User's Manual
Table Of Contents
- ROAMEO Family Wireless Intercom System
- •TR-1800 •AP-1800
- CHAPTER 1 Certification Information
- CHAPTER 2 Introduction
- CHAPTER 3 System Overview
- CHAPTER 4 Site Survey
- CHAPTER 5 Installation
- CHAPTER 6 Basic Operation
- CHAPTER 7 Beltpack Overview
- System Quick Start
- Button Operation – Common
- Menu Structure – Main Menu Access
- Aux Input Menu
- AUX DIM Menu
- Volume Limit Menu
- Headset Select Menu
- Mic Gain
- Sidetone
- Mic Noise Gate
- Hot Mic
- Talk/Listen LED Buttons
- Front Display Brightness
- Top Display Brightness
- LCD Timeout
- Call Tally Talk
- Screen Flip
- Master Talk Switch
- Low Battery Alert
- Call Waiting Alert
- DECT Connection Alert
- Matrix Connection Alert
- Dark Mode Boot Alert
- Key Clicks Alert
- Alerts Levels
- Key Assignments
- Icon Help
- Scroll List
- CHAPTER 8 Access Point Overview
- AP-1800 Front Panel Description
- IPedit Requirements
- IPedit Main Window
- Configuration
- Device Name Field
- Description Field
- Version Field
- IP Address Field
- Netmask Field
- Gateway Address Field
- DNS Server Field
- Domain Name Field
- MAC Address Field
- Use Static IP Settings Check Box
- Disable RSTP Check Box
- Type Field
- Status Field
- Sessions Field
- AP Channels Field
- BP Channels Field
- Sync Display Box
- System ID Field
- PIN Field
- Zone Drop Down Menu
- CODEC Drop Down Menu
- AP ID Number Field
- Sync Master Check Box
- Intercom Alpha Field
- Channel Description Field
- Destination Type Drop Down Menu
- Destination Device Name Field (OMNEO devices and AP-1800 ROAMEO Access Point Only)
- Destination IP Address Field
- Destination Description Field
- Destination Channel Drop Down Menu
- Destination Channel Description Field
- Receiver Latency Field
- DECT BPID
- DECT Zone Selection Field
- Configuration
- CHAPTER 9 Maintenance
- CHAPTER 10 Troubleshooting, Accessories and Replacements
124 Access Point Overview ROAMEO System
Bosch Security Systems, Inc.
Technical Manual
F.01U.306.750
Rev. 01
Power LED
The Power LED is used to display the status of the AP-1800
Solid Green – Power/Normal Operation
Blinking Green – Normal Reset Mode
Solid Orange – Booting
Blinking Orange – Factory Reset Mode or unit’s software is being updated
Solid Red – Error
Blinking Red – Factory Defaults are being restored
Reset Button
The Reset button is used to reset the unit or place the unit in test mode
1
. There are two types of reset; Reset and Factory
Default Reset. A normal reset, resets the access point keeping all of the unit’s current settings. A factory default reset,
resets the access point to the factory settings.
Ethernet Connection
The Ethernet connectors are used to connect the access point to the network switch for communication with the Matrix.
Optical Connection
The Optical connector is used to connect the access point to the matrix system via a fiber optic cable. The optical port
accepts Small Form Factory Pluggable (SFP) transceiver modules.
IPedit Requirements
IPedit is a Windows-based GUI (Graphical User Interface) application for configuring and displaying OMNEO devices,
RVON devices, and AP-1800 ROAMEO devices connected to the Matrix system.
IMPORTANT: The following pages describe the fields most critical in AP-1800 ROAMEO Access Point
Configuration. For more detailed information about the IPedit software as a whole, see the IPedit
Technical Manual.
The Firmware Upload Tool can download firmware to devices running older firmware, but requires these versions in order to
automatically detect the devices and to view or modify the device configurations.
To fully use the IPedit application, the following minimum software versions must be installed:
Matrix
OMI - v6.1.5 and above
MCII-e - v3.4.0 and above
Keypanels
OKI - v6.1.2 and above
Tools (OMNEO Suite v6.13)
Firmware Upload Tool - v4.40.4085 and above
IPedit - v3.4.0 and above
AZedit - v5.3.0 and above
1. Test mode sets the unit to the TBR-6 mode. This is for agency testing only.