User manual
Table Of Contents
- Index
- 1 Key to symbols and safety instructions
- 1.1 Key to symbols
- 1.2 Safety information
- 2 Standard delivery
- 3 Appliance details
- 4 Installation instructions
- 4.1 Tools required
- 4.2 Location requirements
- 4.3 Secure the appliance
- 4.4 Water piping
- 4.4.1 Inlet - Outlet connections
- 4.4.2 Dielectric joint (not supplied with the appliance)
- 4.4.3 Condensate Drain Tubes (not supplied with the appliance)
- 4.4.4 TPR Valve (supplied with the appliance)
- 4.4.5 Thermal expansion tank (not supplied with the appliance)
- 4.4.6 Temperature mixing device (not supplied with the appliance)
- 4.4.7 Pressure limiting valve (not supplied with the appliance)
- 4.4.8 Expansion control valve (not supplied with the appliance)
- 4.5 Electric requirements
- 4.6 Installation configurations
- 4.7 Insulation blanket
- 4.8 Fill the water storage tank
- 4.9 Installation checklist
- 4.10 What to expect for “normal startup”
- 4.11 Off-peak compatibility
- 5 Operation Instructions
- 5.1 Safety warnings
- 5.2 Working display
- 5.3 Working modes
- 5.4 „Operating“ menu
- 5.5 Temperature set point
- 5.6 „Main“ menu
- Accessing the „Main“ menu
- 5.6.1 „Mode“ function - heating modes
- 5.6.2 „Prog“ function - Timetable operation programming
- 5.6.3 Silent Mode programming - „Sil“ function
- 5.6.4 „Leg“ function - automatic thermal disinfection
- 5.6.5 „Set“ function - adjustments
- 5.6.6 „Purg“ function - purge
- 5.6.7 „Info“ function - information
- 5.7 Troubleshooting
- 5.8 Factory configurations
- 5.9 Selecting the temperature units - „C“ or „F“
- 5.10 Setting the time and day of the week
- 5.11 Controls
- 6 Maintenance and repair
- 6.1 Periodic Inspection
- 6.2 Temperature and pressure relief valve (PTR Valve)
- 6.3 Flushing tank
- 6.4 Draining the Water Heater
- 6.5 Vacation and Extended Shutdown
- 6.6 Clearing the Condensation Drain Tubes
- 6.7 Refrigerant circuit
- 6.8 Anode Rod servicing
- 6.9 Checking/replacing the magnesium anode
- 6.10 Service menu
- 7 Display
- 8 Electrical diagram
- 9 Environmental protection
- 10 Warranty details
6 720 801 244 (2013/08) Compress 3000 DW FO
32 | Operation Instructions
▶ Press „-“.
Displays with blinking „del“ indication.
Fig. 37 „del“ function
▶Press „ok“.
The meter restarts the count.
5.7 Troubleshooting
This device is equipped with a troubleshooting function. Error
indication is performed by means of a code (Table 6, page 40)
corresponding to the error indication symbol in the digital
display (Fig. 17, [6]). In most cases, the device will only return
to normal functioning following elimination of the cause of the
malfunction and resetting of the device.
To identify the malfunction, see Section 7.
Fig. 38 Error code
Resetting the system
▶ Press the „ok“ key and hold it down for more than 3
seconds.
Fig. 39 Resetting the system
5.8 Factory configurations
Upon setting the temperature units and timetable, the device
will operate according to the factory set values.
Heating mode: „Combi“ ( section 5.6.1)
Manual functioning: „manual“ ( section 5.4)
Fig. 40 Initial menu
5.9 Selecting the temperature units - „°C“ or „°F“
Upon the 1
st
use, the user must select the temperature unit.
Fig. 41 Selecting the temperature units
▶ Press the „+“ or „-“ key to select the temperature unit.
6720646160-42.1V
6720800765-04.1V
menu
-
ok
+
6720646160-21.1V
menu
-
ok
+
>3s
6720801244-01.1V
6720646160-34.1V