Flush Mount Ceiling Kit VDA-NWDFMT | VDA-NWDSKT en Mounting Guide
Flush Mount Ceiling Kit Table of Contents | en iii Table of Contents 1 Unpacking 1 1.1 Parts List 1 1.2 Safety Rules 3 2 Installing the Recessed Camera Mount 4 2.1 Installing the VDA-NWDSKT Bracket 5 2.2 Mounting the FlexiDome IP Camera 2.3 Mounting the AutoDome Analog/IP Camera Bosch Security Systems, Inc. Mounting Guide 6 12 F.01U.126.944 | 1.0 | 2009.
iv en | Table of Contents F.01U.126.944 | 1.0 | 2009.04 Flush Mount Ceiling Kit Mounting Guide Bosch Security Systems, Inc.
Flush Mount Ceiling Kit 1 Unpacking | en 1 Unpacking Unpack this equipment and handle with care. If an item appears to have been damaged in shipment, notify the shipper immediately. Verify that all the parts listed in the section below are included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative. The original packing carton is the safest container in which to transport the unit and must be used if returning the unit for service.
2 en | Unpacking Flush Mount Ceiling Kit The illustration below shows a typical installation: Figure 1.1 1 2 3 4 Typical VDA-NWDFMT installation Drywall ceiling or ceiling tile, 6–23 mm (.24–.91 in.) thick Recess bracket with backplate FlexiDome IP or AutoDome Easy Analog/IP camera Recess trim ring F.01U.126.944 | 1.0 | 2009.04 Mounting Guide Bosch Security Systems, Inc.
Flush Mount Ceiling Kit 1.2 Unpacking | en 3 Safety Rules To ensure safety, the following warnings are specified: – The device must be installed and maintained by skilled technical personnel. – Connect the device to a power source corresponding to the indications given on the marking label. – Use only the attachments/accessories specified by the manufacturer. – Do not use the device near water. – Do not use the device in the presence of flammable substances.
4 en | Installing the Recessed Camera Mount 2 Flush Mount Ceiling Kit Installing the Recessed Camera Mount Use this mount to install a FlexiDome IP (NWD-4xx) camera or an AutoDome Easy Analog or IP (VEZ series) camera. The VDANWDFMT can be secured to a ceiling tile or to a drywall ceiling. The ceiling must be between 6–23 mm (.24–.91 in.) thick and be able to support the combined weight of the camera and the Flush Mount Ceiling kit.
Flush Mount Ceiling Kit 2.1 Installing the Recessed Camera Mount | en 5 Installing the VDA-NWDSKT Bracket The VDA-NWDSKT is a support bracket for the VDA-NWDFMT Flush Mount Ceiling kit. Use this bracket to add support to a ceiling tile. Note: The weight of the VDA-NWDSKT is 1.12 kg (2.46 lb). 1. 2. Remove the ceiling tile. Determine the proper width of the VDA-NWDSKT so that the side tabs rest against the ceiling T-rails. 3.
6 en | Installing the Recessed Camera Mount 2.2 Flush Mount Ceiling Kit Mounting the FlexiDome IP Camera Use the following image as a reference for the following procedure: Figure 2.2 FlexiDome IP components 1 2 3 4 Mounting plate Camera module/base Inner liner Trim ring and dome 1. Determine a secure location for the flush mount ceiling kit. 2. If the ceiling tile is too thin or if it requires extra support, Refer to Table 2.1, Page 4, for weight information. refer to Section 2.
Flush Mount Ceiling Kit 5. Installing the Recessed Camera Mount | en 7 Loosen the three tamper-resistant screws in the FlexiDome IP Trim Ring (the screws remain in place) using a T20 pinin Torx driver. Remove the Trim Ring with Dome (Figure 2.2, item 4) by pulling it off of the base. 6. Remove the Inner Liner (Figure 2.2, item 3) by removing it from the Camera Module/Base. 7. Loosen the three Phillips head screws that secure the Camera Module/Base (Figure 2.
8 en | Installing the Recessed Camera Mount Flush Mount Ceiling Kit 13. Slide the Mounting Plate/Bracket assembly into the cutout in the ceiling tile. You may have to push the support screws from below to engage the toggle bolts. Figure 2.4 Insert recess bracket into ceiling 14. Tighten the support screws (item 6, below) until the toggle bolts grasp the ceiling tile. Do not overtighten the support screws; it may cause the ceiling tile to break. Figure 2.5 F.01U.126.944 | 1.0 | 2009.
Flush Mount Ceiling Kit Installing the Recessed Camera Mount | en 9 15. Attach a suspension wire to the top of the recess bracket at one of the points indicated below and then to a structural element in the ceiling. ! WARNING! You must secure the bracket to a structural ceiling element with a suspension wire to avoid personal injury and damage to the camera. Figure 2.6 Attach suspension wire 16. Connect the cables to the connection box, located inside the Camera Module.
10 en | Installing the Recessed Camera Mount Flush Mount Ceiling Kit 18. Attach one end of the safety tether to the hook on the Mounting Plate and the other end to the hook on the Camera Module/Base. Figure 2.7 7 8 Attach safety tether Safety tether Camera Module/Base 19. Reattach the Camera Module/Base to the Mounting Plate. 20. Push against the underside of the FlexiDome to push the unit and the bracket up into the ceiling. 21. Adjust the focus of the camera to your desired view.
Flush Mount Ceiling Kit Installing the Recessed Camera Mount | en 11 23. Attach the Recess Trim Ring with the three #8-32 x 5/8 in. self-tapping screws. Figure 2.8 Bosch Security Systems, Inc. Attach recess trim ring Mounting Guide F.01U.126.944 | 1.0 | 2009.
12 en | Installing the Recessed Camera Mount 2.3 Flush Mount Ceiling Kit Mounting the AutoDome Analog/IP Camera 1. Determine a secure location for the flush mount ceiling kit. Refer to Table 2.1, Page 4, for weight information. 2. If the ceiling tile is too thin or if it requires extra support, refer to Section 2.1 Installing the VDA-NWDSKT Bracket, Page 5. ! WARNING! The ceiling tile or the drywall must be between 6–23 mm (.24–.91 in.) thick. 3.
Flush Mount Ceiling Kit 6. Installing the Recessed Camera Mount | en 13 Route the wires from the AutoDome Easy through the slot in the Recess bracket. 7. Align the three holes on the top of the AutoDome Easy with the three small holes on the Recess Bracket (item 2, below). Figure 2.10 8. Attach AutoDome Easy to backplate Secure the AutoDome Easy to the Recessed Bracket using the three M2.5 x 8 mm Phillips Head screws. 9.
14 en | Installing the Recessed Camera Mount Flush Mount Ceiling Kit 12. Slide the AutoDome Easy Bracket assembly into the cutout in the ceiling tile. You may have to push the support screws from below to engage the toggle bolts. Figure 2.11 Insert recess bracket/camera assembly into ceiling 13. Tighten the support screws (item 3, below) until the toggle bolts grasp the ceiling. Do not overtighten the support screws; it may cause the ceiling tile to break. Figure 2.12 F.01U.126.944 | 1.0 | 2009.
Flush Mount Ceiling Kit Installing the Recessed Camera Mount | en 15 14. Attach a suspension wire to the top of the recess bracket at one of the points indicated below and then to a structural element in the ceiling. ! WARNING! You must secure the bracket to a structural ceiling element with a suspension wire to avoid personal injury and damage to the camera. Figure 2.13 Attach suspension wire 15. Push against the underside of the AutoDome Easy to push the unit and the bracket up into the ceiling.
16 en | Installing the Recessed Camera Mount Flush Mount Ceiling Kit 16. Attach the Recess Trim Ring with the three #8-32 x 5/8 in. self-tapping screws. Figure 2.14 Attach recess trim ring F.01U.126.944 | 1.0 | 2009.04 Mounting Guide Bosch Security Systems, Inc.
Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, PA 17601 USA Telephone +1 800 289 0096 Fax +1 585 223 9180 www.boschsecurity.com © 2009 Bosch Security Systems, Inc.; F.01U.126.944 | 1.0 | 2009.04; Data subject to change.
