Studio Equipment Safe Operating Procedures Drawing and Painting Studio Office of Safety & Risk Management Rosalie Sharpe Pavilion 115 McCaul Room 2210
------------------------- This page intentionally left blank ---------------------------
Jigsaw Machine Jigsaw Model: 1584VS Location Drawing and Painting – 475 Manufacturer Name: Bosch Address: Robert Bosch Limited, Broadwater Park, Denham, Uxbridge, Middlesex, UB9 5HJ Tel: 0844 7360107 Applicable Legislation CAN/CSA-Z432-04 Safeguarding of Machinery Sources Manufacturer’s Manual Safe Work BC, CCOHS, and IAPA resources REA Engineer Specifications Studio Technicians DO NOT USE THIS MACHINE UNLESS YOU ARE TRAINED IN ITS SAFE USE!
1.
2.0 Pre-use Inspection Checklist Check 1 Are the power cords free of frays and damage? 2 Do you know where the emergency stop feature is located (button/switch/cord)? Plug may be used as an emergency stop.
3.0 Safe Operating Procedure (SOP) This procedure is outlined as follows: General Safety Guidelines Equipment Specific Safety Operating Procedure 3.1 General Safety Guidelines Before using the machine, perform the following general safety checks: a) Notify the studio technician/class assistant or faculty that you are operating this machine. b) Make sure you understand all of the instructional material and/or faculty and technician instruction before operating this equipment.
Equipment Specific Safe Operating Procedure (SOP) 1. Before sawing a) Put on required PPE. b) Mark the areas to be cut. c) Preselect the stroke rate using the thumbwheel, the pendulum action and d) e) f) g) h) i) the air stream using the adjustment levers (depends on the material being used). Keep the pendulum action off when working on thin materials. Select the cutting angle adjustment. Select the base plate.
3. After Sawing a) Turn off the jigsaw but do not place it down until it has come to a complete stop (danger of backlash). b) Disconnect the saw when not in use. c) Don’t touch the blade or work piece immediately; they may be extremely hot, resulting in burns. d) Remove the chips from the surrounding area with a brush-NEVER by hand. e) Clean the saw-use a rag to clean the blade-careful that the cloth does not hook on the teeth-NEVER clean while in motion.
4.0 Maintenance and Repair 4.1 Inspection Checklist DAILY Ensure that the power cords are free of frays and damage. Ensure that the saw is secure with no loose parts. Ensure that all bolts/adjustments are tight. Ensure that the tool foot is in good condition. Ensure that the blade and teeth are free of defects and dullness and centered between the guides-replace if necessary-use gloves. Ensure the guides are in good condition and properly adjusted.
------------------------- This page intentionally left blank ---------------------------
Mitre Guillotine Machine Miter Guillotine Model: MORSO-F Location Drawing and Painting – 475 Manufacturer Name: Morso Dan-List Address: Haraldsvej 21, DK-8960 Randers, Denmark Tele: +45 8643 5155 Applicable Legislation 1. CAN/CSA-Z432-04 “Safeguarding of Machinery” 2.
1.
2.
Equipment Specific Safe Operating Procedure (SOP) Picture 1 1. Before cutting a) Put on required PPE b) Mark the desired area(s) to be cut. Don’t cut a work piece with flaws, nails, c) d) Picture 2 e) Picture 3 3.2 f) g) h) i) or other foreign objects-to prevent personal injury from flying material. Loosen the hand levers to adjust the angle of the fence according to the measuring scales on the table (see picture 1). For a double mitre cut, adjust the fence angle at 45 degrees.
Picture 4 2. Cutting Beware of the extremely sharp knives. Stand right in front of the machine for accessibility to the foot pedal. Lower the pedal at a moderate speed, and make the cut. Ensure you have a secure footing on the foot pedal (see picture 4). Never stand on the foot pedal. Once you release the foot pedal the knife will return to the starting position.
4.0 Maintenance and Repair 4.1 Inspection Checklist DAILY Ensure that all guards are in place and in good working order. Ensure that the area around the guillotine is free of slip/trip hazards. Ensure that the debris/material from previous operations are removed. Ensure that all tools/wrenches are removed from the table. Ensure that the angle lever knob is in good working condition and not loose. Ensure that the foot pedal moves freely. Ensure that the blade is tracking in the correct position.
------------------------- This page intentionally left blank ---------------------------
Spray Booth Machine Spray Booth Model: FABF-5 Location Drawing and Painting – 475 Manufacturer Name: Paasche Address: 4311 N. Normandy Avenue, Chicago, IL 60634-1395 Telephone: 773-867-9191 Applicable Legislation Occupational Health and Safety Act and Regulations for Industrial Establishments (R.R.O.
1.
2.0 Pre-use Inspection Checklist Check 1 Is the ventilation system turned on? 2 Is the spray booth area free of slip/trip hazards? 3 Are flammable/combustible materials removed from the spray booth? 4 Has the debris/material from previous operations been removed? 5 Are the spraying materials (paints, primers, sealers, and other coatings) ready for use? 6 Is the spray booth free from electrical equipment, switches, lights, or other devices? Y N N/A Comments/Corrective Action: 3.
Equipment Specific Safe Operating Procedure (SOP) 1. Before using the spray booth a) b) c) d) e) f) Have the spraying material (spray cans/airbrush) ready for use. Read the MSDS for the chemical being used. Put on required PPE Turn on the ventilation system. Prepare your material to be sprayed. Use the spray booth only for spray painting and coating. 2. Using the spray booth a) All spray painting should be done in the spray booth.
4.0 Maintenance and Repair 4.1 Inspection Checklist DAILY Ensure the spray booth area is free of slip/trip hazards. Ensure flammable/combustible materials are removed from the spray booth. Inspect the spray booth and do maintenance work. Ensure debris/material have been removed after each use. Ensure the spraying materials (paints, primers, sealers, and other coatings) are stored on the designated shelf or flammable cabinet.
------------------------- This page intentionally left blank ---------------------------
Hand Drill Machine Hand Drill Model: 10mm 6510LVR Drill / 13mm NHP1310 Hammer Drill Location Drawing and Painting – Room 475 Manufacturer Name: Makita Electric Works, Ltd.
1.
2.
Equipment Specific Safe Operating Procedure (SOP) 1. Before Drilling Put on required PPE. Mark the areas to be drilled. Secure the work piece with a clamp/vise-NEVER work free hand. Install the bit as far into the chuck as possible-do not do this when operating the tool. e) Tighten the chuck by hand. f) Select the direction of rotation using the reversing switch lever (see picture 1). Picture 1 a) b) c) d) 2. Drilling Picture 2 3.
4.0 Maintenance and Repair 4.1 Inspection Checklist DAILY ✔ Ensure that the power cord is free of frays and damage. Ensure that the drill is secure with no loose parts. Ensure that the drill, chuck and bit are free from cracks and defects. Ensure that all screws are securely tightened. Tighten if required. WEEKLY ✔ Clean all drill parts. MONTHLY ✔ Lubricate moving parts to prevent rusting and minimize friction related wear. ANNUALLY ✔ Inspect entire machine and perform maintenance as required.
------------------------- This page intentionally left blank ---------------------------
