Owners Manual
Table Of Contents
- How This Manual Is Organized
- Safety
- Proper Installation and Maintenance
- Fire Safety
- Burn Prevention
- Child Safety
- Cleaning Safety
- Cookware Safety
- Food Safety
- Getting Started
- Parts and Accessories
- Radiant Elements
- Single Element
- Double Element (some models)
- The dual element consists of two (a small and a large) radiant element within the same heating area. Either the small element, or both elements may be selected for use.
- Triple Element (some models)
- Power Element (some models)
- Warming Zone
- Retained Heat
- Temperature Limiter
- Hot Surface Indicator
- Convection Fan
- Oven Vent
- Automatic Shutoff
- Self-Cleaning
- Indicators and Other Features
- Standby Mode
- Accessories
- Inserting Racks
- Flat Rack
- To insert the flat rack into the oven:
- 1. Grasp rack firmly on both sides.
- 2. Insert rack (see picture).
- 3. Tilt rack up (A) to allow the upwardly sloped rear of the rack to slide under the stop molded into the front portion of the rack guide above.
- 4. When the back of the rack is past this stop, lower the front of the rack to a horizontal position (B) and push it the rest of the way in.
- To remove the flat rack from the oven:
- Telescopic Rack (some models)
- To insert the telescopic rack into the oven:
- 1. Slide the rack in evenly until the rear of the rack is about 2 inches from the back of the oven.
- 2. Tilt the front of the rack up about 3/4’s of an inch (A) and finish pushing the rack all the way back (B)
- 3. The back of the telescopic rack drops into place.
- 4. Pull the rack forward to engage the bottom of the rack onto the rear of the rack position guide.
- 5. Lower the front of the rack to finish seating it on the rack guide. The rack should feel stable when properly seated.
- 6. Slide the movable part of the telescopic rack in and out a few times to make sure it is able to move freely and that the non-moving part of the telescopic rack is securely anchored.
- To remove the telescopic rack from the oven:
- Accessories
- Before Using the Appliance for the First Time
- Operation - Cooktop
- Setting the Element Heat Level
- Single Element Control Knob
- Double Element Control Knob
- Power Element Control Knob (some models)
- Triple Element Control Knob (some models)
- Warming Zone
- Surface Element On/Hot Indicators
- Cooktops with a triple front element
- Cooktops with a double front element
- Surface Elements Disabled During Self Clean
- Operation - Oven
- Oven Control Panel
- Setting the Clock
- To set the clock
- 1. The oven must be in Standby mode (oven is powered on, but no cooking mode or timer in operation).
- 2. To access the clock set mode:
- 3. Use the numeric keypad to enter the desired time. Each number pressed is entered at the right and moving previously entered digits to the left. To set “12:45 pm”, press 1, 2, 4, 5.
- 4. When the desired time is entered, set the time by pressing Enter.
- To set the clock
- Setting the Cooking Mode and Temperature
- 1. Press the desired Cooking Mode button. The cooking mode and default temperature are displayed. The temperature flashes to show it can be edited.
- 2. Press Enter to start the mode using the default temperature.
- 3. To change the temperature, enter the new temperature using the numeric buttons. 375° is used for this example. Press Enter to set the updated temperature.
- 4. Preheating starts.
- 1. Press the numeric keys to enter the desired temperature setting. The temperature entered is displayed beside the current time.
- 2. Select a cooking mode that is compatible with the temperature entered. If no cooking mode is selected within 5 seconds of setting the temperature, an error tone sounds and a SELECT MODE message is displayed and blinks.
- 3. Press a Mode Selection button to select a cooking mode.
- 1. Press the Cooking Mode button.
- 2. The current temperature flashes. Use the numeric buttons to enter a new temperature. Press Enter.
- Timer
- To set a kitchen timer
- Cancel the kitchen timer - by pressing the Kitchen Timer On/Off button.
- Note
- To edit a kitchen timer
- To set an oven timer
- 1. Press the Oven Timer button.
- 2. Select mode, press Enter.
- 3. When the timer reaches :00 the cooking mode ends and the message “OVEN TIMER FINISHED” is displayed. The oven alarm tone sounds every 10 seconds for 2 minutes.
- 1. If the oven timer is running and the time remaining needs to be changed, enter the oven timer mode by pressing the Oven Timer button.
- 2. The temperature blinks, indicating it can be edited. Input a new temperature or press Enter for no change.
- 3. The timer value blinks, indicating it can be edited. Input the new time and restart the timer by pressing the Enter button.
- Fast Preheat
- Probe (some models)
- 1. Insert the probe into the meat as described above. The probe symbol is displayed.
- 2. Connect the probe to the oven. If the probe is not connected to the oven prior to starting Probe mode, an error tone sounds and the message “INSERT PROBE” is displayed.
- 3. Set the cooking mode and temperature.
- 4. The Set Probe Temp screen is displayed. A three digit input prompt “- - -” blinks in the lower right corner. Use the numeric keypad to enter the desired probe temperature and press Enter.
- 5. The probe current temperature and target temperature are both displayed in the format “105 / 180” at the lower right corner of the display. The actual temperature will display < 80 until the food temperature reaches 80° F.
- 6. When the probe temperature reaches the set temperature, the cooking mode turns off. The current time is displayed and the message “COOKING COMPLETE” blinks at the bottom left of the display. An alarm tone sounds every 10 seconds for 2 minutes.
- Note:
- Sabbath Mode
- 1. Begin a Bake operation. While Bake is running, press and hold the Oven Timer button for five seconds.
- 2. Press Enter to accept the default 74:00 hours and start Sabbath Mode, or use the numeric keypad to enter the desired Sabbath Mode timer value. Timer values between 0:01 and 74:00 can be entered.
- 3. Once Sabbath Mode has begun, the display changes to show the message “SABBATH ON”.
- 4. After the Sabbath Mode countdown reaches zero, the oven displays the current time and the message “SABBATH”. No changes can be made at this point. To end the Sabbath Mode and return to normal function, press the Oven Clear/Off button.
- Note:
- Panel Lock
- Sabbath Mode
- 1. Press the Settings button.
- 2. The first setup item is displayed. The display shows “SET CLOCK”. Press Settings again to access the settings menu.
- 3. To display a different setup item, press the number corresponding to that setting (see table following or press the Settings button to cycle through available options).
- 4. To change the value for the displayed setting press the Enter button to enter the edit mode. Use the numeric keypad to change the setting value. The corresponding setting value is shown in the table following.
- Oven Temperature Offset
- Settings Menu Options
- Operation - Warming Drawer
- About the Warming Drawer
- Operation
- Preheating
- Turning Warming Drawer On and Off
- 1. Press the Warming Drawer button.
- 2. “WARMING DRAWER” will be displayed with the default setting “MED”. The warming drawer amber icon is displayed below the clock.
- 3. To accept the “MED” setting, press Enter. The setting is accepted and the warming drawer icon remains illuminated. If enter is not pressed, the warming drawer setting is not accepted and the warming drawer turns off.
- 4. To change the setting, when “MED” is displayed, press the Warming Drawer button again. The setting changes to “HIGH”. Press the Warming Drawer button again to change the setting to “LOW”. To accept a setting, press Enter. The displayed...
- 5. To turn the warming drawer off, press the Warming Drawer button and the warming drawer will turn off. The warming drawer icon will no longer appear under the clock.
- Warming Empty Serving Bowls and Plates
- Cooktop Cooking Guide
- Cookware Selection Guide
- General Tips
- Care and Cleaning
- Cleaning the Cooktop
- Precautions for Long Life and Good Appearance of the Surface
- Before Use Care
- Daily Cleaning Techniques
- 1. Clean the surface when completely cool with the glass ceramic cooktop cleaner. Exception: Remove dry sugar, sugar syrup, tomato products and milk immediately with the razor blade scraper (See Cooktop Care Chart, next page).
- 2. Wipe off spatters with a clean, damp sponge or paper towel. Rinse and dry. Use white vinegar if smudge remains; rinse.
- 3. Apply a small amount of the glass ceramic cooktop cleaner. When dry, buff surface with a clean paper towel or cloth.
- Using the Razor Blade Scraper
- Cleaning the Control Knobs
- Do Not Use the Following Cleaners
- Cooktop Care Chart
- Cleaning the Oven
- Self Clean
- NOTICE:
- To set the Self Clean mode
- 1. Remove all accessories and racks from the oven.
- 2. If there is a cooking mode on, press Oven Clear/Off to end the running mode.
- 3. Press the Self Clean button below the display.
- 4. When the desired Self Clean time is displayed, press Enter.
- 5. Self Clean starts and the oven Self Clean timer begins its countdown.
- To Cancel Self Clean
- 6. When the cool down is complete, the message “SELF CLEAN FINISHED” is displayed. Continue to use caution when opening the oven door.
- 7. Press Oven Clear/Off to clear the display when Self Clean is finished.
- 8. After the oven has cooled down and the door is unlocked, wipe remaining ash from the oven using a moist cloth.
- Note:
- To set the Self Clean mode
- NOTICE:
- Avoid These Cleaners
- Oven Cleaning Guide
- Cooktop Maintenance
- Glass Ceramic Cooktop Models
- Oven Maintenance
- Replacing an Oven Light
- To change the bulb
- 1. Turn off power to the oven at the main power supply (fuse or breaker box).
- 2. Remove the glass cover by unscrewing it. Turn the glass counterclockwise to remove it.
- 3. Remove the bulb. The bulb unscrews counterclockwise.
- 4. Grasp the new bulb with a clean, dry cloth to prevent depositing skin oils on the glass which could lead to premature bulb failure. Replace the bulb by screwing it in turning the bulb clockwise.
- 5. Screw the glass cover back on.
- 6. Turn power back on at the main power supply (fuse or breaker box).
- To change the bulb
- Removing the Oven Door
- 1. Open the oven door to its fully open, horizontal position.
- 2. Flip levers on hinges toward you.
- Note: It may be necessary to use a tool, such as a screwdriver, to gently pry the upper part of the lever away from the housing. Take care to avoid scratching the housing.
- 3. Bring both door hinge levers to their fullest down position as shown in the illustration. The left and right door hinges may differ slightly but operate in the same manner.
- 4. Close the oven door until it catches on the hinge stop levers, locking the hinges at the proper angle for door removal. The door will be open about 7 inches at the top. This takes the spring tension off the hinges so the door can be easily lifted out
- 5. The door is heavy. Use both hands to firmly grip it by the sides. Do not grip the door by the handle. Maintaining the door angle, lift the door straight up approximately 3/4" to unhook the hinges from the slots and then pull it out towards you unt...
- 6. Place the door in a convenient and stable location for cleaning.
- To replace the oven door
- 1. Holding the door firmly in both hands, grip it on either side, not by the handle.
- 2. Tilt the door back slightly towards you until it opens about 7" at the top.
- 3. Slide the hinges into the slots as far as they will go and then lower the door straight down. The angle of the door may need to be adjusted slightly to allow the hinges to engage properly and the door to lower into place. The door should lower abo...
- 4. Once both hinges are fully engaged as described in Step 3, gently open the door until it is fully open.
- 5. Push the levers on both the hinges up and forward until they are locked into the slot, flush with the front of the oven body.
- 6. Close and open door slowly to be sure it is correctly and securely in place.
- Warming Drawer Maintenance
- Removing the Drawer
- Replacing the Drawer
- 1. Be sure housing slides are pushed inside housing.
- 2. Align the drawer rails with the housing slides attached to the drawer housing.
- 3. Firmly push the drawer straight into the drawer housing until the drawer clicks into place. Note: The drawer has a “push-to-open” operation. Pressing the lower center front of the drawer causes the drawer to self-open.
- 4. Open and close drawer to test operation. Note: if the drawer will not close, verify that the rails on the drawer are properly aligned to housing slides and that the rail release levers are properly positioned.
- Service
- How to Obtain Service or Parts
- Product Data Plate
- Glass Ceramic Cooktop Models
- Cleaning the Cooktop
- Self Help
- Leere Seite
- Leere Seite
Français 48
Impossible d'éteindre l'éclairage du four. Vérifier s'il y a obstruction de la porte du four. Vérifier si la charnière est
tordue. Lorsque la fonction Shabbat est activée, l'éclairage du four reste
allumé ou éteint (en fonction de la sélection effectuée pendant l'installation)
pendant toute la durée du mode Shabbat.
Impossible de retirer la lentille de la
lampe.
Il peut y avoir une accumulation de saleté autour de la lentille. Essuyer
avec un chiffon propre et sec avant de retirer le couvercle.
La fonction d'autonettoyage du four
fonctionne mal.
Laisser refroidir le four avant d'exécuter le cycle d'autonettoyage. Toujours
essuyer les saletés et les déversements importants avant d'exécuter le
cycle d'autonettoyage. Si le four est très sale, programmez-le pour une
durée d'autonettoyage de quatre heures. Voir Préparation du four pour
l'autonettoyage.
L'horloge et la minuterie fonctionnent mal. S'assurer que le four est sous tension. Voir les sections Horloge et
Minuterie.
La porcelaine s'ébrèche Lorsque vous retirez et remettez en place les grilles du four, veillez à
toujours les incliner vers le haut et à ne pas forcer pour les introduire dans
le four pour éviter que la porcelaine ne s'ébrèche.
Un « F » et un numéro s'affichent à l'écran
et le panneau de commande émet un
signal sonore.
Ceci est un code d'erreur. Appuyer sur Off (Désactiver) pour effacer l'écran
et mettre fin au signal sonore. Au besoin, réinitialiser le four. Si un code
d'erreur reste affiché et que le signal sonore ne s'arrête pas, notez le code
d'erreur, annuler le four et appeler un technicien en entretien et en
réparation agréé.
Une forte odeur se dégage de la
cuisinière neuve lorsqu'elle est mise sous
tension
Ceci est normal pour une cuisinière neuve et disparaîtra après quelques
utilisations. Actionner le cycle d'autonettoyage éliminera l'odeur plus
rapidement.
Le panneau de commande ne répond pas
lorsqu'une touche est activée
S'assurer que le pavé tactile est propre. Toucher le centre de la touche à
effleurement. Utiliser le plat du doigt.
Le ventilateur fonctionne pendant les
modes de cuisson qui n'utilisent pas le
mode Convection
Sur certains modèles, le ventilateur à convection fonctionne pendant que
l'on fait préchauffer le four pour le mode Cuisson. Ceci est normal.
Les modèles coulissants sont également dotés d'un ventilateur de
refroidissement qui fonctionne pendant chaque mode de cuisson.
De l'air chaud ou de la vapeur
s'échappent de l'évent du four.
Il est normal de voir ou de sentir de la vapeur ou de l'air chaud s'échapper
de l'évent du four. Ne pas obstruer l'évent.
Le ventilateur de refroidissement
fonctionne alors que le four a été éteint
(cuisinières coulissantes uniquement)
Ceci est normal. Lorsque le four aura refroidi et qu'il aura atteint une
température prédéfinie, le ventilateur de refroidissement s'éteint.
La table de cuisson ne fonctionne pas
pendant le cycle autonettoyant
Ceci est normal pour certains modèles. Le fonctionnement sera rétabli une
fois le cycle autonettoyant terminé.
Problème concernant le four Causes possibles et solutions suggérées