Power Tool Safety Rules Read and understand all instructions. Failure to follow all listed below, may result in electric shock, fire and/or serf outs personal injury. instructions SAVE THESE INSTRUCTIONS Work Area Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust of fumes.
job» better and safer at the rate for which it is designed. Do not use tool if switch does rot turn it “QN” or “OFF”. Any tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. Store idle tools out of reach of children and other untrained persons.
Do not use this tool with “Woodcarving” blade or standard wood culling toothed blades. These blades are not intended for this machine and can create loss of control siring use. Abrasive Cul Off Wheels must have a manumit safe operating speed greater than the “no load RPM” marked on the tool's nameplate. Wheels running over the rated speed can fiy apart and cause injury, Before each use inspect the cut off wheel for chips and cracks. Do not use a wheal that may be damaged.
Maintain a firm grip with both hands on the machine handles and position your body and arm to allow you to resist recoil forces. Recoil forces can be controlled by the operator. if proper precautions are taken. When wheel is binding, or when interrupting a cut for any reason, release the trigger and hold the machine motionless in the material until the wheel comes to a complete stop.
Symbols IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. Symbol Name Designation/Explanation Vv Volts Voltage {potential} A Amperes Current Hz Hertz Frequency (cycles per second) Ww Watt Power kg Kilograms Weight min Minutes Time s Seconds Time oF Diameter Size of drill bits, grinding wheels, etc.
Functional Description and Specifications A WARNING Disconnect the plug from the power source before making any assembly, adjustments or changing accessories. Such preventive safety measures reciter the risk of starting the tool accidentally. Abrasive Cut-Off Machine FOOT PLATE WING NUT LOCATING TABS ~ Ga SECURING CAP SCREW ~~ LOCATING SPINDLE NOTCHES SPINDLE LOCK AUXILIARY HANDLE ~~ “> MOUNTING BOLTS a Model No. 1364 1365 Maximum capacities Abrasive wheel 12" 14" Max.
Assembly To prevent serious personal LL ELL injury, always disconnect the plug from power source before changing wheels, or making any adjustments. INSTALLING ABRASIVE WHEELS Always use the arbor nut that has mass thread size as spindle. 1. Install inner flange onto spindle, with recess in back side of flange engaging matching area on spindle, 2. Install abrasive wheel onto spindle. 3. Install outer flange with flat side out, 4.
OPERATING THE TOOL Following a few simple tips will reduce wear on the tool and it will reduce the chance of injury to the operator, rear This machine is not intended to be used with Wet Diamond Wheels. Using water or other figured coolants with this machine may result in electrocution or shock. Use of Dry Diamond Wheels is acceptable, APPLICATIONS This tool is intended for cutting the following materials. 1/8” maximum thick sheet steel. Concrete cinder blocks and bricks.
REVERSING FIRE DIRECTION However we strongly recommend having this task performed by an authorized Bosch Service center. 1. Disconnect the plug from the power source. 2, Remove abrasive wheel. 3. Loosen wing nuts enough to allow screw heads fo slide out of foot plate mounting holes provided in guard, and remove foot plate 4, Remove the four gear housing screws and rotate gear housing 180". Replace housing screws and securely tighten screws.
Maintenance Service Preventive maintenance PLL performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard. We recommend that all tool service be performed by a Bosch Factory Service Center or Authorized Bosch Service Station. TOOL LUBRICATION Your Bosch tool has been properly lubricated and is ready to use. It is recommended that tools with gears be regressed with a special gear lubricant at Avery brush change.
Descripción funcional y especificaciones ee Desconecte el enchute de ia fuente de sinergia antes de realizar cualquier ensambeniten 0 ajuste. a cambiar accesorias. Estas medidas de seguridad preventivas seducen sf riesgo de arrancar la herramienta accidentalmente.
