Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Certifications, approvals, listings, and safety
- Introduction
- System overview
- Installation checklist
- Control panel installation
- Power supply
- Telephone communications
- IP communications
- Keypads, keyswitches, keyfobs and transmitters
- Keypads
- B915 Basic Keypad
- B920 Two-line Alphanumeric Keypad
- B921C Two-line Capacitive Keypad with Inputs
- B930 ATM Style Alphanumeric Keypad
- B942 Touch Screen Keypad
- Shortcuts and custom functions
- Address settings
- Supervision
- Installation and control panel wiring (keypads)
- Sensor loops overview and wiring (B921C/B942/B942W only)
- Output wiring (B942/B942W only)
- Troubleshooting
- Keyswitches
- RADION keyfobs and Inovonics pendant transmitters
- Keypads
- On-board outputs
- Off-board outputs
- On-board points
- Off-board points
- Wireless modules
- Access control
- Program and test the control panel
- Control panel board overview
- System wiring diagrams
- Approved applications
- Keypad Installer menu
- [1] Program menu
- [1] Reporting > [1] Phone menu parameters
- [1] Reporting > [2] Network menu parameters
- [1] Reporting > [3] Routing menu parameters
- [1] Reporting > [4] Personal Note menu parameters
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [1] Module Parameters menu
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [2] Address Parameters menu
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [3] DNS Parameters menu
- [2] Network > [2] Cellular > (choose the SDI2 cellular module or plug-in module)
- [3] RPS > [1] RPS Passcode menu parameters
- [3] RPS > [2] RPS Phone Number menu parameters
- [3] RPS > [3] RPS IP Address menu parameters
- [3] RPS > [4] RPS Port Number menu parameters
- [4] Area Options menu parameters
- [5] Keypad menu parameters
- [6] Users menu parameters
- [7] Points menu parameters
- [8] Disable Programming menu
- [2] Wireless menu
- [1] RF Point Menu> [1] Enroll Point RFID
- [1] RF Point Menu> [2] Replace Point RFID
- [1] RF Point Menu> [3] Remove Point RFID
- [2] RF Repeater Menu > [1] Add Repeater
- [2] RF Repeater Menu > [2] Replace Repeater
- [2] RF Repeater Menu > [3] Remove Repeater
- [3] RF Diagnostic Menu > [1] RF Points
- [3] RF Diagnostic Menu > [2] RF Repeater Menu
- [3] Diags menu
- [4] Serv Byp (Service Bypass) menu
- [5] Versions menu
- [6] Cloud menu
- [1] Program menu
- Specifications
- Appendix
- Back Page
Port Number
Poll Rate (seconds)
Format
AES Size
AES Entry
B91x/B92x keypads configuration of Enhanced Comm Parameters
1. Enter the installer passcode, and then open the [1] Installer menu.
2. Go to [1] Program > [1] Reporting > [2] Network > [2] Enhanced Comm Parms. The
keypad scrolls the entries for the selected Enhanced Comm destination.
3. Use [PREV] or [NEXT] to go to the destination you want to edit.
4. Press [ENTER] to edit the selected Enhanced Comm destination. The keypad asks if you
want to edit the address.
5. Press [ENTER] to edit the network address. The existing address and an editing cursor
show.
6. Delete existing characters, if necessary, and then enter the new address.
7. Press [ENTER] to save the address. The keypad shows Parameter Saved.
8. Press [NEXT]. The currently configured port number shows, and the keypad asks if you
want to edit it.
9. Press [ENTER] to edit the port number. The existing port number and an editing cursor
show.
10. Delete existing characters, if necessary, and then enter the new rate.
11. Press [ENTER] to save the port. The keypad shows Parameter Saved.
12. Press [NEXT]. The currently configured poll rate shows, and the keypad asks if you want
to edit it.
13. Press [ENTER] to edit the poll rate. The existing poll rate and an editing cursor show.
14. Delete existing characters, if necessary, and then enter the new poll rate.
15. Press [ENTER] to save the poll rate. The keypad shows Parameter Saved.
16. Press [NEXT]. The current format (Modem4 or Contact ID) shows.
17. Press [ENTER] to edit the format.
18. Use [PREV] or [NEXT] to select the desired format, Modem4 or Contact ID.
19. Press [ENTER] to save the format. The keypad shows Parameter Saved.
20. Press [NEXT]. The current AES key size shows.
21. Press [ENTER] to edit the AES key size.
22. Use [PREV] or [NEXT] to select the desired size.
23. Press [ENTER] to save the size. The keypad shows Parameter Saved.
24. .Press [ESC] to return to the list of enhanced comm options, or press and hold [ESC] to
exit the Installer menu.
B93x/B94x keypads configuration of Network Address, Poll Rate (seconds), and Port
Number
1. Enter the installer passcode, and then open the [1] Installer menu.
2. Go to [1] Program > [1] Reporting > [2] Network > [2] Enhanced Comm Parms. The
keypad shows the network address for the selected Enhanced Comm destination.
3. Use
/[PREV] or /[NEXT] to go to the destination you want to edit.
Control Panel
Keypad Installer menu | en 111
Bosch Security Systems, Inc. Installation and System Reference Guide 2016.05 | 14 | F.01U.287.180