CLASS # 19 5 SPEED WOOD TURNING LATHE This is a completely, self contained wood lathe so there is no maintenance at all. It is manufactured to the highest quality standards and is designed to handle all your wood turning needs. It comes complete with a heavy duty, 3/4 H.P. sealed ball bearing motor, which means it never needs oiling. It has five speeds ranging from 980 rpm to 3000 rpm and there is a full 40" between centers to handle even the big jobs.
CLASS # 19 ANALOG MULTITESTER Manufactured by Sunwa Scientific Instrument Ltd. one of the worlds largest manufacturers of test instruments. The multitester is used to measure electric and electronic components for testing and servicing. This multitester will accurately test AC voltage, and DC voltage. They are DC amperage, transistors & diodes and used by almost any contractor, repairman or industrial tool buyer. The unit is fuse and diode protected for a long service life.
CLASS # 19 ELECTRIC SOLDERING GUN This handy soldering gun is all you need to make quick electrical and connector repairs, either on the job or just around the house. This is a high powered, 100 watt unit that gives you instant heat when you pull the trigger. It includes an extra solder tip and one tube of resin-core solder. There’s even a handy work light built right into the front of the gun that let’s you see while you’re working.
CLASS # 19 1/2” ACE ELECTRIC IMPACT WRENCH These are heavy duty electric impact wrenches that you can take with you anywhere you can plug in a cord. You don’t need an air compressor to quick change your tires or do some of the heavy mechanical work on your vehicles. These wrenches will give you up to 235 ft. Lbs. of adjustable torque and deliver 2,700 blows per minute. They have double insulated 6’ cords and are ergonomically balanced to fit in your hand and reduce fatigue.
CLASS # 19 40 GAL. ELECTRIC PARTS WASHER This is a 40 gallon electric parts washer constructed of heavy duty welded steel with the corrosion resistant finish. Its’ fully enclosed electric pump will re-circulate 20 Liters of solvent per minute. It comes with a heavy duty steel stand complete with a storage shelf and a built in drain. It has a small parts basket and chrome steel flexible spigot and an easy ‘on/off’ switch.
CLASS # 19 20 GAL. ELECTRIC PARTS WASHER This is a 20 gallon electric parts washer constructed of heavy duty welded steel with the corrosion resistant finish. Its’ fully enclosed electric pump will re-circulate 50 gallons of solvent per hour. It comes with a heavy duty steel stand complete with a storage shelf and a built in drain. It has a small parts basket and chrome steel flexible spigot and an easy ‘on/off’ switch.
CLASS # 19 165 AMP AC ARC WELDER This is a 165 Amp, industrial AC ARC Welder from the NEIKO PRO ‘BLUELINE’ series. This is a very rugged, pro-model welder and available at a very affordable price. Lightweight yet durable, it has all the power you need for welding projects in your shop or at home. Comes complete with all the accessories needed to begin working right out of the box. ONE YEAR WARRANTY.
CLASS # 19 160 AMP TIG WELDER This is a professional quality portable welder for TIG, (Tungsten Inert Gas), welding that produces cleaner welds on stainless steel, steel, copper, titanium, and nickel than MIG welding. It’s quick start with high open voltage and 1/4” welding capacity and an easy to use anti-stick circuit for work on rutile, stainless steel, cast iron and basic electrodes. Use as either high accuracy TIG or thick weld MMA arc welder, torches for both are included.
CLASS # 19 3/4 HP ROUTER This is a compact, 3/4 HP router that will make clean, fast cuts on any project. It is lightweight and equipped with a high torque, (23,000 RPM), heavy duty motor for easy routing in any direction. It features contoured handles for comfort and control, and the all ball bearing construction ensures long life and smooth operation. The collet capacity is 3/8” (10mm), the base diameter is 5-7/8"; height 7-1/4"; weight 5.26lbs.
CLASS # 19 3/8” ‘ACE’ REVERSIBLE ELECTRIC DRILL Our new 3/8” drill is like an old friend, you’ll have it around for a long time and it’s always dependable. You get a powerful 4.2 AMP, double insulated, all ball bearing motor. The heavy duty trigger has an easy on-off lock for continuous drilling and there’s a built in belt clip right on the top of the drill housing.
CLASS # 19 3/8” VARIABLE SPEED DRILL The Bosch® 3/8” drill features a best-in-class power-to-weight ratio, which means you get the maximum amount of power with the minimum amount of weight. The 3/8” Jacobs ratcheting chuck holds drill bits exceptionally well for minimal slipping. It has an improved lock-on switch design that prevents accidental lock-on by recessing the switch into the handle and the new soft grip handle provides added comfort. Specifications: ¾ ¾ ¾ ¾ ¾ ¾ ¾ ITEM#: 1006VSR 6.
CLASS # 19 DRYWALL SCREWGUN This factory reconditioned Bosch® drywall screwgun features a compact design for increased comfort and control for all day use. The contoured grip is designed to maximize comfort and minimize fatigue. The Posi-Lok™ nose piece retains depth setting when removed and also eliminates time consuming depth readjustments, while a powerful 101 inch pounds of torque is the best torque ratio in its class. Specifications: • • • • • • • • • • • 4,500 RPM 101 in. lbs.
CLASS # 19 INDUSTRIAL BENCH GRINDERS These new and improved industrial bench grinders are from ‘NEIKO’ and they are sure to get you excited about your grinding jobs again. Not only do they look great…but they act great, too.
CLASS # 19 3” BENCH GRINDER W/ FLEX SHAFT This 3" mini bench grinder is a must for any work bench or hobbyist and features a rugged 110Volt, 60Hz motor that powers up to speed quickly with variable speeds from 0 to 10,000 rpm. It has a built in 31" flex shaft die grinder with an 1/8” mounted grinding stone bit and comes equipped with a 3" grinder stone, a 3" fiber wheel and wrenches. Import. • • • • • • Specifications: Motor: 110 V, 60 Hz.
CLASS # 19 4 1/2” HORIZONTAL METAL BAND SAW This economical, portable, and easy to use, three speed band saw is an excellent choice for small or large projects when you need to cut a variety of metals, plastics, or wood. When the vertical cutting attachment is installed, the saw is able to make vertical cuts for your unique cutting requirements.
CLASS # 19 4 1/2” ELECTRIC DISC GRINDER This grinder is industrial rated, meets all OSHA requirements, and it sets the standard for compact, powerful grinding in the workplace. It features the BOSCH top of the line 7 amp motor that develops 11,000 RPM’s. The side switch operates with either hand and the side handle mounts on the left or the right for user convenience. There is also a push button spindle lock for quick and easy wheel changes.
CLASS # 19 5” ANGLE GRINDER This powerful 10 amp angle grinder has a 5” grinding wheel capacity and a no-load speed of 10,500 rpm. The soft grip auxiliary handle can be used on the left or right side as well as the top of the grinder to adjust for any angle. Includes 1 hex wrench, 1 flange wrench, auxiliary handle, and two extra carbon brushes. Import. UL/CUL approved.
CLASS # 19 7” ELECTRIC POLISHER This 7” polisher features adjustable speed control and all the power needed for tough buffing and polishing jobs on cars, trucks, boats and other vehicles like jet skis, and ATV’s. It has a tough 11 amp motor that spins from 1,000 to 3,000 RPM and an auxiliary side handle for good grip and control. Includes a 7” polisher disc and a 7” wool bonnet. Import.
CLASS # 19 CORDLESS RANDOM ORBITAL SANDER Now you can buff and polish your vehicle without the inconvenience of power cords or air hoses with this 24 volt cordless, random orbital polisher. This powerful cordless tool applies a swirl-free polish to any car, truck, boat or recreation vehicle. Features a top handle for better grip and control, 2800 no load rpm, and 7” hook and loop pad. Includes an 8” SM Arnold™ buffing pad, a 3.5 hour charger, one 1300 mAH Ni-Cd battery and a nylon carry case. Import.
CLASS # 19 1/2” ELECTRIC DRILL This factory reconditioned Skil® drill features a powerful 7.0 amp motor for tough applications as well as a horizontal bubble level for precise drilling and driving. The 1/2” keyed chuck accepts large diameter drill bits that are designed for woodworking or cutting and the variable speed trigger lets user control the drilling speed. Includes chuck key and side handle. Specifications: • • • • • • • • • 7.
CLASS # 19 24 VOLT CORDLESS DRILL This powerful 24 volt cordless drill features dual laser guides for accurate drilling and a heavy duty keyless, 1/2” chuck. It is reversible with 24 torque settings and a no load, variable speed of 0 to 400 rpm on low and 0 to 1,050 rpm on high. Charging time is 3 to 5 hours for the included 24 volt, 1300 mAH battery and there is bubble level at the top of the drill to assist in accurate drilling.
CLASS # 19 1/2” HAMMER DRILL This 1/2” hammer drill features a full size 1/2” chuck and variable speeds from 0 to 3,000 RPM, with adjustable speed hammer blows for drilling into concrete or other masonry. The powerful 600 watt 4.7 amp motor is reversible and the action switch changes easily from hammer drilling to standard drilling. Features include a side assist handle and a depth gauge. Chuck key is included.
CLASS # 19 1/2” HAMMER DRILL This factory reconditioned Bosch® single speed, 1/2” drive hammer drill has a lightweight design which is perfect for small diameter drilling jobs. Its 7 amp motor provides the highest performance to weight ratio in its class. It has a 360° auxiliary handle with a built-in quick release depth gauge for a wide range of movement and consistent drilling depth.
CLASS # 19 1/2” HAMMER DRILL This factory reconditioned Bosch® 1/2” drive hammer drill features an 8.5 amp dual torque motor that can be easily switched between rotation only for 0-3,000 RPM and hammer drill mode for 0-48,000 BPM. It has a 360° auxiliary handle with a built-in quick release depth gauge for a wide range of movement and consistent drilling depth. A patented rotating brush plate extends brush life and provides equal power in reverse.
CLASS # 19 1/2” 2 SPEED HAMMER DRILL This drill features a Bosch-built high output 8.5 Amp variable speed motor and a 1/2” 3-jaw chuck for rugged hammer drilling applications. 2-speeds will handle both wood and metal drilling and the dual selector allows for easy conversion from rotation only mode to hammer drill mode. The patented rotating brush plate provides equal power in reverse to easily back out bound-up bits and double brush life.
CLASS # 19 SDS 1” HAMMER DRILL The Neiko® SDS hammer drill delivers outstanding drilling performance in concrete, brick, block, stucco, drywall and other masonry materials. It has a powerful 6.7 amp motor with a hammer frequency of 0 to 5,800 BPM. Features an SDS (slotted drive system) chuck and three working modes: drill, hammer, and drill with hammer. It is equipped with a depth gauge and an auxiliary front handle and the on/off switch locks on to prevent fatigue.
CLASS # 19 SDS CONCRETE DRILL This factory reconditioned Bosch® concrete drill offers fast and smooth drilling of small diameter holes into concrete and with its compact and lightweight design it is perfect for drilling applications in hard to reach spaces. The 2 mode selector easily converts from rotary hammer to drill only. An integral clutch helps minimize torque reaction and the trigger is variable speed for accurate bit starting as well as for removing fasteners or bound bits from concrete.
CLASS # 19 1/2” 2 SPEED HAMMER DRILL This drill features a Bosch-built high output 8.5 Amp variable speed motor and a 1/2” 3-jaw chuck for rugged hammer drilling applications. 2-speeds will handle both wood and metal drilling and the dual selector allows for easy conversion from rotation only mode to hammer drill mode. The patented rotating brush plate provides equal power in reverse to easily back out bound-up bits and double brush life.
CLASS # 19 16 SPEED DRILL PRESS W/ LASER This is a heavy duty floor model drill press that measures 63” high and features a powerful, 3/4 HP, 120 Volt/550 Watt all ball bearing motor. There are 16 speeds from 210 to 3,670 RPM. The table turns tilts and is fully adjustable up or down. It has a spindle stroke of 3-1/8” and a 1/2” chuck. The spindle is a Morse taper JT-33 that is fully supported by ball bearings.
CLASS # 19 5 SPEED DRILL PRESS W/ LASER GUIDE This is a heavy duty bench top version of the essential drill press and is the safest most reliable way to get precision drilling results. It features a powerful, 1/3 HP, 120 Volt/300 Watt motor for consistent spindle speeds and easy change gearing for variable speeds of 620 to 3,100 RPM. The maximum stroke is 2” and a depth gauge is included.
CLASS # 19 CORDLESS 4-1/2” GRINDER This 24 volt cordless grinder features a high output quick charge battery that reaches full charge in just one hour. It holds any 4-1/2” grinding disc or cutoff wheel and has 7,000 no load RPM, so it’s great for any job. Includes one grinding wheel, one cutoff wheel, an auxiliary side handle that can be attached for either left or right hand use, a 1-hour quick charger, a 16 amp, 24 volt Ni-cad battery, and a carrying bag. Import.
CLASS # 19 14” PORTABLE CHOP SAW The hefty15 amp motor in this Hitachi® 14” chop saw produces a no-load speed of 3,800 RPM for greater cutting efficiency. It is portable, rugged and the lightest in its class at only 36.4 lbs and made to withstand daily transport between trucks and jobsites. The adjustable fence is easy to use and miters 45° to the right or left for versatile applications and the chute on back of the saw diverts sparks and can be angled to suit the workplace.
CLASS # 19 10” BENCH GRINDER This bench grinder has a permanently lubricated, shielded ball bearing motor. The motor and wheels are dynamically balanced to assure even rotation. It has oval end bells and a streamlined motor housing for greater grinding clearance. Die cast aluminum housing and heavy gauge steel construction ensure many years of service.
CLASS # 19 12 VOLT CORDLESS DRILL KIT BOSCH makes it right! These drills have all steel planetary gears, in two variable speed modes: 0 to 400 RPM’s and 1 to 1200 RPM’s. You get two battery packs with 1.4 amp hours of running time. With those and the quick charger, you’ll never run out of power. You get their exclusive “single sleeve” keyless chuck, for fast changes of bits, and there’s even a slot right on the base of the handle to hold the reversible slotted Phillips bit that’s included.
CLASS # 19 14.4 VOLT CORDLESS HAMMER DRILL / DRIVER These cordless hammer drills by SKIL are U.S. made. They come with two 14.4 volt batteries and a quick one hour charger all enclosed in a very rugged, sure-lock carrying case. This package will really do a big job and take a lot of abuse. The drill is ergonomically designed to feel right in your hand and cut fatigue. It is equipped with a soft cushion grip, and sturdy handle you can attach to either side.
CLASS # 19 18V 1/2” CORDLESS DRILL This factory reconditioned Skil® cordless drill will handle the toughest applications. It features an all metal gear train that delivers 400 in-lbs. torque plus the Skil® PowerPlus™ system with Lithium-Ion technology and a 20 +1 position clutch for precise drilling. The keyless chuck allows for easy bit changes and it is variable speed for maximum efficiency. Also features an Energy Star qualified charger for a better environment.
CLASS # 19 18V 4 TOOL COMBO KIT This 18v Lithium Ion tool kit from Skil® features 4 popular cordless tools in one convenient carrying bag. Lithium Ion batteries hold a charge 4 times longer than other batteries so they’re ready whenever you need them. These powerful tools are lighter in weight to reduce user fatigue and the kit comes with two batteries so you’re always ready for any application. All tools in this kit are factory reconditioned kit and feature a one year warranty.
CLASS # 19 ELECTRIC SAWZALL This is the ‘Milwaukee’ Sawzall model # 6507-21. This saw is made by ‘Milwaukee’ Electric in Wisconsin. They are the company that invented the ‘Sawzall’. This model features the 6.5 amp, 450 watt Milwaukee electric motor. The motor speed is variable, 0 to 2600 strokes per minute and the stroke measure a full 3/4”.The shoe is adjustable for versatility and the blade clamp has direct access for quick blade changes.
CLASS # 19 10” MITER SAW This is the Jepson 10” miter saw which is ideal for cutting plastic, metal bar and channel, and non-ferrous metals such as aluminum and copper. It features all ball bearing construction and hardened steel gears for durability. It has a brand new, lighter design, a smart new look and a great new feel. Jepson has added more positive stops in the miter and a much more efficient clamp system. It has a clear, automatic retracting lower guard for visibility and safety.
CLASS # 19 VARIABLE SPEED JIGSAW This is from the new heavy duty line of power tools from SKIL. It is a 5.0 Amp, variable speed Jigsaw that is capable of tackling the most rigorous cuts. It features easy, secure blade change with tool-less blade clamp and will take all standard ‘U- shank’ jigsaw blades. It features a UL listed, double insulated, 5.0 Amp motor, versatile, 4position orbital cut control, and a built in work light.
CLASS # 19 7 1/4” CIRCULAR SAW Anyone who uses tools knows what a ‘SKIL’ saw is because they’re the standard in the industry: known for exceptional cutting accuracy, and smooth power that won’t “bog down” under a heavy load, regardless of the kind of wood; ‘green’ or ‘kiln dried’. These are powerful 13 amp saws with 2.4 horsepower, all ball bearing motors. They’ll cut 2 1/2” deep at 90° and 2” at 45°.
CLASS # 19 7-1/4” CIRCULAR SAW This Skil® circular saw features a 2-point line of sight which increases visibility allowing user to cut straighter lines with ease. The safety lock on the trigger minimizes accidental starts and the anti-snag lower guard allows for smooth operation. A rear level depth adjustment quickly assures accurate cutting depth in material and the durable ball bearing motor gives this saw a longer life.
CLASS # 19 FINISHING SANDER This rugged finishing sander is ideal for an assortment of industrial applications including cabinet and automotive finish sanding. It features all steel ball bearing construction for extra smooth operation and special recessed paper clamps to permit flush sanding on all four sides. It has a comfortable palm grip and a finger touch on/off switch for easier and more efficient sanding and uses just a 1/4 sheet of standard sandpaper.
CLASS # 19 OCTO MULTI SANDER This factory reconditioned Skil® multi finish sander has advanced features to get the job done. Includes 8 detail attachments for finishing hard to reach surfaces with various contours. Includes built in work light to increase visibility in dark corners and three position nose detail to maximize use of abrasives when sanding in corners. It comes with a professional Skil® carrying bag.
CLASS # 19 SHEET PALM SANDER This factory reconditioned Skil® palm sander features pressure control technology with a 4 level LED display which alerts the user when excessive pressure is applied that may reduce the level of professional results. A micro filtration system captures and contains fine particulates that may pass through the weaving of a traditional bag filter and the clear dust canister removes the guess work of when to empty the dust container.
CLASS # 19 3 1/4” ELECTRIC PLANER These are perfect for planing those troublesome doors and one of the handiest tools in the wood shop for quick stock removal and smooth finish on almost any size project. They have a 5Amp motor that turns 18,000 RPM and an electronically counter-balanced single blade system that automatically positions blade at the most effective cutting angle. This eliminates uneven planing caused by misaligned blades.
CLASS # 19 CENTURY BATTERY CHARGERS MODEL 87102 This is the ideal compact battery charger for 6 and 12 volt maintenance free and conventional batteries that are used in cars, trucks, farm equipment, RV and marine vehicles. The 10 Amp setting for the larger vehicles will charge batteries up in 3 to 5 hours while the 2 amp setting is ideal for 12 volt motorcycle or lawn mower batteries.
CLASS # 19 12 & 24 VOLT ROLL-AROUND CHARGER This roll around battery charger has a 600 Amp starter current and an adjustable timer for quick charge, set & forget. It runs on standard 110 Volt household current and has sturdy, rubber wheels. This heavy duty ‘Monster’ battery charger will work with 12V and 24V batteries and is perfect for cars, boats, trailers and RV's.
CLASS # 19 CENTURY FLEET BATTERY CHARGER These battery chargers are USA made by Century. These are the fleet type, the ones on roll around wheels for cars, trucks, and tractors. They can re-charge 6 volt, 12 volt, and 24 volt batteries. They have a big 235 amp starting charge with a timer and automatic shut off. You get a big, easy to read, color coded meter, and automatic resetting circuit breakers to prevent overload.
CLASS # 19 JUMP STARTER W/ AIR COMPRESSOR This 12 volt, self-contained booster pack delivers 900 Amps of peak power and 400 amps of starting power for instant jump starting of a dead battery. They also have a built-in, 260 PSI air compressor for flat tires, air mattresses, inner-tubes, rafts, and balls. This is a perfect take-along supply of jump start power and air power. It has copper, rubber insulated, 4 gauge, 400 Amp jump-start cables that store neatly on the sides of the housing.
CLASS # 19 LITTLE GIANT JUMP STARTER This is the most effective jump starter ever marketed! By compensating for the ‘lost voltage’ in a ‘dead’ battery, the Little Giant doesn’t need a powerful or large battery to jump start a vehicle. Simply put, when the Little Giant is attached to a battery it increases the voltage just high enough to get current flowing through the cables so it can start the car.
CLASS # 19 BATTERY TESTER This is a handy item for any shop, even your home garage. It’s a quick clamp battery tester that will accurately read the charge on any 6 volt or 12 volt battery for auto or trucks. It tests the start cranking charge for excessive current draw and tests the charging system to see if the battery will hold a charge, all with a simple 30 second test. The positive and negative clamps are heavy duty and insulated. The meter is color coded, easy to read, and reads from 1 to 16 Volt.
CLASS # 19 5” x 6” H.D. METAL BAND SAW This is the “SHOP FOX” - 176 lbs. of big band saw cutting power with a 5” capacity in round stock and a 5” x 6” capacity for rectangular stock. The 110V/220V motor is 1 horsepower, single phase that delivers 2000 RPM and it is all ball bearing. It has an automatic shut-off and all ball bearing blade guide as well as three different blade speeds: 80, 120, & 200 FPM (feet per minute).
CLASS # 19 BAND SAW WITH LIGHT This factory reconditioned Skil® band saw features a laser cutline guide for accurate cuts every time. The articulating LED worklight ensures that the work piece is clearly lit. EZ view blade tracking makes blade alignment very simple and a quick change blade system provides fast and easy blade changes. It has a rack and pinion table adjustment for quick angle and height adjustments as well as a rip fence for straight, accurate cuts.
CLASS# 19 12 VOLT CORDLESS CAULKING GUN This is a 12 Volt Cordless Caulking gun that will really save time and elbow grease on your kitchen, bath, windows or any other caulking project. It takes standard sized 10 Oz. caulk tubes, and works with most caulking compounds including urethane. It is variable speed from 0 to 270 mm per minute which puts you in control and reduces wasted ‘over-caulking’.
CLASS # 19 ACE 10” TABLE SAW These 10” table saws are the ideal answer for cross-cutting, ripping, angle and miter cuts in both hard and soft woods. They come with a 10” x 40 tooth carbide tipped blade with a depth of cut that is adjustable up to 3” at 90°. The blade tilts for bevel cutting to 45° and it has a built in miter gauge for angle cutting to 60°.
CLASS # 19 10” TABLE SAW This factory reconditioned Skil® 10” table saw features a 15 Amp, 5000 RPM motor for cutting through treated lumber. With the integrated handles, it is easily transported from site to site. It has a large die cast aluminum table and self aligning rip fence with EZ View measurement system for accurate settings and measurements. A miter gauge guides the work pieces when making rip cuts and the soft-grip control handles add increased comfort and less fatigue.
CLASS # 19 WET TILE SAW This factory reconditioned Skil® wet cutting tile saw features a stainless steel tabletop that is resistant to corrosion. It has an adjustable rip fence with miter gauge for accurate straight and miter cuts and 0-45° bevel for a wide range of cuts. The water reservoir keeps the blade cool and minimizes dust and debris. Uses a 7” diamond blade, (one blade is included.) Factory reconditioned. Specifications: • • • • • • • • • • • 4.
CLASS # 19 18 VOLT CORDLESS CIRCULAR SAW These cordless circular saws have a 5-3/8” blade and 18 volts of battery power. The no load speed is 2400 RPM, so it won’t bog down on tough cuts. It has an adjustable cutting plate and rip fence and set up just like a standard, corded saw. They bevel cut to 50° to give you more versatility and have a maximum cutting depth of 1-1/2” at 90° and 1-1/8” at 45°. They’re easy to handle with an ergonomically balanced design which reduces hand and arm fatigue.
CLASS # 19 ROTOZIP SAW BITS This is a pack of 10 bits with a 1/8” shank and both fit in the collets of any manufacturer’s zip saw but are genuine Bosch® RotoZip® bits.
CLASS # 19 7” ELECTRIC CUT-OFF SAW This 7” cut off saw is just like the big 14” model, but without all the bulk and size. You can easily move it around with one hand like a circular saw. It weighs just 11 lbs. with the built in base yet it has a powerful 5 amp motor that turns at a maximum 8,300 RPMS. The heavy duty trigger can be locked ‘on’ for continuous cutting, and the built-in spindle lock and 7/8” arbor makes changing wheels a snap. You can even make bevel cuts by adjusting the base.
CLASS # 19 7” BENCH TOP TILE CUTTER This powerful, bench top tile cutting saw will cut tile up to 12” wide and 1” high. The heavy duty, chrome plated table is 15” x 15” and tilts to 45° for bevel cuts. It features a 1-1/2” wide locking fence and a ‘V’ block for stabilizing the piece being cut and is powered by a single phase, 110 volt, 3/4 hp motor. This saw will cut wet or dry and includes a PVC tub underneath the table for the water or coolant bath. It has a 1” arbor and turns at 3,600 RPM.
CLASS # 19 GAS POWERED PRESSURE WASHER This is a 2,000 PSI, gas powered pressure washer, an essential tool for painters, mechanics, homeowners, and professional cleaners. It features a 2.4 hp. easy start, four stroke commercial engine and it will run for hours on just 1.6 liter of unleaded fuel. It includes a commercial grade, high pressure hose and spray gun, and four quick change nozzles to vary the spray pattern and intensity.
CLASS # 19 1,800 PSI ELECTRIC POWER WASHER The Campbell Hausfeld electric pressure washer is ideal for decks, driveways, fencing, siding, vehicles and other equipment. It has a heavy duty universal motor and a turbo lance that boosts PSI to 1,900. The fan lance is adjustable from 0°to 60° and it is equipped with a hose reel for easy storage and mobility as well as a 35’ GFCI power cord for safety. It’s also equipped with an on-board rear detergent tank and large wheels for easy transport.
CLASS # 19 DIGITAL AC/DC MULTIMETER This compact, digital, 3-1/2 digits multimeter is used for measuring both AC (alternating current) and DC (direct current) voltage , current, resistance, diode, transistor, battery and continuity. They feature polarity indication, data hold, over range indication, and an auto power off. They are easy to operate and ideal for use in the field, work shop, laboratory, or home applications. Includes the test leads, a cradle with a folding stand and a 9V battery. Import.
CLASS # 19 2 PC. 16” SDS DEMOLITION CHISELS This is a 2 piece set of demolition hammer chisels that fit the demolition hammer # AE133. They have the SDS 1-1/8” shanks and are made of heavy gauge steel. There is one 16” bull point and one 16” flat chisel in this set and they are packed in separate, plastic tubes. Each chisel weighs approximately 4 lbs. ITEM#: AE133CH DESCRIPTION: 2 PC.
CLASS # 19 ELECTRIC DEMOLITION JACKHAMMER WITH 2 CHISELS This Demolition Hammer is a Monster!! It weighs in at a whopping 53 lbs. and comes complete with two huge chisels and everything you need to start busting into that hard concrete or asphalt you have to remove. You even get a pair of cotton gloves in the mix. It is electric, 110 volt ~ 60 Hz. 1240 watts and a no load speed of 1400 RPM’s. It has a 360º swivel side handle with rubber grips and the heavy duty metal housing is rust resistant.
CLASS # 19 This Industrial, electric demolition hammer is a beast!! 1700 Watts of mean, busting, breaking machine!! It packs 1,000 to 2,100 BPM for the most brutal busting of concrete, asphalt, or anything else that gets in its’ way! Features a padded rear handle and a sure grip, padded side handle for user comfort, and comes with 2 monster SDS chisels and a heavy duty, blow mold carrying case with two rugged wheels on one end and a grab handle on the other so the unit can be easily rolled from job site to
CLASS # 19 115 VOLT PORTABLE SPOT WELDER Spot welding is a type of resistance welding used to weld various sheet metals. The process uses two shaped copper alloy electrodes to concentrate a welding current and force between the materials to be welded. The result is a small ‘spot’ that’s quickly heated to the melting point, this forms a nugget of welded metal after the current is removed.
CLASS # 19 3” x 21” BELT SANDER WITH BAG These are compact, heavy duty belt sanders that are right at home in a production wood shop. They’re 760 Watt, 110 volt, electric sanders that have the attached bag, so the shop or worksite stays clean. The motor is double insulated, all ball bearing with a heavy duty, locking trigger switch. You get a belt speed of 1,378 feet per minute and a quick belt adjustment that makes belt change easy and lets you get right down to work.
CLASS # 19 11 AMP RECIPROCATING SAW The Bosch reciprocating saw makes cutting easy with its lightweight feel and comfort grip and the dual LED light illuminates cutting areas. 11 amps make this saw the most powerful tool in its class. It has a tool-less blade change system for fast and effortless blade change and removal and the saw hook allows convenient storage between cuts. The variable speed trigger improves cutting control in various materials and the cutting capacity is 1-1/8”.
CLASS # 19 FINECUT POWER HANDSAW This is the ideal tool for flush cutting doorjambs, window jams, shims, PVC drainpipe, flooring and more with its versatile, flush-cutting ability. It features a 3.5 Amp, 2,000 to 2,800 RPM motor, an innovative anti-vibration system for low vibration and smooth cutting, and a variable speed dial to match the speed to the workplace and task. This tool is light and compact for better maneuverability in different job applications and is easy to use even in tight spaces.
CLASS # 19 12 VOLT CORDLESS GREASE GUN Here’s the answer to a messy problem. These cordless grease guns are 12 Volt, which is plenty of power to deliver a runoff capacity of up to one and a half ounces per minute at 6,500 PSI so you don’t need to drag around an air hose, or extension cord, or crank on a manual gun. Greasing bearings or zirc fittings is now fast and fun again...with no mess. They have a 14 1/2 oz.
CLASS # 19 18 VOLT CORDLESS GREASE GUN This 18 Volt, cordless grease gun will deliver fast and easy fleet service out in the field, and now, with the added feature of a 12 Volt thermal warmer the grease will keep flowing even under the coldest weather conditions. You simply wrap the warmer around the grease cartridge and plug it in to any 12 Volt cigarette lighter receptacle until desired temperature is reached.
CLASS # 19 1/2” CORDLESS IMPACT WRENCH These cordless impact wrenches deliver 280 foot pounds of torque. You can change a flat tire in no-time, or have reserve power for a tough situation like driving big lag bolts, or securing heavy machinery. They can be used on production assembly lines or big shop projects. Instead of using an air power wrench and snaking the hose all around and over your work, you just grab a cordless impact wrench, and you’re done! These Impact Wrenches are 24 volt and reversible.
CLASS # 19 3.6 VOLT CORDLESS SCREWDRIVER This is a handy little tool to have around; a 3.6 volt, quick rechargeable screwdriver with an assortment of 29 screwdriver bits, (Philips, flat, hex bit, torx, and star), and 8 sockets, (1/4” to 1/2”). The palm-grip driver can also be configured either straight or at an angle for any spot you need to get into.
CLASS # 19 4.8 VOLT CORDLESS SCREWDRIVER KIT Use this handy, little cordless screwdriver for mounting shelves, changing hardware, assembling furniture and a thousand other jobs. It features a 4.8v, 180 rpm motor that charges in 3 to 5 hours and an LED work light. It has a rubberized grip, an LED battery indicator and comes with eleven 1” screwdriver bits, a 2” magnetic bit holder and one UL approved charger. Imported. ITEM#: DESCRIPTION: AE145 4.
CLASS # 19 ELECTRIC CHAIN SAW SHARPENER These new sharpeners can be mounted to your bench or the wall. The clamping vise adjusts to all chain designs and pitches, and gives you the precise angle adjustments to keep your chain in top condition. It’s easy to get the proper height and scale positioning, so you get double the chain life and much smoother cuts. IMPORTED Specifications: ¾ ¾ ¾ ¾ 120 Volt / 60 Hz 0.75 Amps 85 Watt 4200 RPM grinding free speed.
CLASS # 19 14” HEMI GAS CUT-OFF SAW This powerful 14” gas cut-off saw features a 4.8 horsepower ‘HEMI’ engine and state of the art technology. The steel alloy ring has been coated with PCVD while the cylinder has a hard, ceramic coating. Together they reduce friction and form a clean burning system that generates more power and ensures longer life.
CLASS # 19 18” WALK BEHIND CONCRETE SAW Engineered for compactness, maneuverability and reliability. One-piece box construction chassis made from 3/16" hot-rolled steel that will not flex during operation and has a powder-coated chassis that resists peeling and corrosion. The 18" blade capacity with 18" blade guard provides for a depth of cut of 6-5/8" and the heavy-duty 1" dual blade shaft assembly with self-aligning pillow block bearings ensure accurate cutting on either left or right side.
CLASS # 19 14” WALK BEHIND CONCRETE SAW (W/ HONDA ENGINE) This is a compact, lightweight, walk-behind concrete saw with 6-1/2 hp gas powered Honda® motor. The 14" blade capacity provides a 5-1/2" depth of cut. It features an adjustable depth control, left and right cutting capability and throttle control on the console. This saw can be used for both wet and dry applications and has built-in water distribution system that supplies water to both sides of the blade.
CLASS # 19 14” WALK BEHIND CONCRETE SAW (W/ ROBIN ENGINE) This is a compact, lightweight, walk-behind concrete saw with 6 hp gas powered Robin® motor. The 14" blade capacity provides a 5-1/2" depth of cut. It features an adjustable depth control, left and right cutting capability and throttle control on the console. This saw can be used for both wet and dry applications and has built-in water distribution system that supplies water to both sides of the blade.
CLASS # 19 4 1/2” ELECTRIC GRINDER This is the powerhouse 4 1/2” hand grinder made by SKIL, and used by professionals all over the World. These right angled grinders are heavy duty and super versatile. They have a powerful 6 amp motor and an 11,000 RPM (no load speed). They grind, sand, sharpen, and cut various stone, brick, metal, and wood materials. It has an all metal gear housing, and a heavy duty, quick release, wheel guard, with a “lock-on” trigger switch to cut fatigue.
CLASS # 19 135 AMP FLUX/MIG WELDER This heavy duty, portable, 135 Amp, ‘Tweco Style’ Flux/Mig welder is a compact 115 volt unit that will breeze through Mig welds on a wide range of materials including mild steel, stainless steel, and aluminum. It also handles flux-cored welds on mild steel with ease, so you’ll get through any repair or project in no time! The large, easy to set, easy to read knobs provide adjustable tap voltage control and a continuous full-range control of wire feed speed.
CLASS # 19 8,000 WATT 13 HP GENERATOR Power outages can happen anytime. You just can’t fight Mother Nature. Well, you can’t fight her but you can sure be prepared when she does get a bit angry. This 8,000 Watt, 13 HP generator has plenty of power to get you out of the dark in case of an outage. It has a large 5.
CLASS # 19 3,000 PSI GAS PRESSURE WASHER This is a true professional quality, full-featured power washer with all the bells and whistles that professionals demand. It has a smooth, powerful 5.5 HP, low emission, overhead valve engine that powers 2,200 PSI of working pressure with a maximum PSI of 3,000. It includes a 16’ non-marring rubber, high pressure hose, a stainless steel spray gun with 4 interchangeable nozzles for a variety of spray patterns, and intensity quick-connect/disconnect hose couplers.
CLASS # 19 6 GALLON WET & DRY SHOP VAC Clean up your shop or garage with this industrial strength wet and dry vacuum cleaner. This 6 gallon capacity shop vacuum can easily pick up wet or dry messes in no time at all and is great for any task. It features a powerful 2.25 hp motor to siphon messes directly into its large tank. The Koblenz® vac also includes an air blower that works great for moving massive amounts of debris and the 6’ hose features a positive lock system designed to maintain suction power.
CLASS # 19 14” CUT-OFF SAW This 14” Cut-Off saw from ‘Neiko Tools USA’ is designed for the fastest no-stall cutting in all professional applications. It features a 15 Amp., 2.5 HP long life motor with a free speed of 3,800 RPM. It has a quick-adjust vise, a sturdy steel base with non-slip rubber feet and a more natural, straight on ergonomic handle. The guide plate adjusts 45° to the left or right and the spindle lock allows for quick wheel changes. Takes a 14” abrasive wheel with a 1” arbor.
CLASS # 19 BUFFER/GRINDERS - 10” & 6” These are industrial rated, bench type buffer/grinders that feature a cast iron base for very low vibration as well as a shielded, permanently lubricated ball bearing motor. They are 120 Volt, 60 Hz. and come with two buffing wheels. Can be used as a grinder with an optional grinding stone, (not included.) Imported 10” GRINDER / BUFFER a a a a a 1,720 - 3,450 RPM 1/2 - 3/4 HP 3 - 4.5 Amp 3/4” Arbor 60 Lbs.
CLASS # 19 10” COMPOUND MITER SAW W/ LASER This 10” retractable compound miter saw comes complete with one 10” carbide blade and has a powerful, 15 amp motor that delivers 5,300 RPM. It cuts angles from 0° to 45° and has capabilities for cross cuts, miter cuts, and bevel cuts all in one. The base is equipped with built-in clamps to hold down any material to be cut and the electrical cord is in a harness on the saw so it won’t get in the way. It also features a built in laser guide for perfect cuts.
CLASS # 19 COMPOUND MITER SAW This factory reconditioned Skil® 10” compound miter saw features the Safe-Cut system, designed for safe operations. A horizontal clamping system holds wood securely against the fence during cutting and the table extension with the extension rail supports long, large work pieces. There are 9 positive stops for setting common miter angles and the die cast aluminum fence has ruler markings for accurate cutting. There is also a dust bag to help keep work area clean.
CLASS # 19 12” COMPOUND MITER SAW W/ LASER This 12” retractable, Compound Miter Saw from ‘Neiko USA’ features a gear driven arm assembly for smooth blade guard retraction, and sliding dual rails with 3 linear ball bearings which provides for a super wide cut up to 12” in width. It has an easy to read miter scale with 9 detent lock stop left and right for stability and accuracy, a die cast aluminum table and back fence, and a very durable base for improved stability and reduced vibration.
CLASS # 19 NEIKO 10” TILE SAW WITH STAND This professional grade tile saw cuts tile up to a depth of 3”, 24" square and 16" diagonally. You get an installer’s grade 10” tile saw, 10" standard continuous rim wet diamond blade, a folding stand with rear wheels and brakes, high volume water pump, front and side cutting table extensions, miter block and rip guide.
CLASS # 19 6.5 HP 3500 WATT GENERATOR These are overhead valve, 4 stroke, and forced air cooled engines in a square-tube roll cage. They have a four gallon extended run fuel tank and gauge, and operate at only 68 decibels. These make great emergency standby units for the home or vacation home and are very popular for boating, camping, and RV’s. They surge to 3,500 watts, and run continuously at 3,000 watts and has two 120 Volt receptacles.
CLASS # 19 ENCLOSED DIESEL GENERATOR This diesel powered generator features a single cylinder, 4 cycle engine that produces 6,000 watts of maximum output power. Because the engine is enclosed, this generator runs quieter and is protected from outside elements such as dirt, debris and weather conditions. It has (3) 120 volt outlets; (2) 20 amp and (1) 30 amp with a twist lock, as well as a 120/240 receptacle rated at 30 amp. It’s also equipped with a DC overload switch, circuit breaker and electric start.
CLASS # 19 DIESEL WELDER & GENERATOR This diesel powered generator –welder combo features a 4 stroke injection diesel engine that powers at a continuous output of 3000 watts. It has a 3.04 gal fuel tank and an automatic shutdown for low oil pressure. It will run for 12 hours at 50% load and is equipped with an electric starter, and a forced air cooling system. The welding current range is 80 – 200 amps and noise level is just 82db. Battery is not included.
CLASS # 19 NEIKO 4 1/2” ANGLE GRINDER These 4 1/2” grinders by Neiko have double insulated 5.8 Amp motors and turn 11,000 RPM (no load speed). They have the 7/8” arbors, the ‘lockon’ trigger button, safety guard, and the two position, long back side handle. They feature all aluminum gear housings and tough ABS molded bodies. These grinders are simple to use, they’ll take the abuse, and they’ll just keep on running. One 4-1/2” abrasive wheel is included.
CLASS # 19 NEIKO DRILL BIT SHARPENER This is a quick, easy, and accurate sharpener for your everyday drill bits. It has a 0.5 Amp motor that spins the grinding wheel at 1,420 RPM. and it’s thermally protected in a high-impact plastic housing. It’s equipped with a 6’ cord and a heavy duty rear mounted on/off switch. This unit has two sharpening heads and two extra grinding stones. The first head will sharpen bits from 1/8” to 3/8” (3.5mm – 10mm).
CLASS # 19 7-1/4” CIRCULAR SAW WITH LASER These new laser guide saws by Neiko® are quickly getting the name for quality and precision. Beveled gearing and all ball bearing, 10 amp motors make these saws quiet and reliable for years. They run at 4,500 rpm, (no load speed), and will easily cut green or wet material without bogging down. They have a 2-1/2” cutting depth at 90º and a 1-13/16” cutting depth at 45º.
CLASS # 19 ELECTRIC PIPE THREADER This is a heavy duty, hand held pipe threader with a 110 Volt, 2-1/4 HP motor. They have a bright orange ABS body with heavy duty switch and 6’ power cord. The motor housing and handle are cast aircraft aluminum to dissipate the heat quickly. It turns at 23 RPM and will smoothly and accurately thread pipe from 1/2” to 2” NPT. It has precision cut, alloy steel pipe clamp blades. Includes 6 cast iron threading dies: 1/2”, 3/4”, 1”, 1-1/4”, 1-1/2” and 2”.
CLASS # 19 NEIKO ORBITAL JIG SAW WITH LASER These jig saws have 5.5 Amp motors for full power, an orbital stroke that will saw in a number of different materials like wood and steel, as well as various fiber boards and paneling. It has a variable speed dial with 3 orbital action settings, a bevel cutting facility for 0-45° left to right and a cutting capacity of 60mm in wood and 5mm in steel.
CLASS # 19 NEIKO 3/8” CLOSE QUARTER DRILL This 3/8” electric drill is a great little unit for getting into tight spaces where a regular drill just won’t work. It’s a palm held drill with a 55° angle at the key chuck and with the efficient paddle switch you’ll also have room for your fingers as well. It is reversible, lightweight and ergonomically built for comfort.
CLASS # 19 ROTARY TOOL KIT This Rotary tool kit features an 8,000 to 30,000 RPM variable speed, 1 amp motor, a flexible shaft, a height adjustable stand and a 40piece assorted accessory kit with the more popular items to get you started. The variable speed dial provides much more control than those other rotary tools with the slide control. Use this tool instead of a dremel because of the remarkable speed control. • • • • • • • • Specifications: 120 Volt, 60 Hz.
CLASS # 19 220 PC. ROTARY TOOL KIT This kit includes a variable speed, pistol grip rotary tool rated at 1.2 amp and 8,000 - 30,000 RPM. It has a keyless chuck for fast and easy bit changes and has a full assortment of accessories for polishing, grinding, cutting, engraving and more. The kit comes in a very handy see through organizer carrying case and the tool fits all brands of rotary tool accessories with 3/32” and 1/8” shanks.
CLASS # 19 MULTI-FUNCTION POWER TOOL At 6,000 to 21,000 oscillations per minute, (OPM), this multi-function power tool can handle any tough job. It will cut plastic materials, air ducts, plasterboard, and pipe as well as sanding cement, concrete, stone, plaster, wood, adhesives and paint. Features a comfortable non-slip grip, a variable speed dial for precise control, and a powerful 2.0 amp motor for a variety of projects.
CLASS # 19 ACCESSORIES FOR MULTI-TOOL These accessories are for the multi-function oscillating tool, item# AE148. 21 PC. SANDPAPER SET Includes: • • • • (7) 80 grit (7) 100 grit (7) 120 grit For universal sanding applications ITEM#: AE148S1 _________________________________________________________ 3 PC. SAW & SCRAPER SET Includes: • 3-1/8” HSS semi-circle saw blade.
CLASS # 19 1,000 WATT POWER INVERTER A power inverter, quite simply explained, converts DC (Direct Current) power into conventional AC (Alternating Current) power allowing you to use your favorite electric devices when an AC outlet (household plug) is not available. You simply connect an inverter to a battery source, e.g., car or truck battery, plug in your device and you’re all set. This inverter, by ‘Neiko Tools USA’, features 1,000 watts of continuous power with a peak load of 2,000 watts.
CLASS # 60 14” GAS CUTOFF SAW Partner® was the first on the market with hand held cutters in 1958. After extensive usage and updates, this 14” portable cutoff saw is the one used by emergency crews and masonry contractors all over the world. Now merged with Husqvarna®, this is the best demolition saw on the market. This saw features a 4.8 HP air cooled, 2 cycle 71 cc engine and it weighs just 20 lbs.
CLASS # 19 36 AMP PLASMA CUTTER Plasma cutters are fast, clean, and can cut intricate patterns that torches cannot and, there is little de-burring required. They swiftly cut steel, carbon steel, and aluminum. It uses shop air (only3.5cfm at 65 PSI) and no special gases are required. Science lesson: If you boost a gas to extremely high temperatures, you get plasma. The energy begins to break apart the gas molecules, and atoms begin to split. In plasma, the electrons separate from the nucleus.
CLASS # 19 60 AMP PLASMA CUTTER Plasma cutters are fast, clean, and can cut intricate patterns that torches cannot and, there is little de-burring required. They swiftly cut steel, carbon steel, stainless steel, aluminum and even copper. It uses shop air (only 4cfm at 70psi) and no special gases are required. This powerful 60 amp plasma cutter will easily cut through steel up to 1-1/4” thick. Includes torch assembly, grounding clamp, 3 electrodes, 3 tips and air hose.
CLASS # 19 50 AMP MULTIPURPOSE WELDER This multipurpose welding machine features industrial technology in a 200Amp DC Tig Welder and a 50Amp continuous arc plasma cutter, which means the arc can be ignited in the air and will not go out when you have to go through metal. It has the most powerful torch available without needing a water cooler unit. (Caution: torch gets extremely hot on long welds).
CLASS # 19 PALM ROUTER The Bosch® Colt is a compact, yet spirited performer. This 1.0 HP palm router is a very versatile tool and not just a laminate trimmer, but is ideal for trimming deck planks, hinge mortising, edge forming, slot cutting, window cutouts, dovetailing, and decorative inlays. Features a palm grip design with Soft Grip and finger support pockets to make it the most comfortable router in its class.
CLASS # 19 2,850 PSI ELECTRIC POWER WASHER This high pressure power washer features a maximum pressure of 2,850 PSI with a rated working pressure of 1,500 PSI. The water flows at 1.6 GPM and operates on standard 120 Volt household current. Import. Specifications: • • • • • • • • 120V / 60Hz / 13A Rated Pressure: 1,500 PSI Maximum Pressure: 2,850 PSI Water Flow: 1.
CLASS # 19 SPIRAL SAW This is the original framing and drywall cutting tool by Bosch®, a leader in the manufacture of industrial cutting and drilling tools. RotoZip’s Spiral saw is capable of making precise cuts in a large variety of difficult materials. The dust sealed switch keeps debris from the power mechanism and the foot is completely adjustable for cutting up to 1” thick. It has a 5/32” collet system for use with XBIT accessories a ‘Walkman’ style, padded handle.
CLASS # 19 RECIPROCATING SAW Specifications: a a a a a a 8.5 Amp motor Variable speed RPM Adjustable pivoting shoe Comfort grip On-tool blade storage Tow finger trigger for less user fatigue a Vibration control gearing a One year warranty a Blade not included The Skil® reciprocating saw features a big 8.5 Amp motor which delivers enough power for any construction and demolition job, and with the variable speed control, can be adjusted for clean, fast cuts on any material.
CLASS # 19 3” x 18” BELT SANDER This Skil® belt sander has 33% more power than the earlier model Skil belt sanders and will sand any type of wood surface. The belt measures 3” wide x 18” circumference and the sander features the patented auto track alignment which keeps the belt centered and it will not slip off. The micro filter dust canister keeps the work area clean and free from fine wood dust particles and flush edge sanding provides sanding right up to the edge.
CLASS # 19 1 HP SUBMERSIBLE PUMP The ‘Little John’ submersible pump is designed to transfer standing water, and other liquid from one location to another, in a quick and efficient manner. They are commonly used to clear standing water from rain or flooding on a job site, basement, pool, or any other area where water has accumulated. They have a pump rate of 3,434 gallons per hour and are easy to use. Just hook up a discharge hose, submerge the unit in the section to be cleared, and plug it in.
CLASS # 19 TRASH WATER PUMP This 2", 6.5hp trash water pump is suitable for all industrial, agricultural, emergency flooding or daily home usage. Features a light weight, portable size, powerful smooth running engine and easy maintenance. Specifications: • • • • • • • Power: 6.5HP 4 Stroke OHV Engine Inlet/ Outlet Diameter: 2" Suction Height: 8m Pump Lift: 26m Max Flow: 550L/Min Fuel Tank: 3.
CLASS # 19 JOBSITE CD/MP3 PLAYER This factory reconditioned Bosch® integrated jobsite CD player features MP3 compatibility, 40 second skip-free protection, an AM/FM stereo tuner with 30 station presets and a remote control. It has separate bass and treble controls, 4 preset equalizer settings and enhanced ‘Bosch sound’ for great listening even on the busiest jobsite. It is all protected by an aluminum roll cage with rubber elbows on each corner which allow it to withstand a 10’ jobsite drop.
CLASS # 19 PORTABLE SPACE HEATER The Airmaster™ portable heater features a heat circulating fan, two comfort heat settings and overheat and tip-over protection with automatic shutoff. At 750-1,500 watts and 5,120 BTUs, it’s powerful enough to warm an average sized room. It is compact, completely portable and UL listed. Specifications: • • • • • • • • • • • ITEM#: 891 Motor: 120 V, 1 phase Dimensions: 7.9”W x 11.4”H x 5.9”D Weight: 4 lbs.
