AUTODOME 5000 Analog PTZ Camera VEZ-5000 en Operations Manual
AUTODOME 5000 Analog PTZ Camera Table of Contents | en 3 Table of contents 1 Safety 5 1.1 About this Manual 5 1.2 Conventions in this Manual 5 1.3 Legal Information 5 1.4 Important Safety Instructions 5 1.5 Important Notices 7 1.6 FCC and ICES Compliance (Class A) 9 2 Description 11 3 Unpacking 12 3.1 Parts List 12 4 Installation 14 5 Connection 15 5.1 Switches/Connectors 15 5.2 Communication Switch Setting 16 5.3 ID Setting 16 5.
en | Table of Contents AUTODOME 5000 Analog PTZ Camera 6.11.2 Digital Zoom 40 6.12 PTZ Setup 40 6.12.1 Autopan 41 6.12.2 Tour 42 6.12.3 Preset Tour 43 6.12.4 Preset 44 6.12.5 Freeze 46 6.12.6 Home Setting 46 6.12.7 Schedule 47 6.12.8 Misc. Function 48 6.13 Display Setup 48 6.13.1 ID Display 49 6.13.2 Title Display 49 6.13.3 Privacy Masking 50 6.13.4 Time Setting 51 6.13.5 Motion Track 52 6.14 Alarm Setup 52 6.14.1 Alarm Setting 52 6.14.
AUTODOME 5000 Analog PTZ Camera 1 Safety 1.1 About this Manual Safety | en 5 This manual has been compiled with great care and the information it contains has been thoroughly verified. The text was complete and correct at the time of printing. Because of the ongoing development of products, the content of the manual may change without notice.
en | Safety AUTODOME 5000 Analog PTZ Camera 1. Cleaning - Unplug the unit from the outlet before cleaning. Follow any instructions provided with the unit. Generally, using a dry cloth for cleaning is sufficient, but a moist fluff-free cloth or leather shammy may also be used. Do not use liquid cleaners or aerosol cleaners. 2. Heat Sources - Do not install the unit near any heat sources such as radiators, heaters, 3.
AUTODOME 5000 Analog PTZ Camera Safety | en 7 12. Damage requiring service - Unplug the unit from the main AC power source and refer servicing to qualified service personnel when any damage to the equipment has occurred, such as: the power supply cord or plug is damaged; exposure to moisture, water, and/or inclement weather (rain, snow, etc.
en | Safety AUTODOME 5000 Analog PTZ Camera – Ground the cable system if connecting an outside cable system to the unit. – Connect outdoor equipment to the unit's inputs only after this unit has had its grounding plug connected to a grounded outlet or its ground terminal is properly connected to a ground source. – Disconnect the unit's input connectors from outdoor equipment before disconnecting the grounding plug or grounding terminal.
AUTODOME 5000 Analog PTZ Camera 1.6 Safety | en 9 FCC and ICES Compliance (Class A) FCC ET ICES INFORMATION (commercial applications) (U.S.A. and Canadian Models Only, CLASS A) Notice! This is a class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures. This device complies with part 15 of the FCC Rules.
en | Safety AUTODOME 5000 Analog PTZ Camera interférences nuisibles aux communications radio. L’utilisation de ce produit dans une zone résidentielle peut provoquer des interférences nuisibles. Le cas échéant, l’utilisateur devra remédier à ces interférences à ses propres frais. Au besoin, l’utilisateur consultera son revendeur ou un technicien qualifié en radio/télévision, qui procédera à une opération corrective.
AUTODOME 5000 Analog PTZ Camera 2 Description | en 11 Description The AUTODOME 5000 Analog PTZ Dome Camera delivers up to 432x zoom ratio to capture clear image in the distance. Continuous Auto Focus, Back Light, Auto Exposure and Auto SensUp Max functions are provided for clear and high quality image.
en | Unpacking AUTODOME 5000 Analog PTZ Camera 3 Unpacking 3.1 Parts List Quanity Graphic Description 1 Mounting Adapter 1 Dome Camera Body without Sunshield1 1 Dome Camera Body with Sunshield1 1 M5x8L security screw for mounting adapter 1 T20 Security Torx wrench for M5x8L security screw 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
AUTODOME 5000 Analog PTZ Camera Unpacking | en Quanity Graphic Description 1 T10 Security Torx wrench for dome 13 bubble 1 Lubricant 1 User Manual Notice! 1. Your package contains one Dome Camera Body, depending if you purchased an indoor (without sunshield) or an outdoor (with sunshield) camera. Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.
en | Installation 4 AUTODOME 5000 Analog PTZ Camera Installation Follow the instructions below to complete cable connections of the AUTODOME 5000 camera. Connect the camera to other devices as shown in the diagram to complete a video surveillance solution. Figure 4.1: System Configuration 1 Repeater 2 AUTODOME 5000 camera 3 Video cable 4 Switch/Quad/Mux/DVR 5 Main monitor 6 Call monitor 7 Control keyboard Notice! To extend the network distance up to 1.
AUTODOME 5000 Analog PTZ Camera Connection | en 5 Connection 5.1 Switches/Connectors 15 Configuring the camera’s ID and communication protocol is required before connecting the camera to other devices. The switches used for configuring these settings are located on the camera’s back plate. Refer to the diagram and table below for positions and definition of the switches / connectors.
en | Connection 5.2 AUTODOME 5000 Analog PTZ Camera Communication Switch Setting Communication Switch The camera’s communication switches are specified in the table below. Communication Switch Switches Description SW1 SW2 RS-485 Setting SW3 SW4 SW5 Reserved SW6 Reserved RS-485 Setting The camera uses an RS-485 interface to communicate with the control device. For this reason, the RS-485 setup of the camera and the control device must be the same. The default RS-485 setting is half-duplex.
AUTODOME 5000 Analog PTZ Camera Connection | en 17 For users who wish to set up the camera ID via the dip switch at the camera’s back plate, first choose as the setting type under the menu. Then the camera’s ID can be setup using the 10-bit ID dip switch. If the camera’s ID number is 6, for instance, the ID switch SW 2 and SW 3 should be set to “ON” and the rest should be set to “OFF” as shown below.
en | Connection AUTODOME 5000 Analog PTZ Camera Use the 6-bit dip switch (Camera Control Protocol Switch) to set the camera’s control protocol and its baud rate. If protocol “Pelco D” is selected, which is switch no. 01 and baud rate 4800, for instance, set the SW-1 to “ON” and the rest to “OFF” as shown below. 1 2 3 4 5 6 ON 6 5 4 3 2 1 For more switch configurations, refer to Appendices, page 69. 5.
AUTODOME 5000 Analog PTZ Camera 5.7 Connection | en 19 RS-485 Connector Definition Before connecting the RS-485 wires, refer to the illustrations below for definition of the RS-485 connector. RS-485 Connector Switch Bosch Security Systems, Inc. Descriptio Number n SW1 R- SW2 GND SW3 R+ SW4 T- SW5 T+ Operations Manual 2013.07 | 1.
en | Connection 5.8 AUTODOME 5000 Analog PTZ Camera Prepare the Camera for Assembly The camera is shipped with a PE cloth sheet covering the inside the dome cover and a lens cap attached to the lens. Follow the steps below to remove them. 5.9 1. Loosen the screws from the top of the Dome Cover. 2. Rotate and detach the Dome Cover from the Dome Camera Body. 3. Remove the PE cloth sheet and take off the lens cap.
AUTODOME 5000 Analog PTZ Camera 5.10 Connection | en 21 Assemble the Outdoor Camera Refer to the following illustration and descriptions for the assembly of the Outdoor Dome Camera. 1 2 3 4 5 6 7 1 M5x8L Mechanical Screw with Spring 4 Sunshield Washer (1 piece) 2 Outdoor Adaptor 5 Camera Body 3 M4x21L Mechanical Screw with Spring 6 Bubble Washer (3 pieces) 7 M3x23L Screws with Rubber (2 pieces) Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.
en | Connection AUTODOME 5000 Analog PTZ Camera Assembly Instructions 1. Attach the Bubble (6) to the Camera Body (5) and fasten the two M3x23L screws (7). 2. Attach the Sunshield (4) to the Camera Body (5) by fastening the three (3) M4x21L screws. 3. Attach the Outdoor Adaptor (2) to the Camera Body (5) by turning clockwise and fasten the M5x8L screw (1) after all cables are connected to the camera back plate.
AUTODOME 5000 Analog PTZ Camera Connection | en 23 Notice! Use of Grounded Conduit A grounded conduit is required in order to meet the EMC Regulation Requirements. Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.
en | On-Screen Display (OSD) Menu 6 AUTODOME 5000 Analog PTZ Camera On-Screen Display (OSD) Menu The On-screen Display Setup Menu provides access to all programmable settings for the camera. Note: Although not always identified in the table below, most of the submenus have an Exit option as well. 6.
AUTODOME 5000 Analog PTZ Camera SUBMENU 1 On-Screen Display (OSD) Menu | en SUBMENU 2 Night Mode Enhancement DNR SUBMENU 3 25 VALUE Auto, On, Off Zoom, Stabilize, Off 2D N.R. On, Off 3D N.R. On, Off Restore Defaults Exit Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.
en | On-Screen Display (OSD) Menu 6.2 AUTODOME 5000 Analog PTZ Camera Lens Setup Menu SUBMENU 1 SUBMENU 2 Auto Focus SUBMENU 3 VALUE Constant Manual Spot Digital Zoom <2x> to <12x> Restore Defaults Exit 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
AUTODOME 5000 Analog PTZ Camera 6.3 On-Screen Display (OSD) Menu | en 27 PTZ Setup Menu SUBMENU 1 SUBMENU 2 SUBMENU 3 VALUE Autopan Autopan <1> to <4> Start Point PT Move, To Save End Point PT Move, To Save Direction Right, Left Speed <9°/sec>, <16°/sec>, <21°/sec>, <32°/sec> Dwell Time <000> to <127>, Always Tour Preset Tour Preset Run Autopan Enter Tour <1> to <8> Record Start Enter Record Ent Enter Run Tour Enter P. Tour <1> to <8> P.
en | On-Screen Display (OSD) Menu SUBMENU 1 AUTODOME 5000 Analog PTZ Camera SUBMENU 2 SUBMENU 3 Return Time VALUE <005> to <099> sec. or <2>, <3>, <4>, <5> min. Schedule Switch On, Off Point <1> to <32> Hour <0> to <23> Minute <0> to <59> Mode None, Preset, P.
AUTODOME 5000 Analog PTZ Camera 6.
en | On-Screen Display (OSD) Menu 6.5 AUTODOME 5000 Analog PTZ Camera Alarm Setup Menu SUBMENU 1 SUBMENU 2 SUBMENU 3 VALUE Alarm Setting Alarm Pin <01> to <04> Alarm Switch On, Off Alarm Type (NORMAL OPEN), (NORMAL CLOSE) Alarm Action Preset, Preset Tour, Autopan, Tour Preset Point <01> to <99> P. Tour <01> to <08> Autopan <01> to <04> Tour <01> to <08> Dwell Time Always, <001> to <127> (Sec.
AUTODOME 5000 Analog PTZ Camera 6.6 On-Screen Display (OSD) Menu | en 31 Language Setup Menu SUBMENU 1 SUBMENU 2 SUBMENU 3 VALUE EN DE FR ES NL IT PL PT RU ZH-ZN Exit Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.
en | On-Screen Display (OSD) Menu 6.7 AUTODOME 5000 Analog PTZ Camera Installer Menu SUBMENU 1 SUBMENU 2 System Setup System Reset SUBMENU 3 VALUE System Reset Initialize Camera Password On, Off Image Inverse On, Off Flip Off, M.E., Image OSD Auto Close Off, <10>, <15>, <20>, <25>, <30>, <60>, <90>, <120> sec. Camera Setting ID Setting Setting Type HW, OSD ID Number <01> to <99> Title Setting Enter Protocol OSRD, Pelco P, Pelco D Baud Rate <2400>, <4800>, <9600> ID Info.
AUTODOME 5000 Analog PTZ Camera On-Screen Display (OSD) Menu | en 33 Monitor Display 6.8 The information shown on the screen is classified in terms of displaying position, function, OSD display and description, as shown in the table below.
en | On-Screen Display (OSD) Menu Position Function 9 AUTODOME 5000 Analog PTZ Camera OSD Display Description Time XXXX/XX/XX XX:XX Position display XX YYY/YY 10 Year/Month/Day Hour: Minute XX: facing direction of PTZ (N, E, Z, W, NE, SE, SW, SN) YYY/YY: angle of PZT, 0 ~ 359 / 10 ~ −90 When the camera is starting up, the OSD Start Page will display information including ID number, protocol / baud rate, and camera initializing message.
AUTODOME 5000 Analog PTZ Camera 6.9 On-Screen Display (OSD) Menu | en 35 Main Menu When you use Pelco-D and Pelco-P protocol with your controller, you can access the MAIN MENU on your monitor by pressing the keys [95] + [Preset], or by pressing and holding the [Menu] key for 2 seconds. When you use Bosch OSRD protocol with your controller, you can access the MAIN MENU on your monitor by pressing the keys [ON]+[46]+[Enter].
en | On-Screen Display (OSD) Menu 6.9.1 AUTODOME 5000 Analog PTZ Camera Common Menus Exit Exit the menu. Restore Defaults The RESTORE DEFAULTS menu is for restoring the settings in any of the menus to the factory default values. Select to reset the parameters. 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
AUTODOME 5000 Analog PTZ Camera 6.10 On-Screen Display (OSD) Menu | en 37 Camera Setup The Camera Setup menu is as shown below: CAMERA SETUP WHITE BALANCE VIDEO LEVEL AUTO SENSUP MAX EXPOSURE MODE BACKLIGHT SHARPNESS WDR FUNCTION NIGHT MODE ENHANCEMENT DNR RESTORE DEFAULTS EXIT 6.10.1 White Balance A digital camera needs to find reference to color temperature, which is a way of measuring the quality of a light source, for calculating all the other colors.
en | On-Screen Display (OSD) Menu AUTODOME 5000 Analog PTZ Camera ATW In Auto Tracking White Balance (ATW) mode, the camera takes out the signals in a screen in the range from 2000 K to 10,000 K. Manual In this mode, you can change the White Balance value manually. R Gain and B Gain are adjustable and range from <000> to <127>. MANUAL 6.10.2 R Gain 010 B Gain 019 Exit + Save YES Video Level Adjust the video level from <1> to <15> (−10.5 dB to 10.5 dB). Select to disable the function. 6.
AUTODOME 5000 Analog PTZ Camera 6.10.5 On-Screen Display (OSD) Menu | en 39 Backlight The backlight compensation function helps to improves image quality when the background illumination level is high. Select to activate the function. The center object will be brightened in contrast to the edge of the picture (where a backlight would be most likely located). 6.10.6 Sharpness In this menu, you can adjust enhancement of the edges of objects in the picture.
en | On-Screen Display (OSD) Menu AUTODOME 5000 Analog PTZ Camera With 2D / 3D Digital Noise Reduction (D.N.R.), the processor analyzes pixel by pixel and frame by frame to eliminate environmental noise signal so that the highest quality image can be produced even in low light conditions. In comparison with 2D D.N.R., 3D D.N.R. generates better de-noising effects. 6.11 Lens Setup The Lens Setup menu is as shown below. LENS SETUP AUTO FOCUS DIGITAL ZOOM RESTORE DEFAULTS EXIT 6.11.
AUTODOME 5000 Analog PTZ Camera On-Screen Display (OSD) Menu | en 41 PTZ SETUP HOME SETTING SCHEDULE MISC FUNCTION RESTORE DEFAULTS EXIT 6.12.1 Autopan Autopan means the motion of scanning an area horizontally so that the camera can catch the horizontal view. The parameters are as follows. AUTOPAN Autopan 01 Start Point PT Move End Point PT Move Direction Right Speed 9° sec. Dwell Time 001 Run Autopan Enter Exit YES Autopan There are four sets of Autopan Lines built into the camera.
en | On-Screen Display (OSD) Menu AUTODOME 5000 Analog PTZ Camera 1 Camera 2 LEFT (counterclockwise) selection 3 RIGHT (clockwise) selection 4 Start point 5 End point Speed You can define the rotation speed during Autopan. The speed is adjustable from 9°/sec., 16°/ sec, 21°/sec. or 32°/sec. Dwell Time The dwell time is the duration of time that the camera remain at an Autopan line, and the range is from <000> to <127> seconds.
AUTODOME 5000 Analog PTZ Camera On-Screen Display (OSD) Menu | en 43 TOUR Run Tour Enter Exit YES Tour Up to eight sets of Tour routes can be created for one camera. Use the LEFT/RIGHT direction keys to select a set first and then follow the steps below to start recording the Tour route. Record Start Follow the description below to record the TOUR route. 1.
en | On-Screen Display (OSD) Menu AUTODOME 5000 Analog PTZ Camera Preset Tour Point Up to 64 points can be setup for each Preset Tour. The Preset Tour Points represent order of the preset points that the camera will run automatically. The following setup items, including PRESET POSITION, SPEED and DWELL TIME influence how the camera runs through each preset tour point. Preset Position Assign a specific preset position to the selected Preset Tour Point . Options include <1> to <99> and .
AUTODOME 5000 Analog PTZ Camera On-Screen Display (OSD) Menu | en 45 Preset Set A total of 99 preset points can be set. Follow the steps below. 1. Press the LEFT/RIGHT direction keys to select a number (01 represents preset point 1, 02 represents preset point 2, etc.). 2. Press the key and then move the camera to a targeted shooting area/ point. 3. Press the key again to save the defined preset point. 4.
en | On-Screen Display (OSD) Menu 6.12.5 AUTODOME 5000 Analog PTZ Camera Freeze Freeze function allows you to hold the image while the camera is moving between preset positions such as in PRESET and PRESET TOUR modes. For example, when the camera is manipulated to run from point A to point B, if the Freeze function is activated, the first view that you would see is point A. Then the next view would directly change to point B without displaying the moving path. 6.12.
AUTODOME 5000 Analog PTZ Camera On-Screen Display (OSD) Menu | en 47 Return Time The camera starts to count down RETURN TIME when the dome idles, and then execute the SELECT MODE function when the return time is up. The RETURN TIME ranges from 5 to 99 seconds or 2, 3, 4, or 5 minutes. Go If the HOME function is enabled, select this parameter to execute the HOME. 6.12.
en | On-Screen Display (OSD) Menu AUTODOME 5000 Analog PTZ Camera Mode Line After you select a schedule function for MODE, you can specify the MODE LINE of the selected schedule function. According to different schedule functions, options for MODE LINE will be different. Schedule Reset You can reset the whole schedule setting with this item. 6.12.8 Misc. Function You can set up some miscellaneous functions here. MISC FUNCTION Angle Adjuster Enter PT Position Enter Speed By Zoom Off Auto Cali.
AUTODOME 5000 Analog PTZ Camera On-Screen Display (OSD) Menu | en 49 DISPLAY SETUP ID DISPLAY TITLE DISPLAY PRIVACY MASKING TIME SETTING MOTION TRACK RESTORE DEFAULTS EXIT 6.13.1 ID Display You can decide whether the camera’s ID will be displayed on the screen for the purpose of identifying the camera. Select to enable the display of the ID address of the camera on the screen. Alternatively, select to hide the ID address of the camera. 6.13.
en | On-Screen Display (OSD) Menu 5. AUTODOME 5000 Analog PTZ Camera Choose a character with direction keys and then press the key to input. For example: , , . The title is ABC. 6. To delete input characters, move the cursor to or and press to select a character in the entry field. Then move the cursor to and press to delete the selected character. 7.
AUTODOME 5000 Analog PTZ Camera On-Screen Display (OSD) Menu | en 51 Transparency The privacy masks can be set as transparent. Select to display transparent masks. Color Colors of privacy masks can be set via this item. The available colors are black, white, red, green, blue, cyan, yellow and magenta. Set Masking Use the control device to move the camera to the area where you want to set a mask. Press to enter the SET MASK menu.
en | On-Screen Display (OSD) Menu 6.13.5 AUTODOME 5000 Analog PTZ Camera Motion Track Motion Track consists of algorithms that detect movements or changes to see whether the movements or changes mean a possible threat is about to occur or is occurring. These algorithms work by examining each pixel of the video and putting together all the pixel changes. If many pixels are changing in one area and that area is moving in a direction, the software considers this to be a motion.
AUTODOME 5000 Analog PTZ Camera On-Screen Display (OSD) Menu | en 53 ALARM SETTING Alarm Pin 01 Alarm Switch OFF Alarm Type NO Alarm Action Preset Preset Point 01 Dwell Time 003 Sec Alarm Priority 1 Alarm Output 1+2 Exit Yes Alarm Pin The camera supports up to four sets of alarm inputs. Select an alarm input pin number to setup its related parameters. For pin definitions of the alarm connector, refer to the section Alarm Type.
en | On-Screen Display (OSD) Menu AUTODOME 5000 Analog PTZ Camera Figure 6.1: Alarm Type 1 Normally Open 2 Normally Closed 3 Alarm Alarm Action The alarm actions include PRESET, PRESET TOUR, AUTOPAN and TOUR functions. Select one of these modes so that the action will be executed when the selected alarm pin is triggered. The items listed below will change in accordance with the selected alarm action.
AUTODOME 5000 Analog PTZ Camera On-Screen Display (OSD) Menu | en 55 Autopan Select an Auto Pan line that the camera should execute when the alarm pin is triggered. The Auto Pan line(s) should be defined prior either in the AUTOPAN setup menu or through the keyboard. Tour Select a tour line that the camera should execute when the alarm pin is triggered. The tour line(s) should be defined prior either in the TOUR setup menu or through the keyboard.
en | On-Screen Display (OSD) Menu AUTODOME 5000 Analog PTZ Camera Block Mode Select to enable highlighting of detected motion in the monitoring area. Select to disable highlighting of detected motion. Frame Set You can define specific areas as motion detection target zones. Refer to the instructions as follows to configure parameters for each motion detection zone so-called “Frame.” A total of four frames can be set.
AUTODOME 5000 Analog PTZ Camera On-Screen Display (OSD) Menu | en 57 Notice! The dwell time is only adjustable when PRESET is selected as the alarm action. When the dwell time is up, the camera will go back to its triggered position and recheck alarm pin status. Frame Disable Select a frame to be canceled, and press . The selected frame will then be removed. Threshold The Threshold range is adjustable from <1> to <255>.
en | On-Screen Display (OSD) Menu – AUTODOME 5000 Analog PTZ Camera System Reset Select this function for system reboot. Press and system reboot will be initiated. – Initialize Camera This function allows users to restore the camera to its factory default state. Press and the camera will start to retrieve the factory default setting. Password In this menu, you can set the password for OSD control.
AUTODOME 5000 Analog PTZ Camera On-Screen Display (OSD) Menu | en 59 Application: You can see the displayed images, as shown below, when a dome is placed on the desk top in a conference, for instance. Image Inverse OFF Image Inverse ON Notice! When the Image Inverse function is enabled, the Privacy Masking function will be disabled automatically. Refer to the section Image Inverse Off. Flip This function allows the camera to track an object continuously when it passes through the camera’s view.
en | On-Screen Display (OSD) Menu AUTODOME 5000 Analog PTZ Camera Notice! To make the camera tilt between a specific range (−10° to 100°), refer to the section Angle Adjuster to set the angle range of tilt movement. Otherwise, the camera will tilt 90° as the default setting. OSD Auto Close Specifies the duration that the OSD menu appears on the screen, in seconds: 10, 15, 20, 25, 30, 60, 90, and 120. To keep the OSD menu on the screen without auto exit, set this option to . 6.16.
AUTODOME 5000 Analog PTZ Camera On-Screen Display (OSD) Menu | en 61 Select the correct baud rate: 2400, 4800, and 9600 ID Info. Displays the information about the camera ID, ID number, title, protocol, and baud rate. ID INFO. ID Number 001 Title ABC Protocol OSRD Baud Rate 9600BPS Exit YES Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.
en | Operation 7 AUTODOME 5000 Analog PTZ Camera Operation The following tables identify common Aux commands (hot keys) for Bosch protocol and for Pelco protocol.
AUTODOME 5000 Analog PTZ Camera Preset Command / Operation | en 63 Key Description Example Set Restores all settings to original defaults and Set+899+Enter Function Restores all settings clears all user-programmed settings Autopan left limit Set Save AutoPan left limit Set+101+Enter Set Save AutoPan right limit Set+102+Enter ( = manual preset) Autopan right limit ( = manual preset) Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.
en | Operation AUTODOME 5000 Analog PTZ Camera Hot Keys, Pelco Protocol Preset Key Preset Operation Example Number Preset Preset 1-59,101-140 No. + Preset 1+ Preset Preset shortcut saving *Preset 1-59,101-140 * * Scan Setup Preset 60 No. + Preset 60+Preset Scan Setup Preset / Scan 61-68 No. + Preset 61+Preset 1+Scan Preset Tour Setup Preset 70 No. + Preset 70+Preset Run Preset Tour #1 Preset / Tour 71 No. + Preset 71+Preset Run Preset Tour #2 Preset / Tour 72 No.
AUTODOME 5000 Analog PTZ Camera Preset Operation | en Key Preset Operation Example 65 Number D.Zoom ( toggle) Preset 97 No. + Preset 97+Preset Run Autopan #1 Preset 99 No. + Preset 99+Preset Bosch Security Systems, Inc. Operations Manual 2013.07 | 1.
en | Troubleshooting 8 AUTODOME 5000 Analog PTZ Camera Troubleshooting If problems occur, check the installation of the camera with the instructions in this manual. Refer to this guide for further information. Problem Solution No video on screen. - Verify that the power is connected to all components in the system. - Verify that the power switch is ON. - Verify the status of cables or the connection of cables. Poor video quality.
AUTODOME 5000 Analog PTZ Camera Troubleshooting | en 67 Problem Solution The camera has 20 Motion Detection function is enabled. Only 16 zones can be displayed Privacy Masking when this function is enabled. zones, but I can only set 16. I set Image Flip Privacy Masking function is enabled. When this function is enabled, function, but it is Image Flip function is disabled. Both functions cannot be enabled at disabled. the same time. I set Image Inverse Privacy Masking function is enabled.
en | Technical data 9 AUTODOME 5000 Analog PTZ Camera Technical data 295.5 (11.63) 218.38 (8.6) 81.9 (3.22) Camera Dimensions mm (in.) 208 (8.19) 187 (7.36) Figure 9.1: AUTODOME 5000 Indoor/Outdoor Dimensions 1 Diameter without sunshield (indoor models) 2 Diameter with sunshield (outdoor models) 2013.07 | 1.3 | Operations Manual Bosch Security Systems, Inc.
AUTODOME 5000 Analog PTZ Camera 10 Appendices | en 69 Appendices The following tables list the DIP Switch settings for camera IDs.
en | Appendices AUTODOME 5000 Analog PTZ Camera ID Number 2013.07 | 1.
AUTODOME 5000 Analog PTZ Camera ID Number Appendices | en SW-1 SW-2 SW-3 SW-4 SW-5 SW-6 SW-7 SW-8 Sw-9 SW-10 64 OFF OFF OFF OFF OFF OFF ON OFF OFF OFF 65 ON OFF OFF OFF OFF OFF ON OFF OFF OFF 66 OFF ON OFF OFF OFF OFF ON OFF OFF OFF 67 ON ON OFF OFF OFF OFF ON OFF OFF OFF 68 OFF OFF ON OFF OFF OFF ON OFF OFF OFF 69 ON OFF ON OFF OFF OFF ON OFF OFF OFF 70 OFF ON ON OFF OFF OFF ON OFF OFF OFF 71 ON ON ON OFF OFF OF
en | Appendices AUTODOME 5000 Analog PTZ Camera ID Number SW-1 SW-2 SW-3 SW-4 SW-5 SW-6 SW-7 SW-8 Sw-9 SW-10 97 ON OFF OFF OFF OFF ON ON OFF OFF OFF 98 OFF ON OFF OFF OFF ON ON OFF OFF OFF 99 ON ON OFF OFF OFF ON ON OFF OFF OFF Table 10.
Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, PA, 17601 USA www.boschsecurity.com © Bosch Security Systems, Inc.
