User's Manual
Table Of Contents
- ROAMEO Family Wireless Intercom System
- •TR-1800 •AP-1800
- CHAPTER 1 Certification Information
- CHAPTER 2 Introduction
- CHAPTER 3 System Overview
- CHAPTER 4 Site Survey
- CHAPTER 5 Installation
- CHAPTER 6 Basic Operation
- CHAPTER 7 Beltpack Overview
- System Quick Start
- Button Operation – Common
- Menu Structure – Main Menu Access
- Aux Input Menu
- AUX DIM Menu
- Volume Limit Menu
- Headset Select Menu
- Mic Gain
- Sidetone
- Mic Noise Gate
- Hot Mic
- Talk/Listen LED Buttons
- Front Display Brightness
- Top Display Brightness
- LCD Timeout
- Call Tally Talk
- Screen Flip
- Master Talk Switch
- Low Battery Alert
- Call Waiting Alert
- DECT Connection Alert
- Matrix Connection Alert
- Dark Mode Boot Alert
- Key Clicks Alert
- Alerts Levels
- Key Assignments
- Icon Help
- Scroll List
- CHAPTER 8 Access Point Overview
- AP-1800 Front Panel Description
- IPedit Requirements
- IPedit Main Window
- Configuration
- Device Name Field
- Description Field
- Version Field
- IP Address Field
- Netmask Field
- Gateway Address Field
- DNS Server Field
- Domain Name Field
- MAC Address Field
- Use Static IP Settings Check Box
- Disable RSTP Check Box
- Type Field
- Status Field
- Sessions Field
- AP Channels Field
- BP Channels Field
- Sync Display Box
- System ID Field
- PIN Field
- Zone Drop Down Menu
- CODEC Drop Down Menu
- AP ID Number Field
- Sync Master Check Box
- Intercom Alpha Field
- Channel Description Field
- Destination Type Drop Down Menu
- Destination Device Name Field (OMNEO devices and AP-1800 ROAMEO Access Point Only)
- Destination IP Address Field
- Destination Description Field
- Destination Channel Drop Down Menu
- Destination Channel Description Field
- Receiver Latency Field
- DECT BPID
- DECT Zone Selection Field
- Configuration
- CHAPTER 9 Maintenance
- CHAPTER 10 Troubleshooting, Accessories and Replacements
22 Introduction ROAMEO System
Bosch Security Systems, Inc.
Technical Manual
F.01U.306.750
Rev. 01
AP-1800 Specifications
General:
Audio Modes
G.722 wideband
G.726 narrowband
Max. beltpacks per AP-1800 (G.722)
5
Max. beltpacks per AP-1800 (G.726)
10
Connectivity
Standard 100Base-T or GigE Ethernet
Protocol Running on Ethernet
OMNEO
Ethernet Cabling Required
UTP CAT-5e or better
Power Supply Type
External DC, Wall Wart
Power Supply Input
100–240 VAC, 50–60 Hz, 0.6A
Power Supply Output (AP-1800 Input)
12VDC @ 1.5A, positive center
Environmental
Operating Temperature
32°F – 122°F (0°C – 50°C)
Storage Temperature
-4°F – 158°F (-20°C – 70°C)
Dimensions
5.17 in. H x 7.67 in. W x 1.52 in. D
(13.13 cm H x 19.47 cm W x 3.86 cm D)
Weight (w/antennas)
0.992 lbs. (450 g)
Weight (w/o antennas)
0.893 lbs.(405 g)
Connections:
Ethernet Connectors
2 x Standard RJ-45 Jacks
Optical Connector
Accepts small form factor pluggable SMP modules
RF Connectors
Reverse-SMA-F
RF Communications:
Frequency Range
1880-1900 MHz (EU - Europe, Asia, Australia)
1920-1930 MHz (NA - North America)
Communication Protocol
DECT
Carrier Frequency Selection
Automatic via DCS (Dynamic Channel Selection)
Modulation
GFSK
Power
Maximum Output Power (Peak)
200mW (EU)
100mW (NA)
Average Power, load dependent (G.722, wideband)
17-83mW (EU)
Average Power, load dependent (G.726, wideband)
8-83mW (EU)
Average Power, load dependent (G.722, wideband)
8-42mW (NA)
Average Power, load dependent (G.726, narrowband)
4-42mW (NA)
Antenna - Electrical
Frequency
1850-1990MHz
Gain
3dBi
Horizontal Beam Width
360°
Impedance
50 Ohm
Max. Power
50W
VSWR
<2:1
Polarization
Linear - along length of antenna
Antenna - Mechanical
Weight
0.77 oz (22g)
Length
5.2 in. (133mm)
Max. Diameter
0.52in. (13.2mm)
Finish
Matte Black
Connector
Reverse Polarity SMA Plug
Operating Temperature
-40°F to 131°F (-40°C to 55°C)
AP-1800 Certifications
RoHS, FCC Part 15D, FCC Part 15B, FCC/IC Class B
device, IC RSS-213, IC ICES-003, CE, EN 301 406, EN
301 489-6, EN 60950-1, RCM, Singapore, Mexico