Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Certifications, approvals, listings, and safety
- Introduction
- System overview
- Installation checklist
- Control panel installation
- Power supply
- Telephone communications
- IP communications
- Keypads, keyswitches, keyfobs and transmitters
- Keypads
- B915 Basic Keypad
- B920 Two-line Alphanumeric Keypad
- B921C Two-line Capacitive Keypad with Inputs
- B930 ATM Style Alphanumeric Keypad
- B942 Touch Screen Keypad
- Shortcuts and custom functions
- Address settings
- Supervision
- Installation and control panel wiring (keypads)
- Sensor loops overview and wiring (B921C/B942/B942W only)
- Output wiring (B942/B942W only)
- Troubleshooting
- Keyswitches
- RADION keyfobs and Inovonics pendant transmitters
- Keypads
- On-board outputs
- Off-board outputs
- On-board points
- Off-board points
- Wireless modules
- Access control
- Program and test the control panel
- Control panel board overview
- System wiring diagrams
- Approved applications
- Keypad Installer menu
- [1] Program menu
- [1] Reporting > [1] Phone menu parameters
- [1] Reporting > [2] Network menu parameters
- [1] Reporting > [3] Routing menu parameters
- [1] Reporting > [4] Personal Note menu parameters
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [1] Module Parameters menu
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [2] Address Parameters menu
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [3] DNS Parameters menu
- [2] Network > [2] Cellular > (choose the SDI2 cellular module or plug-in module)
- [3] RPS > [1] RPS Passcode menu parameters
- [3] RPS > [2] RPS Phone Number menu parameters
- [3] RPS > [3] RPS IP Address menu parameters
- [3] RPS > [4] RPS Port Number menu parameters
- [4] Area Options menu parameters
- [5] Keypad menu parameters
- [6] Users menu parameters
- [7] Points menu parameters
- [8] Disable Programming menu
- [2] Wireless menu
- [1] RF Point Menu> [1] Enroll Point RFID
- [1] RF Point Menu> [2] Replace Point RFID
- [1] RF Point Menu> [3] Remove Point RFID
- [2] RF Repeater Menu > [1] Add Repeater
- [2] RF Repeater Menu > [2] Replace Repeater
- [2] RF Repeater Menu > [3] Remove Repeater
- [3] RF Diagnostic Menu > [1] RF Points
- [3] RF Diagnostic Menu > [2] RF Repeater Menu
- [3] Diags menu
- [4] Serv Byp (Service Bypass) menu
- [5] Versions menu
- [6] Cloud menu
- [1] Program menu
- Specifications
- Appendix
- Back Page
Panel event Modem4 code
D6500 mode
Modem4 code
Bosch SIA mode
Contact ID event Contact ID code
Missing Supervision MTpppp NriaaBZpppp Loss of Supervision –RPM 1 382 aa ppp
Missing Trouble Vpppp NriaaUYpppp Loss of Supervision - RPM 1 382 aa ppp
Network Cable Connected NsD43 NpiddddNR010 System Peripheral Trouble
Restore
3 330 00 zzz
Network Cable Disconnected NsD42 NpiddddNT010 System Peripheral Trouble 1 330 00 zzz
Non-Fire Cancel Alarm \siiii Nriaa/idiiiiBC Cancel 1 406 aa uuu
Normal start-up of the
control panel
NsD14 NRR System Reset 1 305 00 000
Opening by Account OSiiii NidiiiiOP O/C by account 1 401 00 uuu
Opening by Area Osiiii Nriaa/idiiiiOP O/C by user 1 401 aa uuu
Opening Early by Area Osiiii Nriaa/idiiiiOK Early O/C 1 451 aa uuu
Opening Late by Area Osiiii Nriaa/idiiiiOJ Late O/C 1 452 aa uuu
Parameters changed NsD02 NYG Panel Programming
Changed
1 306 00 000
Personal Notification
Communication Trouble
TsB01 NpiddddYS Communication Trouble 1 350 0 zzz
Personal Notification
Communication Trouble
Restore
NsB01 NpiddddYK Communication Trouble
Restore
3 350 0 zzz
Phone Line Missing 1 TsssB NLT1 Telco 1 Fault 1 351 00 000
Phone Line Restored 1 RsssB NLR1 Telco 1 Fault Restore 3 351 00 000
Popex Bus Fault TsssD NYI PS Over Current 1 312 00 ZZZ
Popex Bus Fault Restore RsssD NYJ PS Over Current Restore 3 312 00 ZZZ
Popex Invalid Popit TsssD NYI PS Over Current 1 312 00 ZZZ
Popex Invalid Popit Restore RsssD NYJ PS Over Current Restore 3 312 00 ZZZ
Popex Low Voltage TsssD NYI PS Over Current 1 312 00 ZZZ
Popex Low Voltage Restore RsssD NYJ PS Over Current Restore 3 312 00 ZZZ
Programming Started TsssF NiduuuuTS System Shutdown 1 308 00 iii
Programming Finished RsssF NiduuuuTE System Shutdown Restore 3 308 00 iii
RAM Fail with RPS TsF02 NRA Unsuccessful access 1 413 00 000
Re-Boot NsD14t NRR System Reset 1 305 00 000
Relay Reset by Sked NsD20 NaikkkROrrrr Sounder/Relay Reset 3 320 00 000
Relay Reset by User NsD18 NidiiiiROrrrr Sounder/Relay Reset 3 320 00 000
Relay Set by Sked NsD19 NaikkkRCrrrr Sounder/Relay Set 1 320 00 000
Control Panel Appendix | en 157
Bosch Security Systems, Inc. Installation and System Reference Guide 2016.05 | 14 | F.01U.287.180