. Ensure that you have a printed copy of the programming settings so you can manually restore them after clearing the EEPROM.
ISW-D8125CW-V2 | Installation and Operation Guide | Operation . The keypad shows the point number status. Figure 20: RF Point Number Status 3.10 Other Programming Functions 3.10.1 Programming the ISW-EN5040-T Repeater If it is necessary to install an ISW-EN5040-T Repeater into this system, it must be programmed as an RF transmitter. Refer to Section 3.9.3 Adding a New RF Transmitter on page 12. The repeater only sends Low Battery Reports and Tamper Reports.
ISW-D8125CW-V2 | Installation and Operation Guide | Operation If both a Tamper and Fault condition occur, the Tamper condition takes priority over the Fault condition and an open condition is sent to the control panel. Therefore, Bosch Security Systems, Inc. recommends the following: - - Controlled points be programmed as ‘Instant alarm on Open’ when armed and ‘Trouble’ when disarmed. 24 Hour points be programmed as ‘Instant alarm on Open’. Fire points be programmed as ‘Trouble on Open’.
ISW-D8125CW-V2 | Installation and Operation Guide | Troubleshooting . 4.0 Troubleshooting 4.1 Troubleshooting Solutions Symptom Diagnosis Remedy Commercial wireless interface module has lost communications with the EN4200. This causes all programmed RF points on that commercial wireless interface module to go missing immediately (missing alarms or missing troubles at control panel.) It will also cause a Point Bus Fail 1 (or 2) at the control panel. Check for LED activity at receiver(s).
ISW-D8125CW-V2 | Installation and Operation Guide | Troubleshooting Symptom Diagnosis Remedy Received signal level for that point is low. A second EN4200 receiver can be installed in a different location to increase range. A Bosch EN5040-T high-power repeater may be used to increase range to a greater degree. Use the EN7016 to test the signal range.
ISW-D8125CW-V2 | Installation and Operation Guide | Troubleshooting . 4.2 EN4200 Receiver Supervision The commercial wireless interface module supervises the Bosch EN4200 receiver by periodically polling it. If the EN4200 does not respond to the polls over a 165-sec period, the commercial wireless interface module will initiate a Point Bus Trouble event back to the control panel. The control panel will then initiate a Point Bus Fail 1 (or 2) event. If this occurs, the keypad shows Figure 21.
ISW-D8125CW-V2 | Installation and Operation Guide | Troubleshooting Why can’t I program more than one RF transmitter per point? Programming more than a single transmitter to a given point number defeats the ability of the Inovonics Echostream system to supervise itself. This is a practice called "stacking points" and is discouraged in practice. Never stack points in a life-safety or security application. Can I externalize an antenna? No. The EN5040-T acts as an external antenna.
ISW-D8125CW-V2 | Installation and Operation Guide | Program Record Sheet . 5.
ISW-D8125CW-V2 | Installation and Operation Guide | Program Record Sheet Point # 22 Point Type Transmitter Type Loop Type (External Contact) (circle one) EOL Resistor? Internal Contacts (Magnetic) Used? N/O or N/C Yes / No Yes / No N/O or N/C Yes / No Yes / No N/O or N/C Yes / No Yes / No N/O or N/C Yes / No Yes / No N/O or N/C Yes / No Yes / No N/O or N/C Yes / No Yes / No N/O or N/C Yes / No Yes / No N/O or N/C Yes / No Yes / No N/O or N/C Yes / No Yes / No N/O or N/C Ye
ISW-D8125CW-V2 | Installation and Operation Guide | Program Record Sheet .
Bosch Security Systems, Inc. 130 Perinton Parkway Fairport, NY 14450 USA www.boschsecurity.com © Bosch Security Systems, Inc.
